FlexCut Sticky Maxx – Application Instruction s Heat Transfer Flex Film for Plotter Cutting FlexCut Sticky Maxx is a water based 100% polyurethane super thin & super soft film with excellent stretch, opacity & color fastness. The sticky liner / carrier allows for fine cutting detail and fast weeding of a graphic or lettering. Cutting is easy with both a drag-knife and the tangential cutting technology. Large and multi-layered graphics can be applied without loss of wearing comfort. Cut Mirrored
FlexCut Sticky Maxx is suitable for cotton, cotton – polyester and blended textiles. It is not suitable for nylon or coated textiles. Heat Pressing: Apply the graphic to the textile and press for 15-17 seconds at 330°F / 165°C with medium to high pressure. Then remove the carrier / transfer film using a hot or warm peel. Washing resistance up to 140°F / 60°C.
Cut in Mirror Image, Wrong Reading Cutting Conditions: Blade: Relief angle 30° / 45° Blade pressure, med., 60 to 90 grams of down force. Test cuts recommended Cutting Speed: ≈40 cm/s Transfer Recommedations:
Temperature: 330°F / 165°C Time: 15-17 sec. Pressure: medium / high Hot / warm or cold peel of the transfer / carrier film
Layering Possible, Flex on Flex Suitable Textiles: Cotton, cotton – polyester & blended textiles. Not suitable for nylon or coated textiles Wash Resistance: 140°F 60°C wash resistance
Transfer Design
Colors: FlexCut Sticky - 33 colors & 4 neon colors
Layering is possible: Flex on Flex. We do not recommend more than four layers.
Available in:
Layering recommendations:
15” x 5, 10, 25,& 50yd. rolls 19.7 x 10 & 25yd. rolls
Five (5) seconds per layer with the final layer at fifteen (15) seconds or at the recommended time for the last layer applied. See SEF’s application instruction sheet for time & temperature settings specific to the last layer applied.
Custom roll widths & lengths may be available.
Hot or Warm Peel
Garment Care: wash & dry garment inside out, machine wash & dry at low temperatures, see specification, “Wash Resistance” use mild detergents, No Chlorine, Do not dry clean Flex; Flock OK, wait 24 hours before first washing.
Store SEF Heat Transfer Materials in a cool and dry place; protect against the influence of light when stored. We recommend not to exceed a storage period of 24 months. Due to the variety of possible influences / exposure outside of our control, to include processing / use, all specifications should be viewed as reference values. We recommend a suitability test to the material before a production. Technical specifications rest on extensive tests and technical research, however, a legally binding warranty of specific characteristics and or performance cannot be provided.
01-FlexCut Sticky Maxx App. Instr. v6, 081515
FlexCut Sweet – Application Instructions Heat Transfer Flex Film for Cutting Plotters Cut Mirrored
FlexCut Sweet is a water based 100% polyurethane film on a NON-STICKY polyester liner. FlexCut Sweet has an especially soft feel with excellent elasticity and color fastness. Large and multi-layered designs can be applied without the loss of wearing comfort. An excellent solution for sports related applications, as it weeds easily and it is economically priced. FlexCut Sweet is super soft and super sweet!
FlexCut Sweet is suitable for cotton, cotton polyester, blended textiles and some light colored polyesters. It is not suitable for nylon or Weed Design coated textiles. Transfer Design
Heat Pressing: Apply the graphic to the textile and press for 15-17 seconds at 330°F / 165°C with medium to high pressure. Then remove the carrier / transfer film using a warm peel. Washing resistance up to 140°F / 60°C.
Cutting Conditions: Blade: Relief angle 30° or 45° Blade pressure, med., 60 to 90 grams of down force. Test cuts recommended Cutting Speed: ≈40 cm/s Suitable Textiles: Cotton, cotton – polyester & blended textiles. Not suitable for nylon or coated textiles Layering Possible, Flex on Flex Transfer Conditions:
Temperature: 330°F / 165°C Time: 15-17 sec. Pressure: medium / high Warm peel of the transfer / carrier film
Wash Resistance: 140°F / 60°C wash resistance Colors: FlexCut Sweet is available in 18 colors Available in:
Warm Peel
Layering is possible: Flex on Flex. We do not recommend more than four layers.
Cut in Mirror Image, Wrong Reading
15” x 5 yds. 19.7 x 10, 25 & 50 yds. Custom roll widths & lengths may be available
Layering recommendations: Five (5) seconds per layer with the final layer at fifteen (15) seconds or at the recommended time for the last layer applied. See SEF’s application instruction sheet for time & temperature settings specific to the last layer applied.
Garment Care: wash & dry garment inside out, machine wash & dry at low temperatures, see specification, “Wash Resistance” use mild detergents, No Chlorine, Do not dry clean Flex; Flock OK, wait 24 hours before first washing.
Store SEF Heat Transfer Materials in a cool and dry place; protect against the influence of light when stored. We recommend not to exceed a storage period of 24 months. Due to the variety of possible influences / exposure outside of our control, to include processing / use, all specifications should be viewed as reference values. We recommend a suitability test to the material before a production. Technical specifications rest on extensive tests and technical research, however, a legally binding warranty of specific characteristics and or performance cannot be provided.
02-FlexCut Sweet App. Instr. v6 081515
FlexCut Sticky Nylon – Application Instructions Flex Film for Nylon & Coated Textiles Transfer films often have adhesion problems to textiles made of nylon, nylon blends and or coated textiles. These problems do not arise because of the nylon material itself, but instead because nylon is often coated with different substances in order to make Cut Mirrored it water resistant. These coatings not only resist water, but also the hot melt adhesive used in standard heat transfer films. However the multilayer design of FlexCut Sticky Nylon contains a hot melt adhesive that was developed especially for adhering to water resistant textiles.
