General-purpose Operational Amplifiers /Comparators
TROPHY SERIES Comparators LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR ●Description The Universal Standard family LM393 / LM339/ LM2903 / LM2901 monolithic ICs integrate two/four independent comparators on a single chip and feature high gain, low power consumption, and an operating voltage range from 2[V] to 36[V] (single power supply).
No.11094EBT03
TROPHY SERIES
Dual LM393 family LM393DR LM393PWR LM393DGKR
Quad
LM2903 family
LM339 family
LM2903DR LM2903PWR LM2903DGKR LM2903VQDR LM2903VQPWR
LM339DR LM339PWR
LM2901 family LM2901DR LM2901PWR LM2901VQDR LM2901VQPWR
●Features 1) Operating temperature range Commercial Grade LM339/393 family : 0[℃] to + 70[℃] Extended Industrial Grade LM2903/2901 family : -40[℃] to +125[℃] 2) Open collector output 3) Single / dual power supply compatible 4) Low supply current 0.8[mA] typ. (LM393/339/2903/2901 family) 5) Low input-bias current: 25[nA] typ. 6) Low input-offset voltage: 2[mV] typ. 7) Differential input voltage range equal to maximum rating 8) Low output saturation voltage 9) TTL,MOS,CMOS compatible output ●Pin Assignment
1OUT
1IN-
1
2
1IN+
3
GN D
4
8
7
－ ＋
＋
－
1OUT
1
14
OUT3
2OUT
2
13
OUT4
Vcc
3
12
GND
Vcc
2OUT
6
2IN-
5
2IN+
－ ＋ 2IN-
4
11
4IN+
2IN+
5
10
4IN-
1IN-
6
9
3IN+
8
3IN-
－ ＋ 1IN+
SOIC8 LM393DR LM2903DR LM2903VQDR
TSSOP8 LM393PW R LM2903PW R LM2903VQPW R
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
MSOP8/VSSOP8 LM393DGKR LM2903DGKR
7
SOIC14 LM339DR LM2901DR LM2901VQDR
1/17
－ ＋
－ ＋
TSSOP14 LM339PW R LM2901PW R LM2901VQPW R
2011.06 - Rev.B
LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR
Technical Note
●Absolute Maximum Ratings (Ta=25℃) Parameter
Symbol
Supply Voltage
Ratings LM393 family
LM339 family
LM2903 family
LM2901 family
Unit
Vcc-GND
+36
V
Vid
±36
V
Input Differential Voltage Common-mode Input
Vicm
Operating Temperature
Topr
Storage Temperature Range
Tstg
-65 to +150
℃
Tj
+150
℃
Maximum Junction Temperature
-0.3 to +36 0 to +70
V -40 to +125
℃
●Electric Characteristics ○LM393/339 family(Unless otherwise specified, Vcc=+5[V]) Limits Parameter
Temperature Symbol range
25℃ Input Offset Voltage (*1)
Input Offset Current (*1)
Input Bias Current (*1)
Common-mode Input Voltage Range
Min.
Typ.
Max.
Min.
Typ.
Max.
－
2
7
－
2
7
IOL
Supply Current
ICC
88
nA
VO=1.4[V]
88
nA
VO=1.4[V]
88
－
－
9
25℃
－
5
50
－
5
50
Full range
－
－
250
－
－
150
25℃
－
25
250
－
25
250
Full range
－
－
400
－
－
400
25℃
－
－
Vcc-1.5
－
－
Vcc-1.5
Full range
－
－
Vcc-2.0
－
－
Vcc-2.0
25℃
25
200
－
25
200
－
V/mA
25℃
－
0.1
－
－
0.1
－
nA
VID=1[V],VO=5[V]
Full range
－
－
1
－
－
1
μA
VID=1[V],VO=30[V]
25℃
－
150
400
－
150
400 mV
VID=-1[V],IOL=4[mA]
89
Full range
－
－
700
－
－
700
25℃
6
－
－
6
16
－
mA
VID=-1[V],VOL=1.5[V]
89
25℃
－
0.8
1
－
0.8
2
－
V
88
Vcc=15[V] VO=1.4 to 11.4[V], RL≧15[kΩ],VRL=15[V]
88
89
RL=∞,Vcc=5V mA
Full range
Tre
Vcc=5 to 30[V],VO=1.4[V] VIC=VIC(min)
9
VOL
Low Level Output Current
mV －
VICR
IOH
Fig. No.
－
IIB
High Level Output Current
condition
Full range
IIO
AVD
Response Time
Unit
LM339 family
VIO
Large Signal Differential Voltage Amplification
Low Level Output Voltage
LM393 family
－
－
2.5
－
－
－
－
1.3
－
－
1.3
－
－
0.3
－
－
0.3
－
μs
25℃
89 RL=∞,Vcc=30[V] RL=5.1[kΩ],VRL=5[V],CL=15pF VIN=100[mVp-p], overdrive=5[mV] RL=5.1[kΩ],VRL=5[V], CL=15pF VIN=TTL-Level input step Vref=1.4[V]
89
(*1) Absolute value
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
2/17
2011.06 - Rev.B
LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR
Technical Note
○LM2903/2901 family(Unless otherwise specified, Vcc=+5[V]) Limits Parameter
Symbol
Temperature range
25℃ Input Offset Voltage (*2)
Input Offset Current (*2)
Input Bias Current (*2)
Common-mode Input Voltage Range
Min.
Typ.
Max.
－
2
7
－
2
7
15
－
－
15
25℃
－
5
50
－
5
50
Full range
－
－
200
－
－
200
25℃
－
25
250
－
25
250
Full range
－
－
500
－
－
500
25℃
－
－
Vcc-1.5
－
－
Vcc-1.5
Full range
－
－
Vcc-2.0
－
－
Vcc-2.0
25℃
25
100
－
25
100
25℃
－
0.1
－
－
Full range
－
－
1
25℃
－
150
25℃
－
Full range IOL
25℃
ICC
25℃
IIO
IIB
VOL
Tre
Condition
Fig. No
mV
Vcc=5 to MAX),VO=1.4[V] VIC=VIC (min)
88
nA
VO=1.4[V]
88
nA
VO=1.4[V]
88
V
－
88
－
V/mV
Vcc=15[V],VOUT=1.4 to 11.4[V], RL≧15[kΩ],VRL=15[V]
88
0.1
－
nA
VID=1[V], VOH=5[V]
－
－
1
μA
VID=1[V], VOH=MAX
400
－
150
500
150
400
－
150
400
mV
VIN(-)=1[V],VIN(+)=0[V] ISINK≦4[mA]
89
－
－
700
－
－
700
6
16
－
6
16
－
mA
VID=-1[V], VOL=1.5[V]
89
－
0.8
2
－
0.8
2
VICR
LM2901(*3)
Response Time
Max.
