INTERNATIONAL JOURNAL OF ADAPTIVE CONTROL AND SIGNAL PROCESSING Int. J. Adapt. Control Signal Process. (2007) Published online in Wiley InterScience (www.interscience.wiley.com). DOI: 10.1002/acs.1003

Iterative learning control and repetitive control in hard disk drive industry—A tutorial YangQuan Chen1, ∗, † , Kevin L. Moore2 , Jie Yu3 and Tao Zhang4 for Self-Organizing and Intelligent Systems (CSOIS), Department of Electrical and Computer Engineering, 4160 Old Main Hill, Utah State University, Logan, UT 84322-4160, U.S.A. 2 Division of Engineering, Colorado School of Mines, Golden, CO 80401-1887, U.S.A. 3 Western Digital Technologies 20511 Lake Forest Drive, Lake Forest, CA 92630, U.S.A. 4 Seagate Technology, 1280 Disc Drive, Shakopee, MN 55379, U.S.A.

1 Center

SUMMARY This paper presents a tutorial on iterative learning control (ILC) and repetitive control (RC) techniques in hard disk drive (HDD) industry for compensation of repeatable runouts (RRO). After each tutorial, an application example is given. For ILC, a simple filtering-free implementation for written-in RRO compensation is presented. For the RC part, a new application of RC in dual-stage HDD servo is presented. Copyright q 2007 John Wiley & Sons, Ltd. Received 30 October 2006; Revised 25 June 2007; Accepted 8 August 2007 KEY WORDS:

hard disk drives; repeatable runout; non-repeatable runout; iterative learning control; repetitive; disturbance rejection; comb filter

1. INTRODUCTION Hard disk drives (HDDs) are ubiquitous and pervasive. HDDs are complex intelligent mechatronic systems/devices. Just hook up and plug-in HDDs and they will work for us reliably and efficiently. Just like electrical motors, today, we take HDDs for granted. To enhance our appreciation of the sophisticated HDD servo controls, Messner and Ehrlich [1] presented a nice tutorial on controls for disk drives. The history of HDDs servo controls has been reviewed in [2] and [3] is a textbook dedicated to HDD servo systems. To further motivate the readers, let us indicate the first fact that, as early as the year 2000, HDDs were ‘nanotech products’. For example, if a HDD has TPI (tracks per inch) of 58 000. Then, the track pitch (TP) is 25.4 mm/58 000 = 497 nm. Assuming that the track following accuracy is ∗ Correspondence

to: YangQuan Chen, Center for Self-Organizing and Intelligent Systems (CSOIS), Department of Electrical and Computer Engineering, 4160 Old Main Hill, Utah State University, Logan, UT 84322-4160, U.S.A. † E-mail: [email protected], [email protected]

Copyright q

2007 John Wiley & Sons, Ltd.

Y. Q. CHEN ET AL.

±10% of the TP, we get the nanopositioning of read/write (R/W) head with precision less than ±50 nm. Note that in [1], the highest TPI was 38 100 or 1500 tracks/mm. Today, the TPI has already been pushed beyond 100 K and steadily toward 200 K. Therefore, every HDD today is a nanotech product only from the nanopositioning point of view, not mentioning the R/W head material synthesis. The second important fact is that, there is no conventional physical sensors for sensing displacement, velocity and acceleration in HDD servo control. This is quite magic and amazing as simply shown in Figure 1 where VCM (voice coil motor), spindle motor, disk (media), R/W head are clearly shown. The key enabling technology is called ‘embedded servo’ which uses a STW (servo track writer) to lay servo bursts on the media (disk) with track and sector information embedded on the servo burst, as illustrated in Figure 2. For example, a disk drive product in the year 2000 has 288 of servo sectors with spindle speed of 5400 RPM, i.e. 90 Hz. Then, it is clear that, the sampling frequency of this drive is 90∗288 ≈ 26 kHz. Note that, the R/W head can pick up the

Figure 1. An illustrative picture of an uncovered hard disk drive.

Figure 2. Embedded servo for position sensing. Copyright q

2007 John Wiley & Sons, Ltd.

Int. J. Adapt. Control Signal Process. (2007) DOI: 10.1002/acs

ILC AND RC IN HARD DISK DRIVE INDUSTRY—A TUTORIAL

Figure 3. Embedded servo control loop.

servo burst signal in analog form and then decode it to get the position signal. The whole HDD servo control loop is shown in Figure 3. The third important fact is that the areal density, which is defined as the product of BPI (bits per inch) and TPI, of HDDs is physically limited by the superparamagnetic effect in BPI side. There is a smallest allowable magnetic grain in the media. If the grain is smaller than critical size (e.g. less than 10 nm in diameter), random thermal effects will cause the grains to de-magnetize in tens of nanoseconds and the HDD will be volatile, not non-volatile for tens of years! So, increasing TPI, also known as radial density, or track density, is preferred. However, there is also a limit on TPI. That is, the TPI cannot be too high such that the neighboring tracks could be mis-registered. Enough TMR (track mis-registration) margin has to be ensured to guarantee reliable R/W. In simple words, increasing BPI will challenge head/media material scientists and this may incur big cost while increasing TPI will simply challenge servo mechanic engineers asking for smarter servo control algorithms. This paper is an industrial tutorial on using these ‘smarter servo control algorithms’ to attack the high TPI challenge [4]. The basic objective is to reduce the head positional error signal (PES) in face of external disturbances. There are various positional error (PES) sources. Basically, two types of errors are defined: NRRO (non-repeatable runout) and RRO (repeatable runout). NRRO may be caused by PES generation noise (demodulation noise), disk vibrations, actuator arm vibrations, disk enclosure vibrations, air turbulence (windage), etc. RRO may be caused by STW error (formatting errors, non-circular eccentric tracks, also known as WIRRO (written-in RRO)), synchronized vibrations (spindle motor imperfection). In this paper, we focus on how to compensate various types of RRO in HDD servo using ILC (iterative learning control) and RC (repetitive control) techniques. This paper is organized as follows. After a brief tutorial on ILC in Section 2, we will present a simple, filtering-free type ILC application for WIRRO compensation in Section 3. Then, a brief introduction to RC is presented in Section 4 from ‘comb filter’ point of view. Section 5 is on Copyright q

2007 John Wiley & Sons, Ltd.

Int. J. Adapt. Control Signal Process. (2007) DOI: 10.1002/acs

Y. Q. CHEN ET AL.

RC for periodic disturbance attenuation in dual-stage disk drive servo systems. Finally, Section 6 concludes this tutorial paper with some remarks on future research.