Cut in Mirror Image, Wrong Reading Cutting Conditions: Blade: Relief angle 30° or 45° Blade pressure, med., 60 to 90 grams of down force. Test cuts recommended Cutting Speed: ≈40 cm/s Suitable Textiles: Nylon and other coated textiles Layering Possible, Flex on Flex
FlexCut Sticky Nylon is suitable for nylon and other coated textiles. Testing is always recommended before starting production to ensure compatibility. Transfer Design
Heat Pressing: Apply the graphic to the textile and press for 15-17 seconds at 240°F / 115°C with medium to high pressure. Then remove the carrier / transfer film using a hot or warm peel. Washing resistance up to 104°F / 40°C. Layering is possible: Flex on Flex. We do not recommend Hot or Warm Peel more than four layers.
Layering recommendations: Five (5) seconds per layer with the final layer at fifteen (15) seconds or at the recommended time for the last layer applied. See SEF’s application instruction sheet for time & temperature settings specific to the last layer applied.
Transfer Conditions:
Temperature: 240°F / 115°C Time: 15-17 sec. Pressure: medium / high Hot or Warm peel of the carrier / transfer film
Wash Resistance: 104°F / 40°C wash resistance Colors: FlexCut Nylon is available in 8 colors, including gold & silver metallic
Available in: 15” x 5, 10, 25 & 50 yds. Custom roll widths & lengths may be available.
Garment Care: wash & dry garment inside out, machine wash & dry at low temperatures, see specification, “Wash Resistance” use mild detergents, No Chlorine, Do not dry clean Flex; Flock OK, wait 24 hours before first washing.
Store SEF Heat Transfer Materials in a cool and dry place; protect against the influence of light when stored. We recommend not to exceed a storage period of 24 months. Due to the variety of possible influences / exposure outside of our control, to include processing / use, all specifications should be viewed as reference values. We recommend a suitability test to the material before a production. Technical specifications rest on extensive tests and technical research, however, a legally binding warranty of specific characteristics and or performance cannot be provided.
03-FlexCut Sticky Nylon App. Instr. v6 081515
FlexCut Sticky Nylon – Application Instructions
Garment Care: wash & dry garment inside out, machine wash & dry at low temperatures, see specification, “Wash Resistance” use mild detergents, No Chlorine, Do not dry clean Flex; Flock OK, wait 24 hours before first washing.
Store SEF Heat Transfer Materials in a cool and dry place; protect against the influence of light when stored. We recommend not to exceed a storage period of 24 months. Due to the variety of possible influences / exposure outside of our control, to include processing / use, all specifications should be viewed as reference values. We recommend a suitability test to the material before a production. Technical specifications rest on extensive tests and technical research, however, a legally binding warranty of specific characteristics and or performance cannot be provided.
03-FlexCut Sticky Nylon App. Instr. v6 081515
MetalFlex – Application Instructions Shiny, Metal Effect, Flex Heat Transfer Film for Cutting Plotters
Cut Mirrored
MetalFlex is a high quality, multi-layered polyurethane film on a polyester liner. It has a very high shiny metal-effect look. MetalFlex is very thin and highly elastic allowing for stretch with the textile. Above all, MetalFlex distinguishes itself from the rest with its excellent weeding characteristics. MetalFlex is available in 7 colors, additional colors upon request. Weed Design
MetalFlex is suitable for cotton, cotton – polyester and blended textiles. It is not suitable for nylon or coated textiles. It is wash resistant up to 104°F. At the same time, it is important to ensure that only mild detergents without bleach or oxidizing agents are used. Otherwise the metal surface will be affected and lose its sheen. Transfer Design
Heat Pressing: Apply the graphic to the textile and press for 15-17 seconds at Remove Liner 330°F / 165°C with medium to high pressure. Then remove the carrier / transfer film using a cold peel. Washing resistance up to 104°F / 40°C
Layering is possible: MetalFlex on Flex. We do not recommend more than four layers.
Cut in Mirror Image, Wrong Reading Cutting Conditions:
Blade: Relief angle 30° / 45° Blade pressure, med., 60 to 90 grams of down force. Test cuts recommended Cutting Speed: ≈40 cm/s
Transfer Recommedations:
Temperature: 330°F / 165°C Time: 15-17 sec. Pressure: medium / high Cold peel for highest level of shine
Layering Possible, MetalFlex on Flex Suitable Textiles:
Cotton, cotton – polyester & blended textiles. Not suitable for nylon or coated textiles
Wash Resistance:
104°F 40°C wash resistance
Colors:
MetalFlex is available in - 7 colors
Silver
Gold
Orange Copper
Red
Blue
Green
Gun Metal
Available in:
15” x 5, 10, 25 rolls
Custom roll widths & lengths may be available.
Layering recommendations: Five (5) seconds per layer with the final layer at fifteen (15) seconds or at the recommended time for the last layer applied. See SEF’s application instruction sheet for time & temperature settings specific to the last layer applied. Garment Care: wash & dry garment inside out, machine wash & dry at low temperatures, see specification, “Wash Resistance” use mild detergents, No Chlorine, Do not dry clean Flex; Flock OK, wait 24 hours before first washing.
Store SEF Heat Transfer Materials in a cool and dry place; protect against the influence of light when stored. We recommend not to exceed a storage period of 24 months. Due to the variety of possible influences / exposure outside of our control, to include processing / use, all specifications should be viewed as reference values. We recommend a suitability test to the material before a production. Technical specifications rest on extensive tests and technical research, however, a legally binding warranty of specific characteristics and or performance cannot be provided.