－
IOH
Supply Current
Typ.
－
High Level Output Current
Low Level Output Current
Min.
Full range
AVD
LM2901V(*3)
Unit
LM2901 family
VIO
Large Signal Differential Voltage Amplification
Low Level Output Voltage
LM2903 family
89
RL=∞,Vcc=5V mA
－
1
2.5
－
1
2.5
－
1.3
－
－
1.3
－
－
0.3
－
－
0.3
－
μs
25℃
89 RL=∞,Vcc=MAX(*7) RL=5.1[Ω],VRL=5[V],CL=15pF VIN=100[mVp-p], Overdrive=5[mV] RL=5.1[kΩ],VRL=5[V], CL=15pF VIN=TTL-Level input step Vref=1.4[V]
89
(*2) Absolute value (*3) Supply Voltage Maximum Value LM2901DR, LM2901PWR MAX=30[V], LM2901VQDR, LM2901VQPWR MAX=32[V]
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
3/17
2011.06 - Rev.B
LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR
Technical Note
●Reference Data LM393 family LM393 family
LM393 family
1
LM393DGKR LM393PWR
400 LM393DR
200
0 0
25
0.6
0.4 70℃
0.2
75
100
125
10 20 30 SUPPLY VOLTAGE [V]
Fig.1
40
0
OUTPUT SATU RATION VOLT AGE [mV]
25℃
200
0℃
2V
300 5V
200
10 20 30 SUPPLY VOLTAGE [V]
36V
100
1.8 1.6 1.4
10
20 30 40 50 60 70 AMBIENT TEMPERATURE [℃]
Fig.4
70℃
1.0 0.8 0.6 0.4 0℃
0.2
80
0
2
4
6
8
Fig. 5
Fig. 6 Low Level Output Voltage – Output Sink Current
(IOL=4[mA])
(IOL=4[mA])
(VCC=5[V]) LM393 family
LM393 family
INPUT OFFSET VOLTAGE [mV]
40
30 36V 5V
20
2V
0
LM393 family
8
8
6
6
4 0℃
2
25℃
0 -2
70℃
-4 -6 -8
20 30 40 50 60 70 AMBIEN T TEMPERATURE [℃]
10 12 14 16 18 20
OUTPUT SINK CURRENT [mA]
Output Saturation Voltage – Ambient Temperature
Output Saturation Voltage – Supply Voltage
10
25℃
1.2
0.0
0
40
4 2V
2
5V
0 -2 36V
-4 -6 -8
0
80
10
20
30
40
0
Fig. 7
10
20
30
40
50
60
70
80
AMBIENT TEMPERATURE [℃]
SUPPLY VOLTAGE [V]
Fig. 8
Output Sink Current – Ambient Temperature
80
LM393 family
2.0
0
0
20 30 40 50 60 70 AMBIENT TEMPER ATURE [℃]
Fig. 3
400
0
10
10
Supply Current – Ambient Temperature
500
70℃
0
5V
LM393 family
LM393 family
OUTPUT SATURATION VOLTAGE [mV]
2V
0.2
Fig.2
500
100
0.4
Supply Current – Supply Voltage
Derating Curve
300
0.6
0 0
AMBIENT TEMPERATURE [℃] .
400
36V
0
70
50
25℃
LOW LEVEL OUTPUT VOLTAGE [V]
600
0.8 SUPPLY CURRENT [mA]
SUPPLY CURRENT [mA]
0.8
INPUT OFFSET VOLTAGE [mV]
POWER DISSIPATION [mW] .
0℃
800
OUTPUT SINK CURR ENT [mA]
LM393 family
1
.
1000
Fig. 9
Input Offset Voltage – Supply Voltage
Input Offset Voltage – Ambient Temperature
(VOUT=1.5[V]) LM393 family
.
160
100
0℃
25℃
80 60 40 70℃
20
INPUT OFFSET CURRENT [nA]
INPUT BIAS CURRENT [nA]
120
120 36V
100 80
5V
60 40 2V
20
0
10
20
30
40
SUPPLY VOLTAGE [V]
Fig. 10 Input Bias Current – Supply Voltage
30 20
0℃
10 0 25℃
-10
70℃
-20 -30 -40
0
0
LM393 family
50 40
140
140 INPUT BIAS CURRENT [nA]
LM393 family
160
-50
0
10
20 30 40 50 60 70 AMBIENT TEMPERATURE [℃]
80
0
10 20 30 SUPPLY VOLTAGE [V]
40
Fig. 11
Fig. 12
Input Bias Current – Ambient Temperature
Input Offset Current – Supply Voltage
(*)The data above is ability value of sample, it is not guaranteed. LM393family:0[℃]~+70[℃]
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
4/17
2011.06 - Rev.B
LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR
Technical Note
●Reference Data LM393 family
20 10
5V
0 -10 2V
-20 -30 -40 -50
25℃
130
LARGE SIGNAL VOLT AGE GAIN [dB]
LARGE SIGNAL VOLTAGE GAIN [dB]
120 110 100
70℃
0℃
90 80 70
20 30 40 50 60 70 AMBIENT TEMPERATURE [℃]
80
0
10 20 30 SUPPLY VOLTAGE [V]
Fig. 13
25℃
100
70℃
60 40
140 130 120 36V
110
5V
100 90 80 2V
70 60
10 20 30 SUPPLY VOLTAGE [V]
40
0
10
Fig. 16
80 70
0
10
4
3 5mV overdrive
2 20mV overdrive
1 100mV overdrive
80
Large Signal Voltage Gain – Ambient Temperature LM393 family
140 130 120 110 100 90 80 70 60 0
10
20 30 40 50 60 70 AMBIENT TEMPERAT URE [°C]
80
Fig. 18 Power Supply Rejection Ratio – Ambient Temperature
5
4
3 5mV overdrive
2
20mV overdrive 100mV overdrive
1
0
0 20 30 40 50 60 70 AMBIENT TEMPERATURE [°C]
20 30 40 50 60 70 AMBIENT TEMPERATURE [°C]
LM393 family
.
LM393 family
RESPONSE TIME (HIGH to LOW) [μ ｓ]
. . RESPONSE T IME (LOW to HIGH) [μs]
80
Common Mode Rejection Ratio – Ambient Temperature
5
10
20 30 40 50 60 70 AMBIENT TEMPERATURE [°C]
Fig. 17
Common Mode Rejection Ratio – Supply Voltage
0
5V 2V
90
LM393 family
POWER SUPPLY REJECTION RAT IO [dB]
COMMON MODE REJECTION RATIO[dB] .