2. A TUTORIAL ON ILC When we human perform a given task repeatedly, we can gain skills. Since many machines perform the same task again and again (e.g. robots, batch reactors, HDD servos, etc.), what we expect the machines to perform better and better? Can the repetitiveness be harnessed to improve the control performance of the machines? This is the main motivation of ILC. As indicated in [5], in general, a system under control may have uncertainties in its dynamic model and its environment. One attractive point in ILC is the utilization of the system repetitiveness to reduce such uncertainties and in turn to improve the control performance by operating the system repeatedly. ILC is a feedforward control strategy that updates, through iterative learning, control signals at every repeated operation. As the number of iterations increases, the system tracking error over the entire operation time period including the transient portion will decrease and eventually vanish. This may not be possible for conventional non-iterative learning control. ILC is a relatively new type of control method compared with other control methods. For example, as of December 2006, in ieeeXplore.ieee.org, using search term ‘ILC’ for all fields generates 465 papers while using ‘robust control’ generates 10 075 and 11 654 for ‘adaptive control’ and 2800 for ‘distributed control’. The term ‘ILC’ was coined by Arimoto and his associates [6] for a better control of repetitive systems. One way to describe the learning is as a process where the objective of achieving a desired result is obtained by experience when only partial knowledge about the plant is available. Therefore, as pointed out in [5], ‘learning is a bridge between knowledge and experience.’ So, roughly speaking, the purpose of introducing ILC is to utilize the system repetitions as experience to improve the system control performance even under incomplete knowledge of the system to be controlled. Based on Arimoto’s formulation, the mathematical description of ILC is as follows. • Dynamic system and control task: A general nonlinear dynamic system is considered. The system is controlled to track a given desired output yd (t) over a fixed time interval. The system is operated repeatedly and the state equation at the kth repetition is described as follows: x˙k (t) = f (xk (t), u k (t)) yk (t) = g(xk (t), u k (t))

(1)

where t ∈ [0, T ]; xk (t), yk (t) and u k (t) are state, output and control variables respectively. Only the output yk (t) is assumed to be measurable and the tracking error at the kth iteration is denoted by ek (t)yd (t)− yk (t). • Postulates: ◦ P1. Every trial (pass, cycle, batch, iteration, repetition) ends in a fixed time of duration T > 0. ◦ P2. A desired output yd (t) is given a priori over [0, T ]. Copyright q

2007 John Wiley & Sons, Ltd.

Int. J. Adapt. Control Signal Process. (2007) DOI: 10.1002/acs

ILC AND RC IN HARD DISK DRIVE INDUSTRY—A TUTORIAL

◦ P3. Repetition of the initial setting is satisfied, that is, the initial state x k (0) of the objective system can be set the same at the beginning of each iteration: x k (0) = x 0 , for k = 1, 2, . . . . ◦ P4. Invariance of the system dynamics is ensured throughout these repeated iterations. ◦ P5. Every output yk (t) can be measured and therefore the tracking error signal, ek (t) = yd (t)− yk (t), can be utilized in the construction of the next input u k+1 (t). ◦ P6. The system dynamics are invertible, that is, for a given desired output yd (t) with a piecewise continuous derivative, there exists a unique input u d (t) that drives the system to produce the output yd (t). • Controller design task: The controller design task is to find a recursive control law u k+1 (t) = F(u k (t), ek (t))

(2)

such that ek (t) vanishes as k tends to infinity. It should be noted that various research efforts can be found in the literature targeting on relaxing the above postulates (P1–P5). We do not give detailed references here, but refer the interested reader to several historical and recent surveys [7–12]. For extensive ILC tutorial slides, check [13, 14]. An illustrative toy example in the continuous-time domain is given in [15] using Arimoto’s D-type ILC updating law. Another illustrative example from HDD industry is presented in the next section where the simple ILC scheme has been practically used in mass production. A more detailed tutorial on ILC can be found in [15] with an excellent outlook on future research opportunities. To end this tutorial section, a practically important issue on ILC ‘monotonic convergence’ must be explained. The reason is clear: ‘monotonic convergence’ ensures the ILC performance to be ‘better and better’. However, conventional ILC convergence is in the sense of ‘asymptotic convergence’ which may imply that the ILC performance could be ‘better, worse, . . . and better’. Let us consider the following discrete-time single-input single-output (SISO) system: xk (t +1) = Axk (t)+ Bu k (t)

(3)

yk (t) = C xk (t)

(4)

xk (0) = x0

(5)

where A ∈ Rn×n , B ∈ Rn×1 and C ∈ R1×n are the matrices describing the system in the state space; xk (t) ∈ Rn , u k (t) ∈ R and yk (t) ∈ R are the state, input and output variables, respectively; t represents discrete-time points along the time axis; and the subscript k represents the iteration trial number along the iteration axis. Note that x k (0) = x0 for all k (ideal initial resetting). From the basic ILC theory, it is known that the ILC system is asymptotical-stable (AS) if and only if |1−h 1 |<1 with the control updating law u k+1 (t) = u k (t)+ek (t +1), where h 1 = C B with relative degree 1 and  is the learning gain [16]. Thus, it is easy to design  such that the condition |1−h 1 |<1 is satisfied provided that C and B are known exactly. However, generally it is reasonable to assume that there exist model uncertainties in C and B. In this case, it is necessary to select  considering all possible model uncertainties [17–20]. Copyright q

2007 John Wiley & Sons, Ltd.

Int. J. Adapt. Control Signal Process. (2007) DOI: 10.1002/acs

Y. Q. CHEN ET AL.

However, the existing research results are almost all restricted to the asymptotic stability (AS) problem. In ILC, it has been observed that AS may not be acceptable in practical point, because it may have very high overshoot during the transient [21]. It is very interesting to note that the ILC AS condition |1−h 1 | = |1−C B|<1 has nothing to do with the state matrix A. This is quite surprising in fact. Without knowing A, stable or unstable, ILC can still work (eventually)! This might offer a good reason to explain why ILC is getting more and more popular, but obviously there is something missing. That is the ILC transient and the related monotonic convergence issue. For technical details, please refer to [15, 17, 22].