04-Metalflex App. Instr. v6 081515
FlexCut Sticky SBB – Application Instructions Flex Film for Textile with Heavy Dye Migration Cut Mirrored
Commercial polyester textiles / fabrics are most commonly white and then dyed with a dispersion of sublimation dyes to change the color using heat beginning at 266°F / 130°C. This process allows the dyes to dissolve and bond to the polyester fibers. Depending on the process used, or the quality of the dye, colorants will reactivate, “becoming active”, when exposed to high heat again, i.e. when heat pressing a graphic transfer.
FlexCut Sticky SBB was formulated with a proprietary Sublimation Blocking Barrier to prevent sublimated dyed inks from migrating through to the first surface, preventing staining, of our heat transfer material after transferring.
Weed Design
FlexCut Sticky SBB is a "normal" flex film with very good opacity & covering power, with good elasticity and a soft feel. In addition, it has very good weeding characteristics thanks to its sticky polyester liners.
Cut in Mirror Image, Wrong Reading Cutting Conditions: Blade: Relief angle 30° or 45° Blade pressure, med., 60 to 90 grams of down force. Test cuts recommended Cutting Speed: ≈40 cm/s Suitable Textiles: Polyester & blended textiles. Not suitable for nylon or coated textiles Layering Possible, flex & flock on SBB Transfer Conditions:
Temperature: 295°F / 145°C Time: 18-20 sec. Pressure: medium / high Hot / warm peel of the transfer / carrier film
Layering Possible, Flex on Flex Wash Resistance: 140°F / 60°C wash resistant Colors:
Transfer Design
Heat Pressing: Apply the graphic to the textile and press for 18-20 seconds at Remove Liner 295°F / 145°C with medium to high pressure. Then remove the carrier / transfer film using a hot or warm peel. Washing resistance up to 140°F / 60°C.
FlexCut Sticky SBB is available in 01 white and 05 lemon yellow Available in: 15” x 5, 10, 25 yds. Call for additional roll widths and lengths
FlexCut Sticky SBB is suitable for polyester and blended textiles. It is not suitable for nylon or coated textiles.
Garment Care: wash & dry garment inside out, machine wash & dry at low temperatures, see specification, “Wash Resistance” use mild detergents, No Chlorine, Do not dry clean Flex; Flock OK, wait 24 hours before first washing.
Store SEF Heat Transfer Materials in a cool and dry place; protect against the influence of light when stored. We recommend not to exceed a storage period of 24 months. Due to the variety of possible influences / exposure outside of our control, to include processing / use, all specifications should be viewed as reference values. We recommend a suitability test to the material before a production. Technical specifications rest on extensive tests and technical research, however, a legally binding warranty of specific characteristics and or performance cannot be provided.
05-FlexCut Sticky SBB App. Instr. v6 081515
ReflexCut Sweet – Application Instructions Heat Transfer Reflective Flex Film for Cutting Plotters Remove the Protective Film
ReflexCut Sweet is a safety grade reflective polyurethane constructed film with micro glass beads on a non-sticky polyester liner / carrier. ReflexCut Sweet is very opaque while still allowing for high elasticity. Great for light or dark colored textile application. ReflexCut Sweet can be cut using a drag-knife or tangential cutting technology. ReflexCut Sweet is suitable for cotton, polyester and blended textiles. It is not suitable for nylon or coated textiles. It is wash resistant up to 140°F / 60°C.
Before Cutting, remove the protective film.
Cut in Mirror Image, Wrong Reading Cutting Conditions: Blade: Relief angle 45° or 60° Blade pressure, med., 80 to 110 grams of down force. Test cuts recommended Cutting Speed: ≈20 cm/s Special Instructions: Before cutting, remove the protective film Suitable Textiles: Cotton, polyester & blended textiles. Not suitable for nylon or coated textiles Transfer Conditions:
Heat Transferring: The plotted and weeded lettering or designs are heat pressed onto the textiles for 4 seconds at 340°F / 170°C. Remove the carrier / transfer film immediately using a hot peel and repress for 8 – 10 seconds at 340°F / 170°C. Transfer Design, Step 1.
Remove Liner and Re-Press, step 2
Done!
Step 1. Heat Transferring:
Temperature: 340°F / 170°C Time: 4 sec. Pressure: medium Hot peel of the carrier
Step 2. Heat Transferring: Heat Press Temp. 340°F / 170°C Time: 8-10 sec. Pressure: medium Wash Resistance: 140°F / 60°C wash resistance Colors: Non-reflecting, color is silver Reflecting, white in color Available in: 15” x 5 & 10 yds.
Reflex Cut Sweet is a safety grade high quality reflective grade heat transfer film certified in accordance with EN-471:2003-Class 2.
Custom roll widths & lengths may be available.
Certificate available upon request. Garment Care: wash & dry garment inside out, machine wash & dry at low temperatures, see specification, “Wash Resistance” use mild detergents, No Chlorine, Do not dry clean Flex; Flock OK, wait 24 hours before first washing.
Store SEF Heat Transfer Materials in a cool and dry place; protect against the influence of light when stored. We recommend not to exceed a storage period of 24 months. Due to the variety of possible influences / exposure outside of our control, to include processing / use, all specifications should be viewed as reference values. We recommend a suitability test to the material before a production. Technical specifications rest on extensive tests and technical research, however, a legally binding warranty of specific characteristics and or performance cannot be provided.