140
0
100
Fig. 15
LM393 family
80
110
Fig. 14
160
0℃
36V
120
40
Large Signal Voltage Gain – Supply Voltage
Input Offset Current – Ambient Temperature
120
130
.
10
140
60
60
0
POWER SUPPLY REJECTION RATIO [dB]
IN PUT OFFSET CU RRENT [nA]
36V
30
.
140
40
LM393 family
LM393 family
.
LM393 family
50
80
Fig. 19
0
10
20 30 40 50 60 70 AMBIENT TEMPERATURE [°C]
80
Fig. 20
Response Time (Low to High) – Ambient Temperature
Response Time (High to Low) –Ambient Temperature
(VCC=5[V],VRL=5[V],RL=5.1[kΩ])
(VCC=5[V],VRL=5[V],RL=5.1[kΩ])
(*)The data above is ability value of sample, it is not guaranteed. LM393family:0[℃]~+70[℃]
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
5/17
2011.06 - Rev.B
LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR
Technical Note
●Reference Data LM339 family LM339 family
LM339 family
.
1
400 LM339DR
200
0
25
70
50
75
0.8 SUPPLY CURRENT [mA]
600
0
0℃
0.8
LM339PWR
SUPPLY CURRENT [mA]
25℃
0.6
0.4 70℃
0.2
0
100
125
10 20 30 SUPPLY VOLTAGE [V]
AMBIENT TEMPERATURE [℃] .
Fig.21
Fig.22 Supply Current – Supply Voltage
25℃
200
0℃
400 2V
300 5V
200
36V
100
0
10
20 30 40 50 60 70 AMBIENT TEMPERATURE [℃]
Fig.24
1.6 1.4
25℃
1.2
70℃
1.0 0.8 0.6 0.4 0℃
0.2
80
0
2
4
6
8
Fig. 25
Fig. 26 Low Level Output Voltage – Output Sink Current
(IOL=4[mA])
(IOL=4[mA])
(VCC=5[V]) LM339 family
LM339 family
36V 5V
20
2V
10
0
LM339 family
8
8
6
6
INPUT OFFSET VOLTAGE [mV]
INPUT OFFSET VOLTAGE [mV]
40
30
4 0℃
2
25℃
0 -2
70℃
-4 -6 -8
20 30 40 50 60 70 AMBIEN T TEMPERATURE [℃]
10 12 14 16 18 20
OUTPUT SINK CURRENT [mA]
Output Saturation Voltage – Ambient Temperature
Output Saturation Voltage – Supply Voltage
OUTPUT SINK CURR ENT [mA]
1.8
0.0 0
40
4 2V
2
5V
0 -2 36V
-4 -6 -8
0
80
80
LM339 family
2.0
0
10
20 30 40 50 60 70 AMBIENT TEMPER ATURE [℃]
Supply Current – Ambient Temperature
LOW LEVEL OUTPUT VOLTAGE [V]
OUTPUT SATU RATION VOLT AGE [mV]
OUTPUT SATURATION VOLTAGE [mV]
70℃
0
10
LM339 family
400
10 20 30 SUPPLY VOLTAGE [V]
2V
0.2
0
500
0
0.4
Fig. 23
LM339 family
500
100
0.6
40
Derating Curve
300
36V 5V
0 0
10
20
30
40
0
10
20
30
40
50
60
70
80
AMBIENT TEMPERATURE [℃]
SUPPLY VOLTAGE [V]
Fig. 27
Fig. 28
Fig. 29
Output Sink Current – Ambient Temperature
Input Offset Voltage – Supply Voltage
Input Offset Voltage – Ambient Temperature
(VOUT=1.5[V]) LM339 family
.
160
LM339 family
160
40
140 INPUT BIAS CURRENT [nA]
140 120 100
0℃
25℃
80 60 40 70℃
120
80
40
0
0 10
20
30
40
SUPPLY VOLTAGE [V]
Fig. 30
Input Bias Current – Supply Voltage
5V
60
20
0
36V
100
20
LM339 family
50 INPUT OFFSET CURRENT [nA]
POWER DISSIPATION [mW] .
800
INPUT BIAS CURRENT [nA]
LM339 family
1
1000
2V
30 20 0℃
10 0 25℃
-10 70℃
-20 -30 -40 -50
0
10
20 30 40 50 60 70 AMBIENT TEMPERATURE [℃]
80
0
10 20 30 SUPPLY VOLTAGE [V]
40
Fig. 31
Fig. 32
Input Bias Current – Ambient Temperature
Input Offset Current – Supply Voltage
(*)The data above is ability value of sample, it is not guaranteed. LM339family:0[℃]~+70[℃]
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
6/17
2011.06 - Rev.B
LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR
Technical Note
●Reference Data LM339 family
20 10
5V
0 -10 2V
-20 -30 -40 -50
130
LARGE SIGNAL VOLT AGE GAIN [dB]
LARGE SIGNAL VOLTAGE GAIN [dB]
IN PUT OFFSET CU RRENT [nA]
36V
30
.
140
40
LM339 family
LM339 family
.
LM339 family
50
25℃
120 110 100
70℃
0℃
90 80 70 60
0
10
20 30 40 50 60 70 AMBIENT TEMPERATURE [℃]
80
140 130 36V
120 110 100
5V
2V
90 80 70 60
0
10 20 30 SUPPLY VOLTAGE [V]
Fig. 33
10
20 30 40 50 60 70 AMBIENT TEMPERATURE [°C]
Fig. 34
Fig. 35
Large Signal Voltage Gain – Supply Voltage
Large Signal Voltage Gain – Ambient Temperature
80
.
Input Offset Current – Ambient Temperature
0
40
LM339 family
120 25℃
0℃
100 80
70℃
60 40
140 130 120 36V
110
5V
100 90 80 2V
70 60
0
10 20 30 SUPPLY VOLTAGE [V]
40
0
10
20 30 40 50 60 70 AMBIENT TEMPERATURE [°C]
Fig. 36
4
3 5mV overdrive
2 20mV overdrive
1 100mV overdrive
0 10
20 30 40 50 60 70 AMBIENT TEMPERATURE [°C]
80
Fig. 39
130 120 110 100 90 80 70 60 0
10
20 30 40 50 60 70 AMBIENT TEMPERAT URE [°C]
80
Power Supply Rejection Ratio – Ambient Temperature
.
LM339 family
5 RESPONSE TIME (HIGH to LOW) [μ ｓ]
. .