3. A SIMPLE ILC IMPLEMENTATION IN HDD In this section, based on [23], we present a simple ILC implementation in HDD servo for compensating the WI-RRO due to STW. Due to STW servo error, the written-in tracks are no longer perfectly circular, as illustrated in Figure 4. As shown in Figure 4, the track following control block diagram contains positional disturbances d = dn +dw where dn is NRRO and dw is the WIRRO. We wish to find a compensation table dZAP such that the zigzag real track can be corrected as close to the ‘straight’, perfectly circular track or ‘the zero acceleration path (ZAP)’, as possible. Simple derivation from Figure 4 gives PESk =

1 k [r −dnk −dw −dZAP ] 1+ P(s)C(z)

(6)

where k means the kth revolution of the disk. P(s) is the plant model that is uncertain and C(z) is the known feedback stabilization controller. r is the reference signal (r = 0 for track following case).

Figure 4. Embedded servo control loop with WIRRO dw . Copyright q

2007 John Wiley & Sons, Ltd.

Int. J. Adapt. Control Signal Process. (2007) DOI: 10.1002/acs

ILC AND RC IN HARD DISK DRIVE INDUSTRY—A TUTORIAL

Since the WIRRO is repeatable from revolution to revolution, it is possible to find the best dZAP table to compensate WIRRO dw . However, since P(s) is uncertain, we use the following ILC k : method to iteratively refine the compensation table dZAP k+1 k = dZAP , +(PESk (t)) dZAP

Now the question is how to decide the idealized learning operator. Let us iterate (6), 1 k [r −dnk −dw −dZAP −(PESk (t))] 1+ P(s)C(z)   1  PESk − (d k+1 −dnk ) = 1− 1+ PC 1+ PC n

PESk+1 =

(7)

Denote the learning rate as () = 1−(()/(1+ PC))(j). Obviously, the ideal learning operator ( j) = 1+ PC Note that C(z)PESk = u kf b . The learning updating law could be simply using two available signals PES and u f b . In [23], a very simple ILC scheme is proposed as summarized in Figure 5. The ILC updating law is simply k+1 k dZAP = dZAP +rk ZPF(k , z, z −1 )[PESk + Pn (s)u f b ]

where rk is the learning gain at the kth iteration; ZPF is a low-pass zero phase filter (ZPF) with cutoff frequency k and Pn (s) is basically the nominal VCM model which is just a double integrator with a lumped actuator gain klump . It should be remarked that the above abuse of notation in ‘z’ and ‘s’ domains is for convenience only so that continuous-time and discrete-time variables and systems can be identified. On the other hand, as indicated in [22], the supervector or lifting is the only correct framework for ILC analysis. Using frequency-domain analysis of ILC convergence either in ‘z’ or in ‘s’ transfer functions, is questionable since transfer functions are obtained from the steady-state responses to sine inputs but in ILC, each iteration has a finite time duration. Note further that, PESk should be understood as PESRRO part. Our ultimate goal is to use minimum possible revolutions (revs) to learn the ZAP table. We have tried two iterations and

Figure 5. An economic implementation of ILC for compensating WIRRO. Copyright q

2007 John Wiley & Sons, Ltd.

Int. J. Adapt. Control Signal Process. (2007) DOI: 10.1002/acs

Y. Q. CHEN ET AL.

Figure 6. Before ILC (left) and after ILC WIRRO compensation (right): whole disk scanning for performance comparison.

3 revs averaging for each iteration and the results are good enough. Therefore, this simple method is attractive in the sense that only simple math operations are required. In addition, four parameters can be scheduled from iteration to iteration. They are (1) learning gain rk ; (2) cutoff frequency of the ZPF k ; (3) phase advance and (4) servo loop gain change during PES collection for average. Detailed discussions on the scheduled parameters and the advantages can be found in [23]. The ILC algorithm is summarized in the following: 1. Lower the servo loop gain and then collect 3 revs PES and Udac. Do averaging. Get PES a and Udac a. 2. Demean Udac a and then double integrate it. Get Udac II. 3. ZAP table 1=(PES a+Klump* Udac II)*Learning Gain 1. 4. ZPF for the first ZAP table 1 (NOTE: ZAP table 0=0). 5. Repeat (1) with an increased servo-loop gain. 6. Repeat (2). 7. ZAP table 2=ZAP table 1+(PES a+Klump*Uda II)*Learning Gain 2. 8. Set servo-loop gain to normal. The drive level results are illustrated in Figure 6 where left four subplots are for the case of no WIRRO compensation and the right four subplots are for the case of after WIRRO compensation. In each case, four subplots are presented with (1) SNR: 1(RRO)/1(NRRO); (2) RRO: (1) percent TP; (3) RV: total runout value (RV); and (4) NRRO. (1) Obviously, NRRO remains almost the same before and after compensation. Typical time-domain traces are shown in Figure 7. Upper subplots are PES signals and the bottom subplots are for the actuator DAC signal. Clearly, after ILC compensation, the actuator follows a more straight path resulting less actuation. To end this section, besides numerous RRO compensation-related patents, we wish to point out several recent papers on using ILC for RRO compensation in HDD servo [24–26] where new modifications and more systematic designs are presented. Copyright q

2007 John Wiley & Sons, Ltd.

Int. J. Adapt. Control Signal Process. (2007) DOI: 10.1002/acs

ILC AND RC IN HARD DISK DRIVE INDUSTRY—A TUTORIAL

Figure 7. Before ILC (left) and after ILC WIRRO compensation (right): time-domain traces.