06-ReflexCut Sweet App. Instr. v6 081515
VelCut Flock – Application Instructions Heat Transfer Flock Material for Cutting Plotters Mirrored Cut
VelCut Flock is a high quality flock film specially formulated to maintain its soft-to-the-touch feel and its color fastness over extended washing cycles. VelCut provides by way of plotter cutting a dimensional / embroidered look at a much lower cost than embroidery. VelCut has a very high opacity while not giving up elasticity, as it stretches very well with the textile. VelCut uses a specially formulated adhesive liner / carrier which when cut properly, allows for excellent weeding of fine detailed graphics and small lettering.
VelCut Flock is suitable for cotton, polyester, and Weed Design blended textiles. It is not suitable for nylon or coated textiles.
After weeding, apply graphic to the textile and press using low pressure. Press for 15 – 17 sec. at 330 °F / 165°C. Then remove the carrier / transfer film using a warm or cold peel. VelCut is wash resistant up to 140°F / 60°C. Layering is possible, Flock on Flex only!
Blade: Relief angle 45° or 60° Blade pressure, 80 to 110 grams of down force. Test cuts recommended Cutting Speed: ≈20-40 cm/s Special Instructions: See blade depth instructions on reverse side.
Suitable Textiles: Cotton, polyester, blended fabric. Not suitable for nylon and other coated textiles
Layering Possible, Flock on Flex Transfer Conditions:
Wash Resistance: 140°F / 60°C wash resistance Colors: Available in 20 standard colors 4 Neon colors Available in:
Remove Liner
Ten (7) seconds per layer for SEF Flex films at medium to high pressure, with the flock layer pressing last using VelCut’s application settings for the final pressing. We do not recommend more than 4 layers.
Cutting Conditions:
Temperature: 330°F / 165°C Time: 15-17 sec. Pressure: low to eliminate crushing of the flock fibers Peel warm or cold
Cutting & Heat Pressing: See reverse side of document for proper cutting blade depth. Cut in mirror image, wrong reading. Always do a test cut before proceeding with production.
Transfer Design
Cut in Mirror Image, Wrong Reading
19.7” x 5 & 10 yds. Custom roll widths & lengths may be available.
Garment Care: wash & dry garment inside out, machine wash & dry at low temperatures, see specification, “Wash Resistance” use mild detergents, No Chlorine, Do not dry clean Flex; Flock OK, wait 24 hours before first washing.
Store SEF Heat Transfer Materials in a cool and dry place; protect against the influence of light when stored. We recommend not to exceed a storage period of 24 months. Due to the variety of possible influences / exposure outside of our control, to include processing / use, all specifications should be viewed as reference values. We recommend a suitability test to the material before a production. Technical specifications rest on extensive tests and technical research, however, a legally binding warranty of specific characteristics and or performance cannot be provided.
07-VelCut Flock App. Instr. v6 081515
VelCut Flock – Application Instructions
Garment Care: wash & dry garment inside out, machine wash & dry at low temperatures, see specification, “Wash Resistance” use mild detergents, No Chlorine, Do not dry clean Flex; Flock OK, wait 24 hours before first washing.
Store SEF Heat Transfer Materials in a cool and dry place; protect against the influence of light when stored. We recommend not to exceed a storage period of 24 months. Due to the variety of possible influences / exposure outside of our control, to include processing / use, all specifications should be viewed as reference values. We recommend a suitability test to the material before a production. Technical specifications rest on extensive tests and technical research, however, a legally binding warranty of specific characteristics and or performance cannot be provided.
07-VelCut Flock App. Instr. v6 081515
Tatoo – Application Instructions Printable Flex Film for Eco-Solvent, Solvent, Latex & UV Inks Print and Cut
Tatoo is a high-quality, matte / semi-gloss, white multilayer polyurethane film on a polyester liner / carrier. Tatoo is a super thin super soft film with high opacity allowing for excellent stretch with the fabric. Tatoo does not require pre-heating, however, the media should be at 68°F to 80°F for optimum ink adhesion to the media. Tatoo is compatible with eco-solvent, solvent, latex & UV inks.
Suitable Inks: Eco-Solvent, Solvent & Latex Printer Profile Setting: Roland, TTRH or HTM2, Garment Heat Transfer White calendared matte or semi-gloss vinyl Printer mfg. settings for heat transfer material Suitable Textiles:
Apply FlexTape
Verify the printed design / ink is dry before applying our FlexTape transfer tape. Drying time is generally very quick but it can take up to 5 hours or more based on the type of ink, ink density and ambient conditions. After applying the FlexTape transfer tape to the graphic, allow 15/30 minutes before transferring the graphic to the textile. This will ensure good adhesion of the FlexTape to the printed image.
Cotton, cotton – polyester & blended textiles. Not suitable for Nylon or coated textiles Heat Settings, Pre & Post: Switched off or lowest settings Cutting Conditions: Blade: Relief angle 30° or 45° Blade pressure, med., 50 to 80 grams of down force. Test cuts recommended Cutting Speed: ≈40 cm/s
Heat Transfer, Option 1: With the image facing up, peel the transfer away from the liner / carrier. Apply the graphic to the textile and press for 17 seconds at 330°F / 165°C with medium to high pressure. Then Hot or Warm Peel remove the FlexTape using a hot or warm peel. Washing resistance up to 104°F / 40°C.
Transfer Tape:
Heat Transfer, Option 2: Alternate pressing method which can provide higher washing resistance, up to 140°F / 60°C.
Wash Resistance:
With the image facing up, peel transfer away from the liner / carrier. Apply graphic to the textile and press for 5 seconds at 330°F / 165°C, medium to high pressure. Remove the FlexTape using a hot or warm peel. Do a second pressing without the transfer tape for 15 seconds at 330°F / 165°C.