LM339 family
140
Fig. 38
Common Mode Rejection Ratio – Ambient Temperature
5
0
80
Fig. 37
Common Mode Rejection Ratio – Supply Voltage
RESPONSE T IME (LOW to HIGH) [μs]
POWER SUPPLY REJECTION RATIO [dB]
140
LM339 family
LM339 family
POWER SUPPLY REJECTION RAT IO [dB]
COMMON MODE REJECTION RATIO[dB] .
160
4
3 5mV overdrive
2
20mV overdrive 100mV overdrive
1
0 0
10
20 30 40 50 60 70 AMBIENT TEMPERATURE [°C]
80
Fig. 40
Response Time (Low to High) – Ambient Temperature
Response Time (High to Low) –Ambient Temperature
(VCC=5[V],VRL=5[V],RL=5.1[kΩ])
(VCC=5[V],VRL=5[V],RL=5.1[kΩ])
(*)The data above is ability value of sample, it is not guaranteed. BA10393F:-40[℃]~+70[℃] (*)上記のデータはサンプルの実力値であり、保証するものではありません。BA10393F:-40[℃]～+85[℃]
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
7/17
2011.06 - Rev.B
LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR
Technical Note
●Reference Data LM2903 family LM2903 family
SUPPLY CURRENT [mA]
800
600
LM2903PT 600
LM2903DGKR
400 400
LM2903DT
200
LM2903 family
LM2903 family
200
1.6
1.6
1.4
1.4
SUPPLY CURRENT [mA]
POWER DISSIPATION POWER DISSIPATION Pd [mV] [mW]
800 1000
1.2 1.0 25℃
-40℃
0.8 0.6 0.4 0.2
25 25
50 50
75 75
100 100
125 125
AMBIENT TEMPERTURE [℃]
AMBIENT TEMPERATURE
10
.
20
30
Fig. 42
100
25℃ -40℃
0 20
30
50
75
100 125 150
LM2903 family
2
200
1.8 150 2V
100 5V
50
36V
1.6 1.4 1.2
25℃
125℃
1 0.8 105℃
0.6 0.4 0.2
-40℃
0
0
40
-50
-25
SUPPLY VOLTAGE [V]
0
25
50
75
100
125
0
150
2
4
6
8
10
12
14
16
18
Fig. 45
Fig. 46
Output Saturation Voltage – Supply Voltage
Output Saturation Voltage – Ambient Temperature
Low Level Output Voltage – Output Sink Current
(IOL=4[mA])
(IOL=4[mA])
(VCC=5[V])
5V 36V
20 2V
10
0
8
8
6
6
4
INPUT OFFSET VOLTAGE [mV]
INPUT OFFSET VOLTAGE [mV]
40
30
LM2903 family
LM2903 family
LM2903 family
-40℃
2 0 25℃
-2
105℃
125℃
-4 -6
-25
0
25
50
75
100 125 150
4 2V
2 0 5V
-2
36V
-4 -6 -8
-8 -50
20
OUTPUT SINK CURRENT [mA]
SUPPLY VOLTAGE [V]
Fig. 44
OUTPUT SINK CURRENT [mA]
25
Supply Current – Ambient Temperature
OUTPUT VOLTAGE [V]
105℃
0
LM2903 family
MAXIMUM OUTPUT VOLTAGE [mV]
MAXIMUM OUTPUT VOLTAGE [mV]
125℃
-25
Fig. 43
LM2903 family
10
-50
AMBIENT TEMPERATURE [℃]
Supply Current – Supply Voltage
200
0
2V
SUPPLY VOLTAGE [V]
[℃]
Fig. 41
50
0.4
40
Derating Curve
150
5V
0.6
0.0 0
150 150
36V
0.8
125℃
0.0
00
1.0
0.2 105℃
00
1.2
0
10
20
30
-50
40
-25
0
25
50
75
100 125 150
AMBIENT TEMPERATURE [℃]
SUPPLY VOLTAGE [V]
AMBIENT TEMPERATURE [℃]
Fig. 47
Fig. 48
Fig. 49
Output Sink Current – Ambient Temperature
Input Offset Voltage – Supply Voltage
Input Offset Voltage – Ambient Temperature
(VOUT=1.5[V]) LM2903 family
LM2903 family
50
140
140
40
120 -40℃
100
25℃
80 60 40 105℃
20
INPUT OFFSET CURRENT[nA]
160
INPUT BIAS CURRENT [nA]
INPUT BIAS CURRENT [nA]
LM2903 family
160
120 100
36V
80 60 40
5V
20
2V
125℃
0
5
10
15
20
25
30
35
SUPPLY VOLTAGE [V]
Fig. 50 Input Bias Current – Supply Voltage
20 -40℃
25℃
10 0 -10
105℃
125℃
-20 -30 -40
0
0
30
-50 -50
-25
0
25
50
75
100 125 150
AMBIENT TEMPERATURE [℃]
Fig. 51 Input Bias Current – Ambient Temperature
0
10
20
30
40
SUPPLY VOLTAGE [V]
Fig. 52 Input Offset Current – Supply Voltage
(*)The data above is ability value of sample, it is not guaranteed.LM2903family:-40[℃]～+125[℃]
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
8/17
2011.06 - Rev.B
LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR
Technical Note
●Reference Data LM2903 family LM2903 family
140
40 30 20
2V
10 0 -10 5V
-20
36V
-30 -40 -50
130
LARGE SINGAL VOLTAGE GAIN [dB]
140
LARGE SINGAL VOLTAGE GAIN [dB]
INPUT OFFSET CURRENT [nA]
LM2903 family
LM2903 family
50
105℃
125℃
120 110 100 25℃
-40℃
90 80 70 60
-50
-25
0
25
50
75
100 125 150
0
10
AMBIENT TEMPERATURE [℃]
20
30
130 36V
120 110 100
80 70 60 -50
40
5V
15V
90
-25
0
25
50
75
100 125 150
AMBIENT TEMPERATURE [℃]
SUPPLY VOLTAGE [V]
Fig. 53
Fig. 54
Fig. 55
Input Offset Current – Ambient Temperature
Large Signal Voltage Gain – Supply Voltage
Large Signal Voltage Gain – Ambient Temperature
125℃
80
25℃
-40℃
60 40 0
10
20
30
40
125
36V
100 75 5V 2V
50 25 0 -25
0
25
Fig. 56
50
75
160 140 120 100 80 60 25
50
100 125 150
-1
0
1
75
2
3
Input Offset Voltage – Input Voltage (VCC=5V) LM2903 family
3
2 -40℃
25℃
1
0 -100
100 125 150
105℃
-80
-60
-40
5
Fig. 58
4
125℃
4
INPUT VOLTAGE [V]
5
AMBIENT TEMPERATURE [℃]
-20
0
OVER DRIVE VOLTAGE [V]
5
4
3 100mV overdrive 20mV overdrive
5mV overdrive
2
1
0 -50
-25
0
25
50
75
100 125 150
AMBIENT TEMPERATURE [℃]
Fig. 59
Fig. 60
Power Supply Rejection Ratio – Ambient Temperature
Response Time (Low to High) – Over Drive Voltage
Response Time (Low to High) – Ambient Temperature
(VCC=5[V],VRL=5[V],RL=5.1[kΩ])
(VCC=5[V],VRL=5[V],RL=5.1[kΩ])
RESPONSE TIME (HIGH TO LOW)[μs]
5
4
3 125℃ 105℃
2
25℃
Fig. 61
LM2903 family
LM2903 family
RESPONSE TIME (HIGH TO LOW)[μs]
-4
LM2903 family
RESPONSE TIME (LOW TO HIGH)[μs]
POWER SUPPLY REJECTION RATIO [dB]
180
0
-2
Fig. 57
LM2903 family
-25
125℃
0
Common Mode Rejection Ratio – Ambient Temperature
200
-50
-40℃
2
AMBIENT TEMPERATURE [℃]
SUPPLY VOLTAGE [V]
Common Mode Rejection Ratio – Supply Voltage
105℃
