IV B.Tech I Semester Supplementary Examinations, April/May 2005 MICROPROCESSORS AND INTERFACING ( Common to Electronics & Instrumentation Engineering,Bio-Medical Engineering and Mechatronics) Time: 3 hours Max Marks: 70 Answer any FIVE Questions All Questions carry equal marks ????? 1. (a) Differentiate microprocessor and microcomputer. (b) With a neat pin diagram of 8085 explain the functions of various pins. 2. (a) With suitable examples and diagrams discuss about various addressing modes of 8086. (b) Explain the following with reference to8086 (a) W-bit (b) D-bit (c) V-bit (d) Z-bit. 3. (a) Write an assembly language program sequence that will reverse the contents of the bytes PLACE through PLACE+N-1where N is the contents of NUM. (b) Briefly explain the shift instructions also give the examples. 4. Write a procedure SOLUTION that will use the arithmetic operators procedures to evaluate the expression ((A-B)*C) / D. 5. (a) List out different instructions involved with string operations. (b) Write an assembly language program segment to compare two strings stored at two different locations LOC1 and LOC2. 6. During block input byte transfer what changes occur as the datum is sent from the interface to the memory. Explain with a neat diagram. 7. Design an output port with the address FFH to interface the 1408 D/A. converter that is calibrated for a 0 to 10V range. Also draw the diagram. 8. Write short notes on: (a) USART (b) 8255. ?????
OR411051 IV B.Tech I Semester Supplementary Examinations, April ...
(b) Briefly explain the shift instructions also give the examples. 4. Write a procedure SOLUTION that will use the arithmetic operators procedures to evaluate the ...
(a) What is Redundancy? Explain the different types of Redundancy operation with LCU. (b) explain the operation of: i. Operator interface. ii. Engineer interface.
let us make a rough estimate of its role. For this assume isothermal operations in a 2.5-cm ID tubular reactor, using a Reynolds number of 10 000 for flowing fluid. The cracking reaction is approximately first order. If calculations show that 99% dec
With an example explain the distributed transparency for read-only application. 2. ... Discuss the catalog management in distributed databases. 6. What is the ...
(b) Sketch the bevel protractor and explain the various elements of it. 3. (a) Explain the following terms with respect to surface measurements. i. Lay ii. CLA iii.
(a) List and explain the metrics for the analysis model. (b) Describe the metrics for ... (a) Describe the object oriented design landscape. (b) What are design ...
What is a hot blast cupola? With a neat sketch describe the construction and operation of hot blast cupola. Explain the reactions those take place in the above.
iv. Minimum sampling rate v. aperture time required for the AD converter vi. Dynamic range of conversion in dB. 8. (a) Explain in detail abut analog multiplexing.
What are the modes of operation of a Hopfield network? Explain the algorithm for storage of information in a Hopfield network. Similarly explain the recall algo-.
alternator affects the performance of the differential protection of the three phase · stator. b) Describe how protection is provided in large turbo alternators against ...
(b) Can a second end check point record be encountered during analysis phase? (c) Why is the use of CLRS important for the use of UNDO actions that are not.
(a) Explain tree testing of prosthetic heart valve using a pulse duplicator. (b) Discuss the ... Explain with diagram, the types of exchangers used in artificial kidney.
(b) What is pretreatment required for sea water to be treated by electro dialysis? (c) Explain the conventional methods that could be employed for the treatment.
7.a) Explain the working principle of a simple accelerometer and vibrometer. b) Define the term gauge factor of strain gauge and strain gauge Rosetle. How are.
Find the loss of stress due to creep of concrete. (b) A concrete beam is prestressed by a cable carrying an initial prestressing force of 335kN. The cross sectional ...
NR. IV B.Tech I Semester Supplementary Examinations, November 2005 ... NR size is smaller than the fiber core, and the small gap between the source and.
RELIABILITY & SAFETY ENGINEERING · (Electronics & Control Engineering) ... (a) Explain the following terms in connection with reliability evaluation. [2+3].
NR. IV B.Tech I Semester Supplementary Examinations, November 2005 ... 3. Analyse the following frame using stiffness method. EI constant. (figure 3) [16].
What do you understand by Non-destructive testing techniques? List various tech- · nique of NDT and explain any three of them · [16]. 8. Write short notes on the ...
