No. of Printed Pages : 4

I MSEE-004 I

POST GRADUATE DIPLOMA IN FIRE SAFETY 0\ AND DISASTER MANAGEMENT (PGDFSTYDM)

o Term-End Examination December, 2011 MSEE-004 : MANUFACTURING PROCESS INDUSTRIES Time : 3 hours

Maximum Marks : 100

Note : Section-I Answer all questions, carry equal marks. Section-II Answer any 6- all questions carry equal marks. Section-III Answer any 2- carry 25 marks each. SECTION - I (2 marks each) 1.

A risk and a hazard are the same thing. Yes/No

2.

Noise does not represent a risk below about 90 dB. Yes/No

3.

Temporary workers have the same right to safety information as other employees. Yes/No

4.

Age doesn't matter, risk affects every one equally. Yes/No

MSEE-004



1

P.T.O.

5.

You have to keep occupational health surveillance records for 40 years. Yes/No

6.

Health and safety failures cost our country up to Rs. 5000 crores each year. Yes/No

7.

Over a million workers get injured every year. Yes/No

8.

Pull, rather than push when moving equipment. Yes/No

9.

Most common cause of death of worker is fall from height. Yes/No

10.

Never stock combustible material near sources of Ignition. Yes/No

MSEE-004

2

SECTION - II Answer any 6 questions, carry 5 marks each. 11.

Define fire extinguishers and its types. 5

12.

Safety managers always rtalk that he is on the top 5 of the safety matters. But in court safety managers always been taken to task for failure to act professionally. Why ?

13.

Metal ladders are prohibited in some areas of 5 work. Why and where ?

14.

If smoking is prohibited in an area. How you will 5 detect that there is smoke ?

15.

What are the correct technique to lift an article ? 5

16.

What types of Extinguisher will be used after fire 5 from fuel, electric and Gas ?

17.

What is ladder. Why short ladders should not be 5 spliced together ?

18.

Temporary employees have the same right as 5 permanent employees. Do you agree - If not give reasons.

MSEE-004



3

P.T.O.

SECTION - III Answer any 2 questions. Each carry 25 marks. 19.

State different methods of identification of Risk. 25 Also highlight the infrastructure risk on over all risk analysis.

20.

Define the Hot work permit system. Under what 25 conditions the permit be approved in hazardous zone.

21.

Explain why ordinary switches are not suitable 25 for extra Hazardous zones. What suitable electrical switch / equipment is recommended.

22.

Write short notes on : (a)

Respirators

(b)

Breathing Apparatus

(c)

Safety Belts

(d)

Chemical Suits

MSEE-004

4

25

Manufacturing Process Industries.pdf

records for 40 years. Yes/No. 6. ... 10. Never stock combustible material near sources of. Ignition. Yes/No ... Displaying Manufacturing Process Industries.pdf.

81KB Sizes 0 Downloads 152 Views

Recommend Documents

potato chips manufacturing process pdf
There was a problem previewing this document. Retrying... Download. Connect more apps... Try one of the apps below to open or edit this item. potato chips manufacturing process pdf. potato chips manufacturing process pdf. Open. Extract. Open with. Si

06 me 45 manufacturing process - ii
b) Write a note on dressing and truing of grinding wheel. (06) c) Explain the factors to be considered while selecting a grinding wheel. (8). 7 a) What are the ...

soap and detergent manufacturing process pdf
Page 1 of 1. File: Soap and detergent manufacturing. process pdf. Download now. Click here if your download doesn't start automatically. Page 1 of 1. soap and ...

Process-Mapping-Process-Improvement-And-Process-Management ...
There was a problem loading more pages. Retrying... Whoops! There was a problem previewing this document. Retrying... Download. Connect more apps.

Read [PDF] Plastic Injection Molding Manufacturing Process Fundamentals (Fundamentals of Injection Molding) Read online
Plastic Injection Molding Manufacturing Process Fundamentals (Fundamentals of Injection Molding) Download at => https://pdfkulonline13e1.blogspot.com/0872634728 Plastic Injection Molding Manufacturing Process Fundamentals (Fundamentals of Injecti