25℃
4
-6 -50
RRESPONSE TIME (LOW TO HIGH)[μs]
105℃
100
6
150
INPUT OFFSET VOLTAGE [mV]
120
COMMON MODE REJECTION RATIO [dB]
COMMON MODE REJECTION RATIO [dB]
140
LM2903 family
LM2903 family
LM2903 family
160
-40℃
1
5
4 100mV overdrive
3
20mV overdrive 5mV overdrive
2
1
0
0 0
20
40
60
80
100
OVER DRIVE VOLTAGE [V]
Fig. 62
-50
-25
0
25
50
75
100 125 150
AMBIENT TEMPERATURE [℃]
Fig. 63
Response Time (High to Low) – Over Drive Voltage
Response Time (High to Low) – Ambient Temperature
(VCC=5[V],VRL=5[V],RL=5.1[kΩ])
(VCC=5[V],VRL=5[V],RL=5.1[kΩ])
(*)The data above is ability value of sample, it is not guaranteed. LM2903family:-40[℃]～+125[℃]
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
9/17
2011.06 - Rev.B
LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR
Technical Note
●Reference Data LM2901 family LM2901 family
1000 1000
LM2901 family
2.0
LM290PWR 600 600
400 400
LM2901DR 200 200
1.4 25℃
1.6 -40℃
1.4 1.2 1.0 0.8 0.6
125℃
0.4
0
25
50
25
75
50
100
75
125
100
125
AMBIENT TEMPERATURE [℃] AMBIENT TEMPERATURE [℃]
0
150
150
10
20
Fig. 64
30
0
25
50
100
25℃ -40℃
0 30
100 125 150
Supply Current – Ambient Temperature LM2901 family
2 1.8
150 2V
100
5V 36V
50
1.6 1.4
25℃
125℃
1.2 1 0.8
105℃
0.6 0.4 0.2
-40℃
0
0 20
75
Fig. 66
OUTPUT VOLTAGE [V]
105℃
40
-50
-25
SUPPLY VOLTAGE [V]
0
25
50
75
100
125
0
150
2
4
6
8
10
12
14
16
Fig. 68 Output Saturation Voltage – Ambient Temperature
Low Level Output Voltage – Output Sink Current
(IOL=4[mA])
(IOL=4[mA])
(VCC=5[V])
8
5V
36V
20 2V
10
0
8
INPUT OFFSET VOLTAGE [mV]
INPUT OFFSET VOLTAGE [mV]
30
LM2901 family
LM2901 family
40
6 4
-40℃
2 0 25℃
-2
105℃
125℃
-4 -6
0
25
50
75
100 125 150
6 4 2V
2 0 5V
-2
36V
-4 -6 -8
-8 -25
20
Fig. 69
Output Saturation Voltage – Supply Voltage LM2901 family
18
OUTPUT SINK CURRENT [mA]
SUPPLY VOLTAGE [V]
Fig. 67
OUTPUT SINK CURRENT [mA]
-25
AMBIENT TEMPERATURE [℃]
LM2901 family
MAXIMUM OUTPUT VOLTAGE [mV]
MAXIMUM OUTPUT VOLTAGE [mV]
125℃
-50
2V
-50
200
10
0.4
Fig. 65
LM2901 family
0
5V
0.6
40
Supply Current – Supply Voltage
200
50
36V
0.8
SUPPLY VOLTAGE [V]
Derating Curve
150
1.0
0.0
0.0
0
1.2
0.2
105℃
0.2
00
SUPPLY CURRENT [mA]
SUPPLY CURRENT [mA]
POWER DISSIPATION [mW]
POWER DISSIPATION Pd [mW]
1.8
800 800
LM2901 family
1.6
0
10
AMBIENT TEMPERATURE [℃]
20
30
-50
40
-25
0
25
50
75
100 125 150
AMBIENT TEMPERATURE [℃]
SUPPLY VOLTAGE [V]
Fig. 70
Fig. 71
Fig. 72
Output Sink Current – Ambient Temperature
Input Offset Voltage – Supply Voltage
Input Offset Voltage – Ambient Temperature
(VOUT=1.5[V])
120 25℃
-40℃
100 80 60 40
105℃
20
160
50
140
40
INPUT OFFSET CURRENT[nA]
INPUT BIAS CURRENT [nA]
INPUT BIAS CURRENT [nA]
140
120 100
36V
80 60 40 5V
20
2V
125℃
0
0 0
5
10
15
20
25
30
35
SUPPLY VOLTAGE [V]
LM2901 family
LM2901 family
LM2901 family
160
30 20 -40℃
10
25℃
0 -10
105℃
125℃
-20 -30 -40 -50
-50
-25
0
25
50
75
100 125 150
AMBIENT TEMPERATURE [℃]
0
10
20
30
40
SUPPLY VOLTAGE [V]
Fig. 73
Fig. 74
Fig. 75
Input Bias Current – Supply Voltage
Input Bias Current – Ambient Temperature
Input Offset Current – Supply Voltage
(*)The data above is ability value of sample, it is not guaranteed. LM901family:-40[℃]～+125[℃]
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
10/17
2011.06 - Rev.B
LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR
Technical Note
●Reference Data LM2901 family LM2901 family
30 20 2V
10 0 -10 36V
5V
-20 -30 -40 -50
130
125℃
105℃
120 110 100 25℃
-40℃
90 80 70 60
-50
-25
0
25
50
75
100 125 150
0
10
AMBIENT TEMPERATURE [℃]
20
30
Fig. 76
25℃
-40℃
60 40 10
20
30
40
125
36V
100 75 5V 2V
50 25
120 100 80 60 75
-25
0
25
50
75
-40℃
2 125℃
0 -2 -4
-1
0
3
2 105℃
125℃
25℃
-40℃
1
0 -80
-60
Fig. 82
-40
-20
0
Fig. 83
Power Supply Rejection Ratio – Ambient Temperature RESPONSE TIME (HIGH TO LOW)[μs]
125℃ 105℃ 25℃ -40℃
1
3
4
5
Input Offset Voltage – Input Voltage (VCC=5V) LM2901 family
5
4
3 5mV overdrive
100mV overdrive
20mV overdrive
2
1
0 -50
-25
0
25
50
75
100 125 150
AMBIENT TEMPERATURE [℃]
Fig. 84
Response Time (Low to High) – Over Drive Voltage
Response Time (Low to High) – Ambient Temperature
(VCC=5[V],VRL=5[V],RL=5.1[kΩ])
(VCC=5[V],VRL=5[V],RL=5.1[kΩ])
LM2901 family
LM2901 family
3
2
Fig. 81
OVER DRIVE VOLTAGE [V]
4
1
INPUT VOLTAGE [V]
4
AMBIENT TEMPERATURE [℃]
5
105℃
100 125 150
5
-100
100 125 150
100 125 150
-6 -50
RRESPONSE TIME (LOW TO HIGH)[μs]
140
75
LM2901 family
RESPONSE TIME (LOW TO HIGH)[μs]
160
50
4
AMBIENT TEMPERATURE [℃]
180
2
25
LM2901 family
0
LM2901 family
50
0
25℃
Fig. 80
25
-25
6
Common Mode Rejection Ratio – Ambient Temperature
0
60
Fig. 78
Fig. 79
-25
70
Large Signal Voltage Gain – Ambient Temperature
Common Mode Rejection Ratio – Supply Voltage
-50
80
AMBIENT TEMPERATURE [℃]
150
SUPPLY VOLTAGE [V]
200
5V
15V
90
-50
40
INPUT OFFSET VOLTAGE [mV]
125℃
100
0
100
LM2901 family
COMMON MODE REJECTION RATIO [dB]
COMMON MODE REJECTION RATIO [dB]
140
80
110
Large Signal Voltage Gain – Supply Voltage
LM2901 family
105℃
36V
120
Fig. 77
160
120
130
SUPPLY VOLTAGE [V]
Input Offset Current – Ambient Temperature
POWER SUPPLY REJECTION RATIO [dB]
LARGE SINGAL VOLTAGE GAIN [dB]