4. A BRIEF TUTORIAL ON RC In ieeeXplore.ieee.org, using search term ‘RC’ for all fields generates 258 papers. Compared with ILC, this number is about half. The basic idea of RC is to use a delay line to generate the internal model of the periodic disturbance of period N as illustrated in Figure 8. In the ideal case, we can set Q(z −1 ) = 1. Then, the gain block before C(z −1 ) block is simply 1+ z −N /(1− z −N ) = 1/(1− z −N ). The Bode plot of 1/1− z −N is shown in Figure 9, which is a ‘comb’. In fact, RC block diagram (Figure 8) can be equivalently drawn in the comb filter form, as shown in Figure 10. Therefore, as indicated in [27], RC is nothing but a kind of comb filter. Observe that, the overall controller gain C  (z −1 ) =

1 C(z −1 ) 1− Q(z −1 )z −N

has multiple peaks (high gain) at the integer multiples of the harmonic frequency of the periodic disturbance. The sensitivity function S = 1/(1+C  P) will have multiple deep dips or notches. Therefore, the harmonics in the disturbances can be ‘combed’ out. This is the desirable disturbance rejection or attenuation property from using RC in HDD servo systems. Two good reviews of RC can be found in [28, 29]. In HDDs, the patent [30] offers many other variations on economic or parsimonious implementations. In [31], some excellent drive level RC results can be found. Note that, for HDD servo, it is normally believed that RC is for attacking harmonics of spindle frequency (90 Hz for 5400 RPM drives). However, as shown in [31] (slides Copyright q

2007 John Wiley & Sons, Ltd.

Int. J. Adapt. Control Signal Process. (2007) DOI: 10.1002/acs

Y. Q. CHEN ET AL.

Q(z -1)z -N/(1-Q(z -1z -N)

+

r=0

C(z -1)

+

P(s)

+

_

Figure 8. Repetitive control with a Q-filter, internal-model form.

140

120

100

dB

80

60

40

20

0 −20

0

1000

2000

3000

4000 5000 frequency (Hz)

6000

7000

8000

9000

Figure 9. Bode magnitude plot of 1/(1− z −N ) (N = 100, sampling frequency is 9000 Hz).

192, 193), when implemented properly, arbitrary fundamental frequency can be achieved. Another remark is that, Q-filter is a low-pass filter to limit the effective bandwidth of the RC. Q-filter can be (and should be) non-causal. Just a reminder that ILC and RC are mostly similar with only one important difference. In ILC, we need resetting to the same initial conditions. In RC, however, there is no resetting. RC is continuous along time axis with no extra mechanism to return to the same initial condition. Copyright q

2007 John Wiley & Sons, Ltd.

Int. J. Adapt. Control Signal Process. (2007) DOI: 10.1002/acs

ILC AND RC IN HARD DISK DRIVE INDUSTRY—A TUTORIAL

Q(z -1)z -N

r=0 +

+

+ C(z -1)

P(s)

_

Figure 10. Repetitive control with a Q-filter, comb filter form.

In the next section, we will present more technical details on RC with an emphasis on dual-stage HDD servo systems.

5. RC FOR PERIODIC DISTURBANCE ATTENUATION IN DUAL-STAGE DISK DRIVE SERVO SYSTEMS 5.1. Background In many motion control systems, the desired references or external disturbances include periodic signals with a known time period. Iterative learning and repetitive control (IRC/RC) techniques are often used for the periodic signal learning to achieve zero tracking error. RC has been investigated extensively because of its practicality and applicability ([32–38], and the references therein). It is well known that the RC is based on Internal-Model Principle (IMP) [39]. The algorithm repetitively applies a learning controller to a plant to achieve trajectory tracking or disturbance attenuation. The tracking error is reduced with each repetition and eventually, a perfect tracking control can be achieved. Many successful applications of iterative learning and RC have been found in motion control including HDDs and optical disk drives [33–36] and many other servo control systems [40–45]. In this section, we investigate the application of RC technique to the problem of periodic disturbance attenuation in dual-stage HDD control systems. Owing to windage, mechanical resonance, spindle motion and disc flutters, HDD servo systems contain both repeatable and non-repeatable disturbances appearing in the PES. In frequency domain, a RRO disturbance occurs at frequencies that are integer multiples of the disk rotation frequency. It is a considerable source position error with respect to the center of the data track. To meet the TMR requirement for high TPI products, the periodic disturbance must be attenuated to improve the servo tracking performance. Figure 11 shows a dual-stage HDD servo system. Gvcm and Gpzt denote VCM and microactuator model, respectively. Cvcm and Cpzt are controllers for VCM actuator and Piezo microactuator, respectively. PES is the error between head position and the reference signal. d nrro represents the total non-repeatable disturbances such as measurement noises, disk flutter, windage affects, etc., d rro represents the repeatable disturbances due to spindle motion, and W rro denotes the written-in error on servo tracks. Generally speaking, there are two types of techniques for repeatable disturbance attenuation. For RRO caused by spindle motor and disk movement, adaptive feedforward compensation (AFC) Copyright q

2007 John Wiley & Sons, Ltd.

Int. J. Adapt. Control Signal Process. (2007) DOI: 10.1002/acs

Y. Q. CHEN ET AL.

Figure 11. Dual-stage HDD control system.

technique is usually used to reject the disturbances [46]. For written-in errors generated in servo writing, WI-RRO, a possible approach is called the ZAP concept, which uses a feed-forward profile created by learning techniques such as ILC/RC schemes. The WI-RRO is compensated such that the servo system does not respond to the written-in disturbance. 5.2. Control structure In HDDs, the RRO in low harmonic frequencies is caused by the disk vibration or spindle motor. The RRO amplitude and phase of the first several low-frequency harmonics are time varying and usually compensated by AFC. Hence, we separate the W rro into the following two parts: W rro = W + W0

(8)

where W0 = W rro(), ∀0 denotes the low-frequency repeatable disturbances to be handled by other feedforward methods; W represents the written-in error to be controlled by repetitive algorithm W = W rro() ∀ > 0

