PUMP REPLACEMENT INSTRUCTIONS: MP, WT and X3 JLT Pumps Configurations and Installation RE:

P/N 12158 KIT,MP/WT/X3, JLT PUMP 120V

Date: August 25, 2011

Engineer: Vincent Lau

Introduction: JLT pump P/N 50278 comes with built in diode and elbows. It also has two connection wires with Panduit terminals. Female Panduit terminal is 5" in length and male Panduit terminal is 10" long. The following tools will be needed for the replacement of your pump assembly • • • • •

Screw Driver, Philips #2 Side Cutters or Pincers Pliers End Cutters Rubber mallet

Remove Diode 0

Removal of old pump (Gotec pump that uses the external diode assy)

1) Ensure machine's power plug is disconnected from the wall outlet. Warning: Failure to disconnect power could result in an electrical shock hazard 2) Remove the white recovery bucket , 3) Remove the filter basket by removing the two screws holding it in place. Note.~ The WT-C2 machines will have two suction hoses. 4) Pull several inches of suction line up into the area behind the quick coupler to reduce the tension in the suction hose. Note: This provides added slack to the bottom pan so it can easily be lowered. 5) Place the machine on its side. 6) With a pair of side cutter or pincers, pry the hub cab off one of the wheels. Remove the Wheel 7) Lay the machine on its back (handle side down).

Page 1 of 3

P/N 12944 Rev. Date: 4/29/13

8) Remove all six (or eight) screws holding the bottom pan in place. Note: Some machines incorporate flat washers with the screws. Remove washers as well and keep the washers with their screws, if that is the case. 9) Re-insert one screw to hold the Nozzle in place while the bottom pan is loose. (Where applicable) 10) Stand the machine up and remove the three (or five) vent panel screws. Caution: Plastic vent panels will crack if too much stress is put on them. 11) Lay the machine on its back, supporting it at the main support with a 2" x 4" block or other item approximately the same size. 12) Remove the remaining wheel and axle assembly. 13) Lower the bottom pan 14) Note the flow direction ofthe pump being replaced. 15) Cut clamps off of the pump hoses by using Side Cutters or Pinchers cutting through and twisting the ear off. 16) Remove the hoses from the pump elbows. 17) Disconnect the pump wires and the diode assembly ( 6" red wire) from the power leads. Note: Cable tie (not provided with kit) may need to be cut from the wire bundle. 18) Remove the pump with the elbows still attached from the rubber mounts.

Installation of the new pump on the bottom pan for MP 1) 2) 3) 4) 5) 6)

Place new pump assembly pointed in the proper flow direction in the rubber mounts. Arrow (flow direction) is located on the label, which is on the metal frame of the pump. Slide clamps over both suction and pressure side of hoses and install hoses over elbow hose barbs as far as th~y will go. INSTALLATION Position each clamp so that it is 1/8" from the end of the hoses, and tighten clamps using side cutters or pincers, as shown. Connect both pump wires (DO NOT INSTALL DIODE) to the pump power wires. Install the included fuse, p/n 51135, where the diode was on previous configuration. Ensure that the wiring is positioned neatly away from the brush motor cam and brush holder assembly

Installation of the new pump on the bottom pan for WT Place new first pump (front) assembly pointed in the proper flow direction in the rubber mounts. Arrow (flow direction) is located on the label, which is on the metal frame of the pump. 2) Slide clamps over both suction and pressure side of hoses and install hoses over elbow hose barbs as far as they will go. 3) Position each clamp so that it is 1/8" from the end of the hoses, and tighten clamps using side cutters or pincers, as shown. 4) Place new second pump (rear), assembly pointed in the proper flow direction in the rubber mounts. Tighten clamps as with the first pump. Note: The second pump flow direction is the opposite of the first pump. 5) Connect both pump wires (DO NOT INSTALL DIODES) to the pump power wires. 6) Install the included fuses, p/n 51135, where the diodes were on previous configuration. 7) Ensure that the wiring is positioned neatly away from the brush motor cam and brush holder assembly. 1)

Installation of the bottom pan to the lower tank 1) Remove the screw from the nozzle and hold the nozzle in place. (Where applicable) 2) Raise the bottom pan and install two screws into the front lip of the hottom pan and through the nozzle. 3) Slide the axle assembly through the holes in the lower tank. 4) Turn the unit on its side and install the wheel over the axle. 5) Using a rubber mallet firmly strike the new hubcap onto the end of the axle. 6) Install the remaining four (or six) screws into the bottom pan securing it to the lower tank. Tighten the screws evenly. Caution: Do not over tighten. Over tightening may result in the bottom pan cracking · 7) Place the machine upright. 8) Reinstall three (or five) screws securing the top of the vent panel. 9) Push the slack of the solution line back into the lower tank.

Page 2 of 3

P/N 12944 Rev. Date: 4/29/13

Test the machine for proper performance 1) 2) 3) 4) 5) 6)

Ensure the power switch is in the off position. Plug the machine into a live outlet. Ensure the machine circuit breaker is depressed or set to the ON position. If you have a two switch configured machine ensure that the switch is in the carpet position., Turn the machine ON (carpet position for one-switch configured machines). Press the red trigger switch and ensure that the pump operates. Note: If the machine is without solution the pump will chatter. Turn the machine ON to the upholstery position to ensure that the pump operates in that setting as well.

