● Commercial and Residential Architectural lighting
●Various colors
● Decoration lighting
● ROHS compliance
● Traffic signaling and wayside lighting
LEDlights Optoelectronics Inc.
Page 1/8
High power Light Emitting Diodes
Rev: 5.0 Date: 2008.07.16
■ PACKAGE DIMENSIONS ● Lambertian
Notes: 1. All dimensions are in mm. 2. Tolerances unless dimensions ±0.25mm. 3. Drawings are not to scale. 4. It is strongly recommended that the temperature of heat slug be not higher than 55℃. 5. Pd free , RoHS compliant
LEDlights Optoelectronics Inc.
Page 2/8
High power Light Emitting Diodes
Rev: 5.0 Date: 2008.07.16
■ ABSOLUTE MAXIMUM RATINGS Rating Parameter
Symbol
White/Warm White/Blue/Green
Red/Yellow
Unit
DC Forward Current
IF
350
150~350
mA
Pulse Forward Current
IF
500
550
Operating Temperature
Topr
-40 ~ +100
mA ℃
Storage Temperature
Tstg
-40 ~ +100
℃
Junction temperature
Tj
125
℃
ESD Sensitivity Manual Soldering Time at 260 ℃
VB
2000
V
Tsol
5
s
■ LUMINOUS FLUX AT IF=350mA Lens type
Color
Part Name
Min.
Typ.
Max.
White
NS-SP-E2-1-LW
40
80
Warm
NS-SP-E2-1-LV
40
70
Red
NS-UP-E2-1-LR
27
39
Yellow
NS-UP-E2-1-LY
27
39
Green
NS-UP-E2-1-LG
40
70
Blue
NS-UP-E2-1-LB
8
19
Unit
White
Lambertian
lm
■ DOMINANT WAVELENGTH OR PEAK WAVELENGTH OR COLOR TEMPERATURE CHARACTERISTICS AT IF=350mA Lens type
Color
Part Name
Min.
Typ.
Max.
Unit
White
NS-SP-E2-1-LW
4500
7000
K
Warm
NS-SP-E2-1-LV
2700
4500
K
Red
NS-UP-E2-1-LR
615
645
nm
Yellow
NS-UP-E2-1-LY
589
599
nm
Green
NS-UP-E2-1-LG
500
535
nm
Blue
NS-UP-E2-1-LB
455
475
nm
White
Lambertian
LEDlights Optoelectronics Inc.
Page 3/8
High power Light Emitting Diodes
Rev: 5.0 Date: 2008.07.16
■ FORWARD VOLTAGE CHARACTER AT IF=350mA Lens type
Lambertian
Color
Part Name
Min.
Typ.
Max.
White
NS-SP-E2-1-LW
3.00
3.85
Warm
NS-SP-E2-1-LV
3.00
3.85
Red
NS-UP-E2-1-LR
1.50
3.00
Yellow
NS-UP-E2-1-LY
1.50
2.95
Green
NS-UP-E2-1-LG
3.00
4.15
Blue
NS-UP-E2-1-LB
3.00
3.85
Unit
White
V
■ THERMAL RESISTANCE CHARACTERISTIC AT IF=350mA Lens type
Color
Part Name
∆VF/∆T Typ.
Lambertian
RθJ-B
White
NS-SP-E2-1-LW
-2
Unit mV/℃
Typ. 15
Unit ℃/W
Warm
NS-SP-E2-1-LV
-2
mV/℃
15
℃/W
Red
NS-UP-E2-1-LR
-2
mV/℃
15
℃/W
Yellow
NS-UP-E2-1-LY
-2
mV/℃
15
℃/W
Green
NS-UP-E2-1-LG
-2
mV/℃
15
℃/W
Blue
NS-UP-E2-1-LB
-2
mV/℃
15
℃/W
White
■ EMISSION ANGLE CHARACTERISTIC AT IF=350mA Part Name
Color
Lambertian
Focusing
2θ1 2
2θ1 2
NS-SP-E2-1-LW White
120
80
± 85
NS-SP-E2-1-LV
120
80
± 85
Warm
Side Emitting θpeak
Unit
White
NS-UP-E2-1-LR
Red
130
70
± 85
NS-UP-E2-1-LY
Yellow
130
70
± 85
NS-UP-E2-1-LG Green
140
60
± 80
NS-UP-E2-1-LB
140
60
± 80
Blue
LEDlights Optoelectronics Inc.
