Welcome to OMNI

M-505 3D Printer Install Manual

Contact：Cora Lee Skype: cora8809

Note: 



 



1, Please ensure that the package is intact before signing;

2, After unpacking, please confirm the package and quantity is consistent with enclosed packing list; 3, Please be carefull when you assemble; 4, Please use sandpaper or knife to fix if both end of rod doesn't smooth; 5, Before you connect power, please make confirm all wires connected well;



6, Please don't try to change the firmware alone;



7, Any problems, please don't hesitate to contact us.

All Parts as below

Step 1：Check all Arylic Parts and take out the paper.

Step 2：Framework Assembly Parts：A*1，B*1，C*1，M3*18 screw*8，M3 nut*8.

Ps: A is Left and B is Right. Pre-Installation

A

B C

After installation

A

B C

Step 3：Framework Fixed and Z-axis motor support Assemble Parts：H1*1, H2*1, D*1, I1*1, I2*1, J1*1, J2*1, J3*1, J4*1, M3*18 svcrew*20, M3 nuts*10. After installation Pre-Installation

Step 4： Y axis Screw Arbors Assemble Parts：E*1, M8*400MM screw arbors*2, M8 nuts*12, M8 cushion ring*12. After installation Pre-Installation

Step 5： Y axis Front Base Frame Assemble Parts：F*1, U*4, M3*18 screw*4, M3 nuts*4. After installation Pre-Installation

Step 6：Y axis Rod Assemble Parts：K*2, M8*380MM sliding rod*2, Bearing*3, M3*18 screws*2, M3 nuts*2.

Pre-Installation

After installation

Step 7：Y axis Belt and Z axis's Limited switch Fixed Assemble Parts：L*1, M*1, R*2, P*2, M3*18 screws*5, M3*30 screws*2, M3 nuts*7. Pre-Installation After installation

Step 8：Y axis Motor and Z axis Motor Assemble Parts：O*1, Q*1, Z axis Motor*2, Y axis Motor*1, Belt*70cm, M3*10 Inner hexagon screws*12, M3*18 screws*4, M3 nuts*4. After installation Pre-Installation

Step 9：Hot Bed Assemble Parts：Hot Bed*1，Aluminium plate*1, M3*30 screws*4, M3 nuts*4, Compression springs*4, Thumb nuts*4. After installation Pre-Installation

Step 10：Z axis Rod Assemble Parts：M8*363mm sliding rod*2, M8*325mm screw arbors*2, M8*435mm sliding rod*2, Print Parts*2, Bearing*3. Pre-Installation

After installation

Step 11：Extruder Assemble Parts：U-Metal plate*1, S*4， Extruder Motor*1 set, 40*40*10 Fan*1, M3*18 screws*8, M4*8 screws*12, M3*20 Inner hexagon screws*3. 2 extra screw for Fan. Pre-Installation After Installation

Step 12: X axis Motor and Belt Assemble Parts：X axis Motor*1, Belt*90cm, M3*20Inner hexagon screws*3, M3*18 screws*2, M3 nuts*2.

Step 13：Limited Switch Assemble Parts：X axis Limited Switch *1, Y axis Limited Switch *1, Z axis Limited Switch *1.

Step 14：LCD Screen Assemble Parts：LCD Screw*1, Screen Cover*1, M3*18 screws*4, M3 nuts*4, Plastic Pillars*4. Pre-Installation After installation

Step 15：Power Supply Assemble Parts：Power supply*1, Power cable*1, Power Plug*1, M3*12 screws*3.

Ps：Default EU Plug Pre-Installation

After installation

Step 16：Mainboard Assemble Parts：Mainboard*1, M3*30 screw*4, M3 nut*4, Plastic Pillars*4.

Step 17：Feeding Frame Assemble Patrs：V*1, W*1, X*2, M8 nuts*4, M3*18 screws*4, M3 nuts*4. Pre-Installation

After installation

Complete Finish

All comments are welcome! Thank you very much!