Page 3 of 3

P/N 12944 Rev. Date: 4/29/13

Rug Doctor Pump Kit Instructions (Current).pdf

MP, WT and X3 JLT Pumps Configurations and Installation. RE: P/N 12158 KIT,MP/WT/X3, JLT PUMP 120V. Date: August 25, 2011 Engineer: Vincent Lau. Introduction: JLT pump P /N 50278 comes with built in diode and elbows. It also has two connection wires with Panduit. terminals. Female Panduit terminal is 5" in length ...

86KB Sizes 3 Downloads 170 Views

Recommend Documents

Mendel90 Kit Instructions - GitHub
Jul 27, 2012 - 01/10/13 Updated remaining assembly views for black screws and red ...... Start by printing a paper template from the pdf drawing y_heatshield.pdf. ...... thick then you might want to re-slice the Android STL with the PLA 0.2mm.

Mendel90 Kit Instructions -
Red / blue are one pair and green / black the other pair. ..... It is vital that the power connections to the Melzi make a good low resistance contact. If not the joint ...

Financial Emergency Kit Instructions - Community Financial Services ...
any CFSB location or call 527-8616 or toll free 1-888-226-5669. We are here to .... Mail a copy of your FEK and legal documents to your attorney in an envelope to be opened with ... List the names of individuals living in the residence: .... These he

Financial Emergency Kit Instructions - Community Financial Services ...
any CFSB location or call 527-8616 or toll free 1-888-226-5669. ..... The Poison Control Center. If you have a poisoning emergency, call 1-800-222-1222.

Oriental Rug Designs.pdf
Whoops! There was a problem loading more pages. Retrying... Whoops! There was a problem previewing this document. Retrying... Download. Connect more apps... Try one of the apps below to open or edit this item. Oriental Rug Designs.pdf. Oriental Rug D

whirlpool duet stacking kit instructions pdf
whirlpool duet stacking kit instructions pdf. whirlpool duet stacking kit instructions pdf. Open. Extract. Open with. Sign In. Main menu.

PUMP, PUMP AND AWAY -
Come with some innovative design of model rocket which use water as its reaction mass. (called water rocket) and defy the laws of gravity to keep your rocket in ...

Pump construction
References Cited by the Examiner. The following references, cited by the Examiner, are of record in the patented ñle of this patent or the original patent. 10. 15. 8.

RUG IN ONE PIECE.pdf
Page 1 of 1. RUG IN ONE PIECE. Beginning Square. Cast on 49 stitches (or any uneven number). 1st Row: Knit. Slipping the last stitch. (This is done with every row.) 2nd Row: Knit 23 sts, K3 together, Knit 23 sts. 3rd Row: & every alternate row, Knit.

Pump Submersible.pdf
Do not walk on wet area until all power has been. turned off. If the shut-off box is in the basement, call. the electric company or hydro authority to shutoff. the service to house, or call your local fire depart- ment for instructions. Failure to fo

CENTRIFUGAL PUMP HANDBOOK
A coupling is used whenever it is necessary to connect two shafts and to transfer torque from one shaft (drive) to another shaft (pump), The drive can be an electric motor, diesel engine, or steam or gas turbine. The method of operation is decisive f

CENTRIFUGAL PUMP HANDBOOK
QR =Q.(D2RID,r. HR =H.(D2R ID2 r m z 2-3. - exponent near 3: for small corrections of diameter and additional sharpening of impeller blade oullet on pressure side. ~ exponent near 2: for corrections of diameter larger than 5%. When for example season

Doctor Doctor RCDE64.pdf
Retrying... Download. Connect more apps... Try one of the apps below to open or edit this item. Doctor Doctor RCDE64.pdf. Doctor Doctor RCDE64.pdf. Open.

pump that young.pdf
Anal dp dvd pump that young. ass 2 evil playgrounds porn. Pump that young ass 2, scene 5 asexbox.eu. My favorite asian hd page. 8 free porn adu videos forum ...

INSTRUCTIONS FOR EXAM ADMINISTRATORS INSTRUCTIONS 1 ...
For Online Examination, we have divided Candidates into three batches as per the maximum sitting capacity available for conducting ... The online test is divided into 3 sections equally distributed in 1 hour – each section is timed for 20 minutes.

Heat Pump GSM Remote Control
Control your heat pump from anywhere. Easy to use. Access Code -protection to prevent unauthorized remote access. Easy access to most frequently used controls. A total of 12 remote controlled heat pump related functions/parameters. Preserves settings

Exercise instructions
Jul 30, 2016 - Send me an email at the latest on August 13th, 2016 with your attached CPN file and CC yourself and your partner too so that I know who is in ...

INSTRUCTIONS FOR EXAM ADMINISTRATORS INSTRUCTIONS 1 ...
INSTRUCTIONS. 1. For Online Examination, we have divided Candidates into three batches as per the maximum ... The online test is divided into 3 sections equally distributed in 1 hour – each section is timed for 20 minutes. 4. .... of the test candi

centrifugal pump performance curves pdf
curves pdf. Download now. Click here if your download doesn't start automatically. Page 1 of 1. centrifugal pump performance curves pdf. centrifugal pump ...