FlexTape / transfer tape required Transfer, Option 1:
Temperature: 330°F / 165°C Time: 17 sec. Pressure: medium / high Hot / warm peel of the transfer tape
Option 1 will provide a washing resistance 104°F / 40°C For higher washing resistance of 140°F / 60°C use transfer option 2 Available in: 19.7” x 5, 10, 25 & 50 yds. 29.5” x 5, 10, 25 & 50 yds. Call for additional roll widths and lengths, i.e. 54” & 59”
Garment Care: Wait 24 hours before first washing, wash & dry garment inside out, machine wash & dry at low temperatures, see specification, “Wash Resistance” use mild detergents, No Chlorine, do not dry clean Flex; Flock OK.
Store SEF Heat Transfer Materials in a cool and dry place; protect against the influence of light when stored. We recommend not to exceed a storage period of 24 months. Due to the variety of possible influences / exposure outside of our control, to include processing / use, all specifications should be viewed as reference values. We recommend a suitability test to the material before a production. Technical specifications rest on extensive tests and technical research, however, a legally binding warranty of specific characteristics and or performance cannot be provided.
08-Tatoo App. Instr. v6 081515
Tatoo – Application Instructions Tatoo Transfer Recommendations That Have Yielded Positive Results! Tatoo should be cut with a 30 or 45 degree "sharp" blade at approximately 50 to 80 grams of down force. If you are using more down force than 80 grams, change your blade out for a new one. We recommend that you always do a test cut before starting a production. A dull blade will make for more difficult weeding and transferring of a graphic. For Information on cutting tips, you can visit our company‘s Blog: (http://sefamericas.blogspot.com), for articles / bulletins, i.e. Plotter Cutting Heat Transfer Films Procedure for masking and peeling of graphics from the carrier as follows: 1. Wait at least 30 minutes for the printed graphic to dry before applying the transfer tape. Drying could take longer based on ink density, the ambient temperature and humidity in the shop. 2. Apply the transfer tape and allow 15/30 minuntes for the transfer tape to set up. Adhesives build over time. 3. Before peeling the graphic, re-squeegee the graphic firmly, then with the graphic laying on the table "image facing up" (see pictures), lift the transfer tape up and away from the liner / carrier. If the transfer tape picks the graphic up OK at 15/30 minutes dwell time, you can shorten the waiting period.
Garment Care: Wait 24 hours before first washing, wash & dry garment inside out, machine wash & dry at low temperatures, see specification, “Wash Resistance” use mild detergents, No Chlorine, do not dry clean Flex; Flock OK.
Store SEF Heat Transfer Materials in a cool and dry place; protect against the influence of light when stored. We recommend not to exceed a storage period of 24 months. Due to the variety of possible influences / exposure outside of our control, to include processing / use, all specifications should be viewed as reference values. We recommend a suitability test to the material before a production. Technical specifications rest on extensive tests and technical research, however, a legally binding warranty of specific characteristics and or performance cannot be provided.
08-Tatoo App. Instr. v6 081515
Tatoo Nylon – Application Instructions Printable Flex Film for Nylon & Coated Textiles Transfer films often have adhesion problems on textiles made of nylon, nylon blends and or coated textiles. These problems do not arise because of the nylon material itself, but instead because nylon is often coated with different substances in order to make it water resistant. These coatings not only resist water, but also the hot melt adhesive used in standard heat transfer films. However the multilayer design of Tatoo Nylon contains a hot melt adhesive that was developed especially for adhering to water-resistant textiles. Testing is always recommended before starting production to ensure compatibility.
Print and Cut
Suitable Inks: Solvent, Eco-Solvent, UV, Latex “color fastness may be limited” Printer Profile Setting: Roland, TTRH or HTM2, Garment Heat Transfer White calendared matte or semigloss vinyl Printer mfg. settings for heat transfer material Printer Heat Settings, Pre & Post: 110°F – 115°F Suitable Textiles:
Tatoo Nylon is compatible with eco-solvent, Apply FlexTape
Nylon and other coated textiles
solvent, UV & latex inks. To optimize the inks adhesion to the media, it is recommended that the pre and post heat printer settings be set at 110°F to 115°F. When printing with latex inks, we recommend testing prior to production.
Cutting Conditions:
Verify the printed design / ink is dry before applying our FlexTape transfer tape. Drying time is generally very quick, but it can take up to 5 hours or more based on the type of ink, ink density and ambient conditions. After applying FlexTape to the graphic, allow a minimum of 15 minutes before transferring the graphic to the textile. This will ensure good adhesion of the FlexTape to the printed image. Heat Pressing: With the image facing up, peel transfer away from the liner / carrier, apply the graphic to the textile and press for 15-17 seconds at 240°F / 115°C with medium to high pressure. Then remove the FlexTape using a hot or warm peel. Washing resistance up to 104°F / 40°C.
Blade: Relief angle 45° optimum Blade pressure, med., 60 to 80 grams of down force. Test cuts recommended Cutting Speed: ≈40 cm/s Transfer Tape: FlexTape / transfer tape required Transfer Conditions:
Temperature: 240 °F / 115°C Time: 17 sec. Pressure: medium / high Hot or warm peel
Wash Resistance: 104°F / 40°C wash resistant Available in: 19.7” x 5, 10, 25 & 50 yds. 29.5” x 5, 10, 25 & 50 yds. Call for additional roll widths and lengths, i.e. 54” & 59”
Hot or Warm Peel Garment Care: wash & dry garment inside out, machine wash & dry at low temperatures, see specification, “Wash Resistance” use mild detergents, No Chlorine, Do not dry clean Flex; Flock OK, wait 24 hours before first washing.