LARGE SINGAL VOLTAGE GAIN [dB]
INPUT OFFSET CURRENT [nA]
140
140
40
RESPONSE TIME (HIGH TO LOW)[μs]
LM2901 family
LM2901 family
50
5
4 100mV overdrive
3 20mV overdrive 5mV overdrive
2
1
0
0 0
20
40
60
80
100
OVER DRIVE VOLTAGE [V]
-50
-25
0
25
50
75
100 125 150
AMBIENT TEMPERATURE [℃]
Fig. 85
Fig. 86
Response Time (High to Low) – Over Drive Voltage
Response Time (High to Low) – Ambient Temperature
(VCC=5[V],VRL=5[V],RL=5.1[kΩ])
(VCC=5[V],VRL=5[V],RL=5.1[kΩ])
(*)The data above is ability value of sample, it is not guaranteed. LM901family:-40[℃]～+125[℃]
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
11/17
2011.06 - Rev.B
LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR
Technical Note
●Circuit Diagram Vcc
OUT IN+
IN-
GND
Fig.87 Circuit Diagram (each Comparator)
●Measurement circuit 1 NULL Method measurement condition
Parameter
VF
S1
S2
S3
Input Offset Voltage
VF1
ON
ON
Input Offset Current
VF2
OFF OFF
VF3
OFF
ON
VF4
ON
OFF
ON
ON
Input Bias Current
VF5
Large Signal Voltage Gain
VF6
Vcc,GND,EK,VICR Unit：[V］ LM2903/LM2901 family Calculation Vcc GND EK VICR
LM393/LM339 family GND
EK
VICR
ON 5 to 30
0
-1.4
0
5 to 30
0
-1.4
0
1
ON
5
0
-1.4
0
5
0
-1.4
0
2
5
0
-1.4
0
5
0
-1.4
0
5
0
-1.4
0
5
0
-1.4
0
15
0
-1.4
0
15
0
-1.4
0
15
0
-11.4
0
15
0
-11.4
0
ON ON
Vcc
3 4
－Calculation－ 1.Input offset voltage (VIO) Vio
0.1[μF]
VF1 1+ Rf /Rs
[V] S1
2.Input offset current (IIO)
500[kΩ]
+15[V ] Ri＝ 10[kΩ]
V ICR
3.Input bias current (IIb)
RK 500[kΩ]
DUT
Ri＝ 10[kΩ]
[A]
S2
2× R i (1+ Rf / Rs)
50[kΩ]
NULL
S3
RS＝ 50[Ω]
VF4 - VF3
0.1[μF]
RS＝ 50[Ω]
[A]
Ri (1+ R f / Rs)
Ib
RK
EK
Vcc
VF2 - VF1
Iio
Rf 50[kΩ]
GND
RL
1000[pF]
-15[V ]
V VF
V RL
4.Large signal differential voltage gain (AVD) AV 20× Log
10× (1+ Rf /Rs)
Fig.88 Measurement Circuit1 (each Comparator)
[dB]
VF6 - VF5
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
12/17
2011.06 - Rev.B
LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR
Technical Note
●Measurement Circuit2 Switch Condition SW No. ―
Supply Current
SW 1
SW 2
SW 3
SW 4
SW 5
SW 6
SW 7
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Low Level Output Current
VOL=1.5[V]
OFF
ON
ON
OFF
ON
ON
OFF
Low Level Output Current
IOL=4[mA]
OFF
ON
ON
OFF
OFF
OFF
ON
High Level Output Current
VOH=36[V]
OFF
ON
ON
OFF
OFF
OFF
ON
ON
OFF
ON
ON
OFF
ON
OFF
RL=5.1[kΩ]
Response Time
VRL=5[V]
Vcc 5[V] A
－ SW1
SW2
＋ SW3
SW4
SW5
SW6
SW7
GND 0[V] RL A VIN-
VIN+
V
VRL
VOL/VOH
Fig.89 Measurement Circuit2 (each channel)
Input waveform
Input waveform
VIN
VIN over drive
+100[mV] 0[V]
0[V] +100[mV] over drive
VUOT
VUOT
Output waveform
Output waveform 5[V]
5[V]
2.5[V] 2.5[V] 0[V]
0[V] Tre LH
Tre LH
Fig.90 Response Time
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
13/17
2011.06 - Rev.B
LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR
Technical Note
●Description of Electrical Characteristics Described below are descriptions of the relevant electrical terms. Please note that item names, symbols, and their meanings may differ from those on another manufacturer’s documents. 1. Absolute maximum ratings The absolute maximum ratings are values that should never be exceeded, since doing so may result in deterioration of electrical characteristics or damage to the part itself as well as peripheral components. 1.1 Power supply voltage (Vcc/GND) Expresses the maximum voltage that can be supplied between the positive and negative power supply terminals without causing deterioration of the electrical characteristics or destruction of the internal circuitry. 1.2 Differential input voltage (VID) Indicates the maximum voltage that can be supplied between the non-inverting and inverting terminals without damaging the IC. 1.3 Input common-mode voltage range (VICR) Signifies the maximum voltage that can be supplied to non-inverting and inverting terminals without causing deterioration of the electrical characteristics or damage to the IC itself. Normal operation is not guaranteed within the input common-mode voltage range of the maximum ratings – use within the input common-mode voltage range of the electric characteristics instead. 1.4 Operating temperature range and storage temperature range (Topr,Tstg) The operating temperature range indicates the temperature range within which the IC can operate. The higher the ambient temperature, the lower the power consumption of the IC. The storage temperature range denotes the range of temperatures the IC can be stored under without causing excessive deterioration of the electrical characteristics. 1.5 Power dissipation (Pd) Indicates the power that can be consumed by a particular mounted board at ambient temperature (25°C). For packaged products, Pd is determined by maximum junction temperature and the thermal resistance. 2. Electrical characteristics 2.1 Input offset voltage (VIO) Signifies the voltage difference between the non-inverting and inverting terminals. It can be thought of as the input voltage difference required for setting the output voltage to 0V. 2.2 Input offset current (IIO) Indicates the difference of the input bias current between the non-inverting and inverting terminals. 