(9)

d = d nrro+d rro+ W0

(10)

G = Cvcm G vcm +Cpzt G pzt

(11)

Define

A RC structure is proposed in Figure 12. K (z) and Q(z) are the RC filters, N is the time period of one revolution and Wˆ is the estimation of W . The control objective is to design suitable filters K (z) and Q(z), such that the estimate Wˆ converges to W and the tracking error e is minimized. From Figure 12, we have Wˆ (z) = Q(z)z −N [Wˆ (z)+e(z)K (z)]

(12)

Therefore, −N

z Q(z)K (z) e(z) Wˆ (z) = 1− z −N Q(z) Copyright q

2007 John Wiley & Sons, Ltd.

(13)

Int. J. Adapt. Control Signal Process. (2007) DOI: 10.1002/acs

ILC AND RC IN HARD DISK DRIVE INDUSTRY—A TUTORIAL

Figure 12. A repetitive control of HDD system.

In track following case, R(z) = 0, the closed-loop error system is e(z) = Wˆ (z)− W (z)−d(z)−e(z)G(z)

(14)

W (z)+d(z) z −n Q(z)K (z) e(z)− −N [1+ G(z)][1− z Q(z)] 1+ G(z)

(15)

By using (13), we have e(z) = Hence

  K (z) 1− z −N Q(z) e(z)z −N − [W (z)+d(z)] e(z) = Q(z) 1+ 1+ G(z) 1+ G(z)

(16)

Since N is the one revolution period, we have ei−1 (z) = z −N ei (z) and di−1 (z) = z −N di (z) with the revolution number i. Equation (16) can be expressed as   K (z) di −di−1 Q(z) Wi − Wi−1 Q(z) ei (z) = Q(z) 1+ ei−1 (z)− − (17) 1+ G(z) 1+ G(z) 1+ G(z) In order to cancel the repeatable disturbance W , we select Q(z) as a ZPF with unity gain 1 at the harmonic frequencies for all  > 0 . This implies that Wi − Wi−1 Q(z) = 0 Define



K () () = Q() 1+ 1+ G()

 (18)

Then, (17) can be further written as ei = ()ei−1 −

di −di−1 Q() 1+ G()

(19)

By iterating (19), ei = 2 ()ei−2 −() Copyright q

2007 John Wiley & Sons, Ltd.

di−1 −di−2 Q() di −di−1 Q() − 1+ G() 1+ G()

(20)

Int. J. Adapt. Control Signal Process. (2007) DOI: 10.1002/acs

Y. Q. CHEN ET AL.

Further iterating (20), and defining d¯ the upper bound of noise di , ∀i0, we have   i   1+Q()   m i  d¯  ei    ()e0 +  ()  1+ G()  m=0   1+Q()  1−i+1 ()  i   d¯   ()e0 + 1−()  1+ G()  To guarantee the convergence, the following condition is required:   K () () = Q() 1+ <1 ∀s /2 1+ G()

(21)

(22)

where s is the sampling frequency. 5.3. RC filter design using dual-stage loop-shaping From (22), we can see that the convergence rate depends on the selection of filters Q(z) and K (z). In ideal case, if the filter K (z) can be selected as K () = −[1+ G()]

∀0 <s /2

(23)

Then, () = 0

∀0 <s /2

(24)

This implies the convergence can be achieved in one iteration. In practice, it is not possible to design a filter satisfying this condition due to model uncertainties. Individual frequency components of the error signal can exhibit different convergence rates depending upon () evaluated at those frequencies [45]. Over the interested frequency range, a fast convergence is achieved with a learning filter K (z) designed as an approximation to the inverse sensitivity function K () ≈ −[1+ G()]

∀0 <s /2

(25)

An interesting work in [23] shows a design using the knowledge of a nominal plant model and the control signal in order to construct the approximation of the inverse sensitivity function. There are several other methods for determining a stable approximation to the system inverse sensitivity [40, 47]. In HDD dual-stage servo systems, the additional actuator gives a significant freedom to shape the servo loop. This provides an opportunity to design a special dual-stage controller for improved RC ZAP process. The design concept is that synthesizing a servo controller such that the closed-loop sensitivity function satisfies 1 ≈1 1+ G()

∀0 <s /2

(26)

This is highly feasible because the frequency 0 is usually low and dual-stage servo system can achieve high bandwidth. A special servo loop can be selected by synthesizing a low bandwidth open-loop servo system with high gain and phase margin, which results in a flat gain response of closed-loop sensitivity such that (26) is satisfied. In this case, we can simply choose the RC filter Copyright q

2007 John Wiley & Sons, Ltd.

Int. J. Adapt. Control Signal Process. (2007) DOI: 10.1002/acs

ILC AND RC IN HARD DISK DRIVE INDUSTRY—A TUTORIAL

K (z) = −1. This implies that no modeling work is necessary. It greatly simplifies the repetitive controller design and implementation. It should be mentioned that the above low bandwidth dual-stage system is running during repetitive learning process only. Once the desired RRO compensation profile is obtained, it will be frozen and written to the disk. During normal drive operation, the ZAP profile will be loaded from disc at each servo sample, and a normal bandwidth dual-stage servo system will be used to achieve better seek and tracking performance. As we mentioned in Section 5.2, RRO at the first several harmonic frequencies are usually compensated by AFC scheme. In order to remove the components of these harmonic frequencies from the profile of repetitive controller, the ZPF Q(z) must have enough attenuation in the frequency range 0 . This also helps to solve the possible conflict of running AFC and RC algorithm in the same frequency range. 5.4. Drive level results The proposed RC algorithm has been tested on Seagate 10KRPM Cheetah drives. The harmonic frequency of the product is 166.7 Hz. The sample rate is 48 kHz. Since the first three harmonic frequencies are handled by AFC, the RC algorithm will cover the frequency range 666.7 f 24 000 Hz. A high-pass filter Q(z) is selected as follows Q(z) = 

z 2 −1.996z +0.996 z 2 −1.825z +0.8326

(27)

where  = 13 . A low bandwidth dual-stage controller is designed to achieve 1/[1+ G(z)] close to 1 in the frequency range 666.7  f 24 000 Hz. Figure 13 plots the frequency response of the dual-stage open-loop G(z). It is shown that the bandwidth is around 670 Hz with a gain margin of 18 dB,

Figure 13. Low-bandwidth open-loop dual-stage system. Copyright q

2007 John Wiley & Sons, Ltd.

Int. J. Adapt. Control Signal Process. (2007) DOI: 10.1002/acs

Y. Q. CHEN ET AL.

Figure 14. Sensitivity of low bandwidth dual-stage system for repetitive control application.