Store SEF Heat Transfer Materials in a cool and dry place; protect against the influence of light when stored. We recommend not to exceed a storage period of 24 months. Due to the variety of possible influences / exposure outside of our control, to include processing / use, all specifications should be viewed as reference values. We recommend a suitability test to the material before a production. Technical specifications rest on extensive tests and technical research, however, a legally binding warranty of specific characteristics and or performance cannot be provided.
09-Tatoo Nylon App. Instr. v6 081515
Tatoo Nylon – Application Instructions
Garment Care: wash & dry garment inside out, machine wash & dry at low temperatures, see specification, “Wash Resistance” use mild detergents, No Chlorine, Do not dry clean Flex; Flock OK, wait 24 hours before first washing.
Store SEF Heat Transfer Materials in a cool and dry place; protect against the influence of light when stored. We recommend not to exceed a storage period of 24 months. Due to the variety of possible influences / exposure outside of our control, to include processing / use, all specifications should be viewed as reference values. We recommend a suitability test to the material before a production. Technical specifications rest on extensive tests and technical research, however, a legally binding warranty of specific characteristics and or performance cannot be provided.
09-Tatoo Nylon App. Instr. v6 081515
Tatoo SBB – Application Instructions Printable Flex Film for Textile with Heavy Dye Migration Print and Cut
Commercial polyester textiles / fabrics are most commonly white and then dyed with a dispersion of sublimation dyes to change the color using heat beginning at 266°F / 130°C. This process allows the dyes to dissolve and bond to the polyester fibers. Depending on the process used, or the quality of the dye, colorants will reactivate, “becoming active”, when exposed to high heat again, i.e. when heat pressing a graphic transfer.
Tatoo SBB was formulated with a proprietary Sublimation Blocking Barrier to prevent sublimated dyed inks from migrating through to the first surface, preventing staining, of our heat transfer material after transferring. Tatoo SBB accepts eco-solvent, solvent and latex inks. When printing with latex inks, we recommend testing prior to production. Prior to printing, the media should be at 68°F to 80°F for optimum ink adhesion to the media.
Suitable Inks: Eco-Solvent, Solvent, Latex “color fastness may be limited” Printer Profile Setting: Roland, TTRH, Garment Heat Transfer White calendared matte or semi-gloss vinyl Printer mfg. settings for heat transfer material Printer Heat Settings, Pre & Post: Switched off or lowest settings Suitable Textiles:
Polyester & blended textiles. Not suitable for nylon or coated textiles
Layering Possible, flex & flock on SBB Cutting Conditions:
Verify the printed design / ink is dry before Apply FlexTape applying our FlexTape transfer tape. Drying time is generally very quick, but it can take up to 5 hours or more based on the type of ink, ink density and ambient conditions. After applying the FlexTape to the graphic, allow a minimum of 15 minutes before transferring the graphic to the textile. This will ensure good adhesion of the FlexTape to the printed graphic. Heat Pressing: With the image facing up, peel
the transfer away from the liner / carrier. Apply the graphic to the textile and press for 18 – 20 seconds at 295°F / 145°C with medium to high pressure. Then remove the FlexTape using a hot or warm peel. Washing resistance up to 140°F / 60°C.
Blade: Relief angle 30° or 45° Blade pressure, med., 60 to 90 grams of down force. Test cuts recommended Cutting Speed: ≈40 cm/s Transfer Tape: FlexTape / transfer tape required Transfer Conditions:
Temperature: 295°F / 145°C Time: 18 – 20 sec. Pressure: medium / high Hot / warm peel of the transfer tape
Wash Resistance:
140°F / 60°C wash resistance
Available in: 19.7” x 5, 10, 25 yds. 29.5” x 5, 10, 25 yds. Call for additional roll widths and lengths, i.e. 54” & 59”
Garment Care: wash & dry garment inside out, machine wash & dry at low temperatures, see specification, “Wash Resistance” use mild detergents, No Chlorine, Do not dry clean Flex; Flock OK, wait 24 hours before first washing.
Store SEF Heat Transfer Materials in a cool and dry place; protect against the influence of light when stored. We recommend not to exceed a storage period of 24 months. Due to the variety of possible influences / exposure outside of our control, to include processing / use, all specifications should be viewed as reference values. We recommend a suitability test to the material before a production. Technical specifications rest on extensive tests and technical research, however, a legally binding warranty of specific characteristics and or performance cannot be provided.
10-Tatoo SBB App. Instr. v6 081515
ClearFlex – Application Instructions Printable Flex Film for Eco-Solvent & Solvent Inks Print Mirrored
ClearFlex is our most cost efficient digital print material. ClearFlex’s unique adhesive and polyurethane film construction allows the user to print in a mirror image and transfer directly to the textile with the films integrated polyester carrier. You do not need tranfer tape!
Suitable Inks:
ClearFlex’s unique construction allows for the digital image / ink to be protected between the film and the textile for extended color fastness / retention.
Eco-Solvent & Solvent
Special printing instructions:
Print mirror image Verify printing to the PU surface
Printer Profile Setting:
Roland, TTRH or HTM2, Garment Heat Transfer White or clear calendared matte or semigloss vinyl Printer mfg. settings for heat transfer material
Suitable Textiles:
ClearFlex can be printed with eco-solvent & solvent inks. To optimize the inks adhesion to the media, it is recommeded that the pre and post heat printer settings to be set at 110°F / 115°F. Print graphic as a mirror image! ClearFlex has a matte finish and is very thin with high elasticity resulting in a very light feel to the touch. Even large designs can be applied without wearing discomfort. Weed Graphic
Verify the printed design / ink is dry before making the transfer. Drying time is generally very quick, but it can take up to 5 hours or more based on the type of ink, ink density and ambient conditions. Finished graphics then can be transferred to the textile. Heat Pressing: You do not need transfer tape, the carrier is the transfer tape!