2.3 Input bias current (IIB) Denotes the current that flows into or out of the input terminal, it is defined by the average of the input bias current at the non-inverting terminal and the input bias current at the inverting terminal. 2.4 Input common-mode voltage range (VICR) Indicates the input voltage range under which the IC operates normally. 2.5 Large signal differential voltage gain (AVD) The amplifying rate (gain) of the output voltage against the voltage difference between the non-inverting and inverting terminals, it is (normally) the amplifying rate (gain) with respect to DC voltage. AVD = (output voltage fluctuation) / (input offset fluctuation) 2.6 Supply current (ICC) Indicates the current of the IC itself that flows under specific conditions and during no-load steady state. 2.7 Low level output current (IOL) Denotes the maximum current that can be output under specific output conditions. 2.8 Low level output voltage (VOL) Signifies the voltage range that can be output under specific output conditions. 2.9 High level output current (IOH) Indicates the current that flows into the IC under specific input and output conditions. 2.10 Response time (tre) The interval between the application of input and output conditions. 2.11 Common-mode rejection ratio (CMRR) Denotes the ratio of fluctuation of the input offset voltage when the in-phase input voltage is changed (DC fluctuation). CMRR = (change of input common-mode voltage) / (input offset fluctuation) 2.12 Power supply rejection ratio (PSRR) Signifies the ratio of fluctuation of the input offset voltage when the supply voltage is changed (DC fluctuation). PSRR = (change in power supply voltage) / (input offset fluctuation)
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
14/17
2011.06 - Rev.B
LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR
Technical Note
●Derating Curves 1000 LM393PWR LM2903PWR/VQPWR
600
POWER DISSIPATION Pd [mW]
POWER DISSIPATION Pd [mW]
800
LM393PWR LM2903PWR/VQPWR
400
200
LM393DR LM2903DR/VQDR
0 0
25
50
75
100
125
150
LM339PWR LM2901PWR/VQPWR
800
LM339DR LM2901DR/VQDR
600
400
200
0 0
AMBIENT TEMPERATURE [℃]
25
50
75
100
125
150
AMBIENT TEMPERATURE [℃]
LM393DR/PWR/DGKR LM2903DR/PWR/DGKR/VQDR/VQPWR
LM339DR/PWR LM2901DR/PWR/VQDR/VQPWR
Power Dissipation
Power Dissipation
Pd[W]
θja [℃/W]
Package
Pd[W]
θja [℃/W]
SOIC8 (*8)
450
3.6
SOIC14
610
4.9
TSSOP8 (*6)
500 470
4.0
TSSOP14
870
7.0
Package
MSOP8/VSSOP8 (*7)
3.76
θja = (Tj-Ta)/Pd[℃/W]
θja = (Tj-Ta)/Pd[℃/W]
Fig.91 Derating Curves V cc
●Precautions 1) Unused circuits When there are unused circuits it is recommended that they be connected as in Fig.92, setting the non-inverting input terminalto a potential within the in-phase input voltage range (VICR).
－ ＋
2) Input terminal voltage Applying GND + 36V to the input terminal is possible without causing deterioration of the electrical characteristics or destruction, irrespective of the supply voltage. However, this does not ensure normal circuit operation. Please note that the circuit operates normally only when the input voltage is within the common mode input voltage range of the electric characteristics.
GND
Fig.92 Disable circuit example
3) Power supply (single / dual) The op-amp operates when the specified voltage supplied is between Vcc and GND. Therefore, the single supply op-amp can be used as a dual supply op-amp as well. 4) Power dissipation Pd Using the unit in excess of the rated power dissipation may cause deterioration in electrical characteristics due to a rise in chip temperature, including reduced current capability. Therefore, please take into consideration the power dissipation (Pd) under actual operating conditions and apply a sufficient margin in thermal design. Refer to the thermal derating curves for more information. 5) Short-circuit between pins and erroneous mounting Incorrect mounting may damage the IC. In addition, the presence of foreign particles between the outputs, the output and the power supply, or the output and GND may result in IC destruction. 6) Terminal short-circuits When the output and Vcc terminals are shorted, excessive output current may flow, resulting in undue heat generation and, subsequently, destruction. 7) Operation in a strong electromagnetic field Operation in a strong electromagnetic field may cause malfunctions. 8) Radiation This IC is not designed to withstand radiation. 9) IC handing Applying mechanical stress to the IC by deflecting or bending the board may cause fluctuations in the electrical characteristics due to piezoelectric (piezo) effects. 10) Board inspection Connecting a capacitor to a pin with low impedance may stress the IC. Therefore, discharging the capacitor after every process is recommended. In addition, when attaching and detaching the jig during the inspection phase, ensure that the power is turned OFF before inspection and removal. Furthermore, please take measures against ESD in the assembly process as well as during transportation and storage.