Degree
Page 4/8
High power Light Emitting Diodes
Rev: 5.0 Date: 2008.07.16
Note: 1. Flux is measured with an accuracy of ± 10%. 2. Forward voltage is measured with an accuracy of ± 0.2. 3. Wavelength is measured with an accuracy of ± 2nm. 4. Color temperature is measured with an accuracy of ± 50k. 5. Value for total power dissipation when two or three devices are lit simultaneously.
■ Reliability Test Item
Description Room Temperature Operation Life
Stress Condition 25℃
RTOLC
1000 hours
Wet High Temperature
85℃ / 85%RH
1000 hours
Temperature Cycling
-40/+110℃
200 cycles
Thermal Shock
30min dwell, <5min trans -40/+110℃
200 cycles
HTSL
High Temperature Storage Light
20min dwell, <20min trans 120℃
1000 hours
LTOL
Low Temperature Storage Light
-40℃
1000 hours
SHR
Solder Heat Resistance
260±5℃, 5 secs
MS
Mechanical Shock
1500G, 0.5mses pulse 5 shocks each 6 axis
ND
Natural Drop
On concrete from 1.2m, 3*times
RV
Random Vibration
6G RMS from 10 to 2KHz, 10mins/axis
VVF
Variable Vibration Frequency
10-2000-10Hz, 20G
WHT TC TS
Test Duration
1min, 1,5min,3timesx/axis
LEDlights Optoelectronics Inc.
Page 5/8
High power Light Emitting Diodes
Rev: 5.0 Date: 2008.07.16
■ Soldering Conditions Item
Description
Soldering
Reflow Soldering
Pre-heat Pre-heat time Peak temperature Soldering time Condition
Lead Soldering 120~150℃
Lead-free Solder 180~200℃
120 sec Max 240℃ Max
120 sec Max 260℃ Max
10 sec Max
10 sec Max
Refer to TemperatureProfile (1)
Refer to TemperatureProfile (2)
(1) Lead Solder
Remark
Hand Soldering Temperature 350℃ Max 3 sec Max Soldering (one time time only)
(2) Lead-free Solder 240℃ ℃ Max
2.5~5℃/sec
10 Sec Max
Pre-heating 120~150℃ ℃
10 Sec Max Pre-heating
60 sec Max
180~200℃ ℃
Above 220℃
60 sec Max 120sec Max
260℃ ℃ Max
1~5℃/sec
Above 200℃
120sec Max 2.5~5℃/sec
1~5℃/sec
Note: (1) Although the recommended soldering conditions are specified in the above table, reflow or hand soldering at the lowest possible temperature is desirable for the LEDs.
(2) A rapid-rate process is not recommended for cooling the LEDs down from the peak temperature. (3) Reflow soldering should not be done more than two times. (4) After soldering, do not warp the circuit board. (5) In soldering process, stress on the LEDs during heating should be avoided. Page 6/8 LEDlights Optoelectronics Inc.
High power Light Emitting Diodes
Rev: 5.0 Date: 2008.07.16
■ Soldering Note
(1)
Please do not press the lens over 1.5kg.
Good
(2)
Impermissibility
Please wear anti-static wrist or glove to prevent ESD damage when assembling.
Manual Soldering Time at 260 â. Tsol. 5 s. â¡ LUMINOUS FLUX AT IF=350mA. Lens type. Color. Part Name. Min. Typ. Max. Unit. White. NS-SP-E2-1-LW. 40. 80.