Heat Pressing: With the printed image facing down, carrier / liner up, “right reading”, apply the graphic to the textile and press for 15-17 seconds at 330°F / 165°C with medium to high pressure. Then remove the polyester liner / carrier using a hot or warm peel. Use a cold peel for an even softer feel. Washing resistance up to 140°F / 60°C.
Light colored textiles made of cotton, Cotton-polyester, blended textiles. Not suitable for coated textiles
Printer Dryer Setting:
Post heat: 110°F - 115°F
Cutting Conditions:
Blade: Relief angle 30 - 45° Blade pressure, med., 50 to 80 grams of down force. Test cuts recommended *Speed: ≈40 cm/s
No Transfer Tape / FlexTape Required Transfer Conditions;
Temperature: 330 °F / 165°C Time: 15 -17 seconds Pressure: medium / high Warm peel recommended Cold peel for an even softer feel
Wash Resistance:
140 °F / 60°C wash resistance
Available in:
19.7” x 5, 10, 25 & 50 yds. 29.5” x 5, 10, 25 & 50 yds.
Call for additional roll widths and lengths, i.e. 54” & 59”
Garment Care: wash & dry garment inside out, machine wash & dry at low temperatures, see specification, “Wash Resistance” use mild detergents, No Chlorine, Do not dry clean Flex; Flock OK, wait 24 hours before first washing.
Store SEF Heat Transfer Materials in a cool and dry place; protect against the influence of light when stored. We recommend not to exceed a storage period of 24 months. Due to the variety of possible influences / exposure outside of our control, to include processing / use, all specifications should be viewed as reference values. We recommend a suitability test to the material before a production. Technical specifications rest on extensive tests and technical research, however, a legally binding warranty of specific characteristics and or performance cannot be provided.
11-ClearFlex App. Instr. v6 081515
ClassicPrint - Application Instructions Economy Grade Printable Flex Film for Eco-Solvent, Solvent, Latex & UV Inks Print
ClassicPrint is an economy grade, production friendly, high-quality PVC print and cut media. The multi-layer film is carried on a polyester liner / carrier allowing for fast easy weeding. It has a matte finish with good elasticity and a good touch. Printable with eco-solvent, solvent, latex and UV inks. When printing with UV & latex inks, test prior to production.
Suitable Inks: Eco-Solvent, Solvent, Latex, UV Printer Profile Setting: Roland, TTRH or HTM2, Garment Heat Transfer White calendared matte or semigloss vinyl Printer mfg. settings for heat transfer material Printer Heat Settings, Pre & Post:
Cut
110°F – 115°F
Verify the printed design / ink is dry before applying our FlexTape transfer tape. Drying time is generally very quick but it can take up to 5 hours or more based on the type of ink, ink density and ambient conditions. After applying the FlexTape to the graphic, allow a minimum of 15 minutes before transferring the graphic to the textile. This will ensure good adhesion of the FlexTape to the printed image.
Suitable Textiles: Cotton, cotton – polyester & blended textiles. Not suitable for Nylon or coated textiles Cutting Conditions: Blade: Relief angle 45° optimum Blade pressure, med / high, 80 to 100 grams of down force. Test cuts recommended Cutting Speed: ≈40 cm/s Transfer Tape:
Transfer
Heat Transfer: With the image facing up, peel the transfer away from the liner / carrier. Apply the graphic to the textile and press for 17 seconds at 330°F / 165°C with medium to high pressure. Then remove the FlexTape using a hot or warm peel. Washing resistance up to 140°F / 60°C
FlexTape / transfer tape required Transfer Conditions:
Temperature: 330°F / 165°C Time: 17 sec. Pressure: medium / high Warm peel
Wash Resistance: 140°F / 60°C wash resistant Available in:
Transferring without transfer tape: It is possible to transfer connected designs without using transfer tape.
19.7” x 10, 25 & 50 yds. 29.5” x 10, 25 & 50 yds. Call for additional roll widths and lengths, i.e. 54” & 59”
Garment Care: wash & dry garment inside out, machine wash & dry at low temperatures, see specification, “Wash Resistance” use mild detergents, No Chlorine, Do not dry clean Flex; Flock OK, wait 24 hours before first washing.
Store SEF Heat Transfer Materials in a cool and dry place; protect against the influence of light when stored. We recommend not to exceed a storage period of 24 months. Due to the variety of possible influences / exposure outside of our control, to include processing / use, all specifications should be viewed as reference values. We recommend a suitability test to the material before a production. Technical specifications rest on extensive tests and technical research, however, a legally binding warranty of specific characteristics and or performance cannot be provided.
12-ClassicPrint App. Instr. v6 081515
EcoPrint – Application Instructions Printable Flock Film for Eco-Solvent & Solvent Inks EcoPrint is a white printable flock film specially formulated to accept and hold inks while maintaining excellent color fastness over extended washing cycles. EcoPrint offers a unique dimensional non-glare look and it is very soft to the touch as well as being very elastic, stretching with the textile. EcoPrint uses a polyester liner / carrier that allows for easy cutting & fast weeding.
Suitable Inks: Eco-Solvent, Solvent, Latex Printer Profile Setting: Roland, TTRH or HTM2 Garment Heat Transfer White calendared matte or semi-gloss vinyl Use printer mfg. settings for heat transfer material Printer Heat Settings, Pre & Post: 105°F to 115°F
Print and Cut
Weed Graphic
Transfer Design
EcoPrint is compatible with eco-solvent, solvent, latex inks. When printing with latex inks, we recommend testing prior to full production. Prior to printing, the media should be at 68°F to 80°F for optimum ink adhesion to the media. Verify the printed design / ink is dry before applying our FlockTape transfer tape. Drying time is generally very quick but it can take up to 3 hours or more based on the type of ink, ink density and ambient conditions. After applying the FlockTape to the graphic, allow a minimum of 15 minutes before transferring the graphic to the textile. This will ensure good adhesion of the FlockTape to the Printed image.