Figure 15. RRO History of repetitive control process.

and a phase margin of 55◦ . The resulting sensitivity 1/(1+ G) is plotted in Figure 14. It is shown that the sensitivity is very close to 1 in the RRO ZAP frequency range 667–24 000 Hz. Figure 15 shows the time history of RRO reduction during the repetitive control process. It is shown that the RRO drops from 12% of TP to 3% after 10 iterations (2880 sectors). Figure 16 shows the frequency-domain RRO comparison. We see that most of the RRO harmonics decreases after applying the RRO compensation profile. Figure 17 shows the experimental results of RRO improvement with and without RC ZAP. We can see that without ZAP, the RRO 3-sigma is 1.0 inches at OD tracks and 0.85 inches at ID Copyright q

2007 John Wiley & Sons, Ltd.

Int. J. Adapt. Control Signal Process. (2007) DOI: 10.1002/acs

ILC AND RC IN HARD DISK DRIVE INDUSTRY—A TUTORIAL

Figure 16. Frequency-domain comparison of RRO before and after ZAP (10 iterations).

Figure 17. RRO Improvement with/without repetitive control ZAP.

tracks. The RRO 3-sigma drops to 0.2596 inches in average when applying the RC algorithm. The iteration numbers used on each track are about 6.4 in average. 6. CONCLUDING REMARKS In plain language, this paper explained why hard disk drive (HDD) servo control is challenging and exciting. We focused on how to reject the repeatable runouts in HDD servo. A tutorial on Copyright q

2007 John Wiley & Sons, Ltd.

Int. J. Adapt. Control Signal Process. (2007) DOI: 10.1002/acs

Y. Q. CHEN ET AL.

iterative learning control (ILC) with a simple application/implementation in HDDs without any filtering operation. Drive-level results are presented for illustration. For RC, the tutorial, although brief, is presented from ‘comb filter’ point of view. Detailed RC techniques in HDD industry for compensation of repeatable runouts are presented for dual-stage HDD servo. In summary, ILC/RC techniques have been playing important roles in modern HDD servos. Although there are many issues and challenges in implementations, ILC/RC can be considered as matured, established techniques for repeatable disturbance rejection. The rationale is clear: whenever the disturbance is deterministic and reoccurring, it can be rejected.

REFERENCES 1. Messner W, Ehrlich R. A tutorial on controls for disk drives. Proceedings of 2001 American Control Conference, Arlington, VA, U.S.A. AACC: 2001; 408–420. 2. Abramovitch D, Franklin G. A brief history of disk drive control. IEEE Transactions on Automatic Control 2002; 22(3):28–42. 3. Chen BM, Lee TH, Peng K, Venkataramanan V. Hard Disk Drive Servo Systems (2nd edn). Advances in Industrial Control. Springer: Berlin. ISBN: 1846283043, June 2006. 4. Chen YQ, Moore KL, Yu J, Zhang T. Iterative learning control and repetitive control in hard disk drive industry—a tutorial. Proceedings of the IEEE International Conference on Decision and Control (CDC), San Diego, U.S.A. IEEE: Silver Spring, MD, December 2006; 1–15. 5. Chen YQ, Wen C. Iterative Learning Control: Convergence, Robustness and Applications. Lecture Notes Series on Control and Information Science, vol. 248. Springer: London, 1999. 6. Arimoto S, Kawamura S, Miyazaki F. Bettering operation of robots by learning. Journal of Robotic Systems 1984; 1:123–140. 7. Moore KL, Dahleh M, Bhattacharyya SP. Iterative learning control: a survey and new results. Journal of Robotic Systems 1992; 9(5):563–594. 8. Moore KL. Iterative Learning Control for Deterministic Systems. Advances in Industrial Control. Springer: Berlin, 1993. 9. Chen YQ. High-order iterative learning control: convergence, robustness and applications. Ph.D. Thesis, Nanyang Technological University, 1997. 10. Moore KL. Iterative learning control—an expository overview. Applied and Computational Controls, Signal Processing, and Circuits 1999; 1(1):151–241. 11. Ahn HS, Chen YQ, Moore KL. Iterative learning control: brief survey and categorization 1998–2004. IEEE Transactions on Systems, Man, and Cybernetics, Part-C 2007, in press. 12. Bristow DA, Tharayil M, Alleyne AG. A survey of iterative learning control: a learning-based method for high-performance tracking control. IEEE Control Systems Magazine 2006; 26(3):96–114. 13. Moore KL. Iterative learning control international summer school at Utah State University. http://www.ece. usu.edu/csois/ilc/summerschool03/, June 2003. 14. Moore KL, Chen YQ. Iterative learning control tutorial. Workshop at 2006 International Conference on Mechatronics and Automation, Luoyang, China, http://egweb.mines.edu/faculty/kmoore/talks.htm, June 2006. 15. Moore KL, Chen YQ, Ahn H-S. Iterative learning control: a tutorial and a big picture. Proceedings of the 2006 IEEE International Conference on Decision and Control (CDC), San Diego, U.S.A. IEEE: Silver Spring, MD, December 2006; 1–6. 16. Moore KL. On the relationship between iterative learning control and one-step ahead minimum prediction error control. Proceedings of the Asian Control Conference, Shanghai, 2000; 1861–1865. 17. Ahn H-S. Robust and adaptive learning control design in the iteration domain. Ph.D. Thesis, Utah State University, UT, February 2006. 18. Xu J-X, Viswanathan B, Qu Z. Robust learning control for robotic manipulators with an extension to a class of non-linear systems. International Journal of Control 2000; 73(10):858–870. 19. De Roover D, Bosgra OH. Synthesis of robust multivariable iterative learning controllers with application to a wafer stage motion system. International Journal of Control 2000; 73(10):968–979. Copyright q