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
15/17
2011.06 - Rev.B
LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR
Technical Note
●Ordering part number
L
M
2
9
0
3
Family name LM393 LM339 LM2901 LM2903
V
Q
D
R
Operating Voltage
Package type
VQ : Tested to 32V None : Tested to 30V
D : SOIC PW : TSSOP DGK : MSOP/VSSOP
Packaging and forming specification R: Embossed tape and reel
SOIC8
4.9±0.2 (MAX 5.25 include BURR)
6
5
0.45Min.
7
3.9±0.2
6.0±0.3
8
4° +6° −4°
1
2
3
Tape
Embossed carrier tape
Quantity
2500pcs
Direction of feed
( reel on the left hand and you pull out the tape on the right hand
The direction is the 1pin of product is at the upper left when you hold
)
4
0.545
0.2±0.1
0.175
1.375±0.1
S
1.27 0.42±0.1
1pin
0.1 S
Reel
(Unit : mm)
Direction of feed
∗ Order quantity needs to be multiple of the minimum quantity.
SOIC14
8.65±0.1 (Max 9.0 include BURR)
0.65± 0.15 1
1PIN MARK
Tape
Embossed carrier tape
Quantity
2500pcs
Direction of feed
( reel on the left hand and you pull out the tape on the right hand
The direction is the 1pin of product is at the upper left when you hold
)
7
0.175± 0.075
S
+0.05 0.22 −0.03
1.375± 0.075
1.65MAX
0.515
1.05±0.2
8
6.0 ± 0.2 3.9 ± 0.1
14
4° +6° −4°
+0.05 0.42 −0.04
1.27
0.08 S 0.08 M
1pin Reel
(Unit : mm)
Direction of feed
∗ Order quantity needs to be multiple of the minimum quantity.
TSSOP8
3.0±0.1 (MAX 3.35 include BURR) 7
6
0.5 ± 0.15 3
2500pcs
Direction of feed
( reel on the left hand and you pull out the tape on the right hand
4
1PIN MARK
The direction is the 1pin of product is at the upper left when you hold
)
1.0±0.2
2
Embossed carrier tape
Quantity
+0.05 0.145 −0.03
1.0 ± 0.05
S 0.1 ± 0.05
1.2MAX
1
0.525
Tape
5
6.4 ± 0.2 4.4 ± 0.1
8
4±4
0.08 S +0.05 0.245 −0.04
0.08
M
1pin
0.65
(Unit : mm)
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
Reel
16/17
Direction of feed
∗ Order quantity needs to be multiple of the minimum quantity.
2011.06 - Rev.B
LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR
Technical Note
TSSOP14
5.0±0.1 (Max 5.35 include BURR) 4 ±4 14
1
Tape
Embossed carrier tape
Quantity
2500pcs
Direction of feed
( reel on the left hand and you pull out the tape on the right hand
The direction is the 1pin of product is at the upper left when you hold
)
7
1PIN MARK
+0.05 0.145 −0.03
0.1±0.05
S 1.0±0.05
1.2MAX
0.55
1.0±0.2
0.5±0.15
6.4±0.2 4.4±0.1
8
0.08 S +0.05 0.245 −0.04
0.65
0.08
1pin
M
Reel
(Unit : mm)
Direction of feed
∗ Order quantity needs to be multiple of the minimum quantity.
MSOP / VSSOP8
3.0±0.1 (MAX 3.35 include BURR) 6
5
0.45 ± 0.15 2
3
4
1PIN MARK
Tape
Embossed carrier tape
Quantity
2500pcs
Direction of feed
( reel on the left hand and you pull out the tape on the right hand
The direction is the 1pin of product is at the upper left when you hold
)
0.95 ± 0.2
1
+0.05 0.145 −0.03
0.525
0.1±0.05
S 0.85±0.05
1.1MAX
7
3.0 ± 0.1
4.9± 0.2
8
4±4
0.08 S +0.05 0.32 −0.04
0.08
M
1pin
0.65
(Unit : mm)
www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved.
Reel
17/17
Direction of feed
∗ Order quantity needs to be multiple of the minimum quantity.
2011.06 - Rev.B
Datasheet
Notice Precaution on using ROHM Products 1.
Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment, OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you (Note 1) , transport intend to use our Products in devices requiring extremely high reliability (such as medical equipment equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASSⅢ CLASSⅡb CLASSⅢ CLASSⅢ CLASSⅣ CLASSⅢ
2.
ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3.
Our Products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation
4.
The Products are not subject to radiation-proof design.
5.
Please verify and confirm characteristics of the final or mounted products in using the Products.
6.
In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability.
7.
De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual ambient temperature.
8.
Confirm that operation temperature is within the specified range described in the product specification.
9.
ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document.
Precaution for Mounting / Circuit board design 1.
When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability.
2.
In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice - GE
© 2014 ROHM Co., Ltd. All rights reserved.
Rev.002
Datasheet Precautions Regarding Application Examples and External Circuits 1.
If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics.
2.
You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
Precaution for Storage / Transportation 1.
Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic
2.
Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period.
3.
Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton.
4.
Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period.
Precaution for Product Label QR code printed on ROHM Products label is for ROHM’s internal use only.
Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company.
Precaution for Foreign Exchange and Foreign Trade act Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act, please consult with ROHM representative in case of export.
Precaution Regarding Intellectual Property Rights 1.
All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable for infringement of any intellectual property rights or other damages arising from use of such information or data.:
2.
No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the information contained in this document.
Other Precaution 1.
This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
2.
The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM.
3.
In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons.
4.
The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties.
Notice - GE
© 2014 ROHM Co., Ltd. All rights reserved.
Rev.002
Datasheet General Precaution
1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents. ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny ROHM’s Products against warning, caution or note contained in this document. 2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s representative.
3.
The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information.
Notice – WE
© 2014 ROHM Co., Ltd. All rights reserved.
Rev.001