Jun 4, 2013 - Table 91. LQFP64 â 10 x 10 mm 64 pin low-profile quad flat package mechanical data. ..... to-pin, software and feature compatible with the STM32F2xx devices, allowing the user to ...... STMicroelectronics group of companies.
plus 56 bytes of NV SRAM. ... 4. 8. 7. 6. 5. SDA l. 2. 3. 4. 8. 7. 6. 5. X1. X2. VBAT. GND. VCC. SQW/OUT. SCL. SDA .... Bit 6 of the hours register is defined as the.
Aug 1, 2013 - implement the Ethernet application just by adding the simple socket program. It's faster and easier way rather than using any other Embedded ...
*Extra components not needed. * Long transmission distance * Low power consumption. *4 pins packaged and fully interchangeable. 2.Description: Description: AM2303 output calibrated digital signal. It utilizes exclusive digital-signal-collecting-techn
Dec 6, 1990 - For the DC characteristics see â74HC/HCT/HCU/HCMOS Logic Family Specificationsâ. Output capability: bus driver. ICC category: MSI. AC CHARACTERISTICS FOR 74HC. GND = 0 V; tr = tf = 6 ns; CL = 50 pF. SYMBOL. PARAMETER. Tamb (°C). UN
Nov 28, 2013 - advanced technology and highly integrated design, GC3355 target to provide multiple function and low cost solution in SHA256 application ...
Office automation equipment. FFeatures. 1) A plastic lens is used for high sensitivity. 2) A built-in visible light filter minimizes the influence of stray light.
Page 1 of 16. RE 28389, edition: 2013-05, Bosch Rexroth AG. 2-way flow control valve. Features. â· For subplate mounting. â· Porting pattern according to DIN ...
Axial piston variable pump. A4CSG Series 3x. RE 92105. Edition: 12.2016. Replaces: 07.2016. Type code for standard program 2. Hydraulic fluids 4. Shaft seal ...
With check valve;. with external closing. Type 2FRM 6 A...R... A B. P. A B. P. Page 3 of 16. datasheet 2FRM6A.pdf. datasheet 2FRM6A.pdf. Open. Extract.
Nov 25, 2004 - Product Description. Tmote Sky is an ultra low power wireless module for use in sensor networks, monitoring applications, and rapid application prototyping. Tmote Sky leverages industry standards like USB and. IEEE 802.15.4 to interope
Nov 25, 2004 - Figure 2 : Physical dimensions of Tmote Sky. All units are in inches unless otherwise noted. MIN. NOM. MAX. UNIT. Width. 1.24. 1.26. 1.29 in.Missing:
the MQ-5 on temperature and humidity. Ro: sensor resistance at 1000ppm of H2 in air at. 33%RH and 20 degree. Rs: sensor resistance at different temperatures.Missing:
Threaded pin with hexagon and protective cap. ⢠Lockable rotary knob with scale. ⢠Rotary knob with scale. â With pressure gauge connection. Content Page.
Oct 13, 2008 - The LDT0-028K is a flexible component comprising a 28 µm thick piezoelectric PVDF polymer film with screen-printed Ag-ink electrodes, laminated to a 0.125 mm polyester substrate, and fitted with two crimped contacts. As the piezo film
Notes: 1. Sensing resistance in air R0 is measured under controlled ambient conditions, i.e. synthetic air at 23. ±5°C and 50 ± 10% RH for RED sensor and ...
Jan 15, 2013 - Up to 10 mm glass; Up to 5 mm plastic (electrode size dependent) ..... or the design should be such that these lines are not switched ..... Top View .... CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL.
connectivity to myriad video displays such as LCD and CRT monitors, in addition to the .... In addition, advanced processing algorithms are employed ... (to host). Configuration. Register Blocks. PCLK. VSYNC. HSYNC. DE. D[23:0]. WS. I2S3/ ...
SW-200D is two balls type single direction tilt sensitive trigger switch. 2. When the products tilt to the conductive terminal (silver-feet pin end A) and the tilt angle ...