2007 John Wiley & Sons, Ltd.

Int. J. Adapt. Control Signal Process. (2007) DOI: 10.1002/acs

ILC AND RC IN HARD DISK DRIVE INDUSTRY—A TUTORIAL

20. Mezghani M, Roux G, Cabassud M, Dahhou B, Le Lann MV, Casamatta G. Robust iterative learning control of an exothermic semi-batch chemical reactor. Mathematics and Computers in Simulation 2001; 57(6):367–385. 21. Longman RW. Iterative learning control and repetitive control for engineering practice. International Journal of Control 2000; 73(10):930–954. 22. Ahn H-S, Moore KL, Chen YQ. Iterative Learning Control: Robustness and Monotonic Convergence for Interval Systems. Communications and Control Engineering. Springer: London, ISBN: 978-1-84628-846-3, June 2007. 23. Chen Y, Tan L, Ooi K, Bi Q, Cheong K. Repeatable runout compensation using a learning algorithm with scheduled parameters. US Patent 6,437,936, 2002. 24. Jia Q-W, Wang Z-F, Wang F-C. Repeatable runout disturbance compensation with a new data collection method for hard disk drive. IEEE Transactions on Magnetics 2005; 41(2):791–796. 25. Graham MR, de Callafon RA. An iterative learning design for repeatable runout cancellation in disk drives. IEEE Transactions on Control Systems Technology 2006; 14(3):474–482. 26. Melkote H, Wang Z, McNab RJ. An iterative learning controller for reduction of repetitive runout in disk drives. IEEE Transactions on Control Systems Technology 2006; 14(3):467–473. 27. Chen YQ. Iterative learning control (ILC) and repetitive learning control (RLC) are special applications of comb filter (CF), http://www.ece.usu.edu/csois/ilc/ILC/comb filter/index.htm, October 1999. 28. Hillerstr¨om G, Walgama K. Repetitive control theory and applications—a survey. Proceedings of the 13th IFAC World Congress, San Francisco, U.S.A., vol. D. IFAC, July 1996; 1–6. 29. Cuiyan L, Dongchun Z, Xianyi Z. A survey of repetitive control. Proceedings of the IEEE/RSJ International Conference on Intelligent Robots and Systems (IROS 2004). IEEE: Silver Spring, MD, 28 September–2 October 2004; 1160–1166. 30. Chen YQ, Ding M, Xiu L, Ooi KK, Tan LL. Optimally designed parsimonious repetitive learning compensator for hard disc drives having high track density. US Patent 6,574,067, 2003; 1–13. 31. Chen YQ. Parsimonious ILC and RC: seagate experience, http://www.ece.usu.edu/csois/ilc/summerschool03/ ILC ISS 03 Chen.pdf, June 2003. 32. Hara S, Yamamoto Y, Omata T, Nakano M. Repetitive control-system—a new type servo system for periodic exogenous signals. IEEE Transactions on Automatic Control 1988; 33:659–668. 33. Chew KK, Tomizuka M. Digital control of repetitive errors in disk drive systems. IEEE Control System Magazine 1990; 10(1):16–20. 34. Onuki Y, Ishioka H. Compensation for repeatable tracking errors in hard drives using discrete-time repetitive controller. IEEE/ASME Transactions on Mechatronics 2001; 6(2):132–136. 35. Moon J-H, Lee M-N, Chung M-J. Repetitive control for the track-following servo system of an optical disk drive. IEEE Transactions on Control System Technology 1998; 6(2):663–670. 36. Tomizuka M. Zero-phase error tracking algorithm for digital control. ASME Journal of Dynamic Systems, Measurement, and Control 1987; 109:65–68. 37. Garimella SS, Srinivasan K. Transient response of repetitive control systems. Proceedings of 1994 American Control Conference, Baltimore, MD, U.S.A. AACC, 1994; 2909–2913. 38. Tsao T-C, Tomizuka M, Chew K. Discrete-time domain analysis and synthesis of repetitive controllers. ASME Journal of Dynamic Systems, Measurement, and Control 1988; 110:271–280. 39. Francis BA, Wonham WM. The internal model principle of control theory. Automatica 1976; 12:457–465. 40. Graham MR, de Callafon RA, Shrinkle L. An iterative learning controller for reduction of repeatable runout in hard disk drives. Proceedings of 2006 American Control Conference, Minneapolis, MN, U.S.A. AACC: 2006; 576–581. 41. Broberg HL, Molyet RG. Plug in repetitive control for industrial robotic manipulators. Proceedings of the IEEE International Conference on Robotics and Automation, Cincinnati, OH. AACC, 1990; 1970–1975. 42. Zhou K, Wang D, Low K-S. Periodic errors elimination in CVCF PWM DC/AC converter systems: repetitive control approach. IEE Proceedings—Control Theory and Applications 2000; 147:694–700. 43. Hillerstrom G, Sternby J. Application of repetitive control to a peristaltic pump. ASME Journal of Dynamic Systems, Measurement, and Control 1994; 116(1):786–789. 44. Owens DH, Rogers E, Galkowski K. Control theory and applications for repetitive processes. Advances in Control Highlights of ECC’99 1999; 2(3):327–333. 45. Longman RW. Iterative learning control and repetitive control for engineering practice. International Journal of Control 2000; 73(10):930–954. 46. Bodson M, Sacks A, Khosla P. Harmonic generation in adaptive feedforward cancellation schemes. IEEE Transactions on Automatic Control 1994; 39(9):1939–1944. 47. Ljung L. System Identification: Theory for the User. Prentice-Hall: Upper Saddle River, NJ, 1999. Copyright q

2007 John Wiley & Sons, Ltd.

Int. J. Adapt. Control Signal Process. (2007) DOI: 10.1002/acs

Iterative learning control and repetitive control in ... - Semantic Scholar

shown in Figure 1 where VCM (voice coil motor), spindle motor, disk (media), ...... Proceedings of the IEEE International Conference on Decision and Control ...

685KB Sizes 8 Downloads 405 Views

Recommend Documents

Iterative learning control and repetitive control in ... - Semantic Scholar
sophisticated HDD servo controls, Messner and Ehrlich [1] presented a nice tutorial on controls for disk ... Electrical and Computer Engineering, 4160 Old Main Hill, Utah State ... For example, a disk drive product in the year 2000 ... simple words,

Experiments in learning distributed control for a ... - Semantic Scholar
Aug 28, 2006 - Institute for Aerospace Studies, University of Toronto, 4925 Dufferin .... This may be done by way of a set of basis behaviours ..... We call the modified .... ings of IEEE International Conference on Evolutionary Computation,.

Counteractive Self-Control - Semantic Scholar
mained in the distance? ... tempt individuals to stray from otherwise dominant long-term ... bach, University of Chicago, Booth School of Business, 5807 South.

Cooperative Control and Potential Games - Semantic Scholar
Grant FA9550-08-1-0375, and by the National Science Foundation under Grant. ECS-0501394 and Grant ... Associate Editor T. Vasilakos. J. R. Marden is with the ... J. S. Shamma is with the School of Electrical and Computer Engineer- ing, Georgia ......

Cooperative Control and Potential Games - Semantic Scholar
However, we will use the consensus problem as the main illustration .... and the learning dynamics, so that players collectively accom- plish the ...... obstruction free. Therefore, we ..... the intermediate nodes to successfully transfer the data fr

The role of consciousness in cognitive control and ... - Semantic Scholar
May 7, 2012 - motor responses earlier (have a faster time-course) than primes that are ...... and Henson, R. N. (2009). ..... April 2012; published online: 07 May.

Iterative Learning Control: Brief Survey and Categorization - IEEE Xplore
Index Terms—Categorization, iterative learning control (ILC), literature review. ... introduction to ILC and a technical description of the method- ology. In Section II ...

Neurocognitive mechanisms of cognitive control - Semantic Scholar
Convergent evidence highlights the differential contributions of various regions of the prefrontal cortex in the service of cognitive control, but ..... Presentation of a stop-signal yields a rapid increase in activity in FEF gaze-holding neurons and

VISION-BASED CONTROL FOR AUTONOMOUS ... - Semantic Scholar
invaluable guidance and support during the last semester of my research. ..... limits the application of teach by zooming visual servo controller to the artificial ... proposed an apple harvesting prototype robot— MAGALI, implementing a spherical.

predictive control of drivetrains - Semantic Scholar
GPS and road maps containing information about road bends, speed limits and topogra- phies. ¯ traffic information obtained by external sour- ces. ¯ on-board ... optimization problem. However, this leads to an extraordinary high computational effort

VISION-BASED CONTROL FOR AUTONOMOUS ... - Semantic Scholar
proposed an apple harvesting prototype robot— MAGALI, implementing a ..... The software developed for the autonomous robotic citrus harvesting is .... time network communication control is established between these computers using.

Iterative Learning Control for Optimal Multiple-Point Tracking
on the system dynamics. Here, the improved accuracy in trajectory tracking results has led to the development of various control schemes, such as proportional ...

Achieving distributed user access control in sensor ... - Semantic Scholar
networks, in: IEEE Symposium on Security and Privacy, Oakland, CA,. 2004 (May). Haodong Wang is an assistant professor of. Computer and Information Science at Cleve- land State University. He received his PhD in. Computer Science at College of Willia

Topology Control of Dynamic Networks in the ... - Semantic Scholar
planets outside our own solar system, will rely on FF to achieve ... energy consumption in the network. .... the consumption of fuel and energy is also crucial for.

Topology Control of Dynamic Networks in the ... - Semantic Scholar
enabling technology for future NASA space missions such ... In mobile sensor networks, there ... preserving connectivity of mobile networks [5], [9], [14],. [15], [20] ...

Circadian control of neural excitability in an animal ... - Semantic Scholar
The gaps in the firing rate data (around day 5 in both control and latent period) reflect the .... the Wilder Center of Excellence for Epilepsy Research, and the Chil-.

Terminal Iterative Learning Control with Multiple ...
Jul 1, 2011 - School of Mechatronics, Gwangju Institute of Science and ... (GIST) - 2011 American Control Conference, San Francisco, California, USA, 2011.

Local Area Networks and Medium Access Control ... - Semantic Scholar
Multiple Access Communication: Examples. Satellite Channel. = fin. = fout. Multidrop telephone lines. Inbound line. Outbound line. Examples (2). Ring networks.

software and control architecture development of ... - Semantic Scholar
to achieve this objective with a typical laptop computer elimi- nates the cost .... frequency of 10 Hz, even though they are calculated at a much higher rate in the ...

Dynamics Based Control and Continual Planning - Semantic Scholar
time-line. It is hoped that analytical tools will assist (PO)MDPs to become more ... Although the analytical properties of the system description allow control the-.

Joint Scheduling and Power Control for Wireless ... - Semantic Scholar
This is further aggravated in ad-hoc networks since all nodes are mobile ..... Go to next slot i = i + 1 .... We compare the structure of the power control problem.

Topology and Control Innovation for Auxiliary ... - Semantic Scholar
LED lighting applications will require forced-air convection because of the high intensity of light needed such as recessed light, spot light and track light. Regular fans, however, introduce life time and reliability concern and for indoor applicati

Dynamics Based Control and Continual Planning - Semantic Scholar
us to create a great variety of visual effects applied and utilised by Computer. 2This is, in fact, .... to what degree the system is controllable, that is, what kind of behaviours it is possible to ...... Computer Science, University of California a

Somatotype and schizophrenia. A case-control study - Semantic Scholar
taining increasing interest in the recent psychiatric litera- ture. ... Hospital Universitario de Vall d'Hebron ... cute and day care hospital units in in-hospital regime.