Suitable Textiles: Cotton, polyester, blended textiles Not suitable for coated textiles Cutting Conditions: Blade: Relief angle 45° - 60° Blade pressure, med., 60 to 100 grams of down force. Test cuts recommended Cutting Speed: ≈40 cm/s Transfer Tape: FlockTape
Layering Possible, Flock on Flex Transfer Condition:
Temperature: 330°F / 165°C Time: 15 - 17 sec. Pressure: medium low Hot, warm, cold peel of the transfer tape.
Wash Resistance: 104°F / 40°C wash resistance
With the image facing up, peel transfer away from the liner / carrier. Apply graphic to the textile and press for 15 - 17 seconds at 330°F / 165°C, medium low pressure. Remove the FlockTape using a hot, warm or cold peel.
Available in: 19.7” x 5, 10, 25 & 50 yds. 29.5” x 5, 10, 25 & 50 yds. Call for additional roll widths and lengths, i.e. 54” & 59”
Garment Care: wash & dry garment inside out, machine wash & dry at low temperatures, see specification, “Wash Resistance” use mild detergents, No Chlorine, Do not dry clean Flex; Flock OK, wait 24 hours before first washing.
Store SEF Heat Transfer Materials in a cool and dry place; protect against the influence of light when stored. We recommend not to exceed a storage period of 24 months. Due to the variety of possible influences / exposure outside of our control, to include processing / use, all specifications should be viewed as reference values. We recommend a suitability test to the material before a production. Technical specifications rest on extensive tests and technical research, however, a legally binding warranty of specific characteristics and or performance cannot be provided.
13-EcoPrint App. Instr. v6 081515
FiberPlus - Application Instructions Heat Transfer Polyester Flock Film for Sublimation Printing Print sublimation paper in mirror image
FiberPlus is a micro-fiber flock film specifically formulated to receive inks by way of the sublimation transfer process. The polyester micro fibers absorb and retain color fastness through extended washing cycles when using proper washing & drying care.
Suitable Inks: Sublimation Inks Printer Profile Setting: Specific to ink and printer & paper used Suitable Textiles:
When using the sublimation heat transfer process, the previously mirrored printed image, printed on sublimation paper, is then transferred onto FiberPlus at 375 to 410°F for 30 to 40 seconds using low pressure. The designs are cut on a plotter / cutter using registration marks to support cutting accuracy, or simply hand cut. After applying FlockTape transfer tape and the designs are removed from the carrier and applied to the textile at 330°F / 165°c for 15 to 17 sec. using low pressure.
Cotton, cotton – polyester & blended textiles. Not suitable for nylon or coated textiles Cutting Conditions: Blade: Relief angle 45° optimum Blade pressure, med, 60 to 80 grams of down force. Test cuts recommended Cutting Speed: ≈40 cm/s Transfer sublimation image to FiberPlus
Sublimation to FiberPlus: Temperature: 375 to 410°F Time: 30 to 40 sec. Pressure, Medium / low Transfer Tape: FlockTape transfer tape required
FiberPlus is suitable for cotton, cotton – polyester and blended fabric. It is not suitable for nylon and other coated textiles. It is wash resistant up to 140°F / 60 °C. Available in rolls and also A3 & A4 sheets, 50 sheets per box.
Cut and transfer to textile
Transferring without transfer tape: It is possible to transfer connected designs without using transfer tape.
Heat Transfer to textile:
Temperature: 330°F / 165°C Time: 17 sec. Pressure: low Warm peel of transfer tape
Wash Resistance: 140°F / 60°C wash resistant Available in: 19.7” x 5 & 10 yds. A3, box of 50 sheets A4, box of 50 sheets Call for additional roll widths and lengths
Garment Care: wash & dry garment inside out, machine wash & dry at low temperatures, see specification, “Wash Resistance” use mild detergents, No Chlorine, Do not dry clean Flex; Flock OK, wait 24 hours before first washing.
Oeko-Tex® Product Class I
Store SEF Heat Transfer Materials in a cool and dry place; protect against the influence of light when stored. We recommend not to exceed a storage period of 24 months. Due to the variety of possible influences / exposure outside of our control, to include processing / use, all specifications should be viewed as reference values. We recommend a suitability test to the material before a production. Technical specifications rest on extensive tests and technical research, however, a legally binding warranty of specific characteristics and or performance cannot be provided.
14-FiberPlus App. Instr. v6 081515
Graffiti – Application Instructions Printable Flex Film for Eco-Solvent, Solvent, Latex & UV Inks Graffiti is a high-quality, matte / semi-gloss, white multi-layer polyurethane film on a polyester liner / carrier. Graffiti is a very thin super soft film with high opacity. Graffiti does not require pre-heating, however, the media should be at 68°F to 80°F for optimum ink adhesion to the media. Graffiti is compatible with eco-solvent, solvent, latex & UV inks. Apply FlexTape
Suitable Inks: Eco-Solvent, Solvent, Latex, UV Printer Profile Setting: Roland, TTRH or HTM2, Garment Heat Transfer White calendared matte or semi-gloss vinyl Printer mfg. settings for heat transfer material Suitable Textiles:
Verify the printed design / ink is dry Print and Cut before applying our FlexTape transfer tape. Drying time is generally very quick but it can take up to 5 hours or more based on the type of ink, ink density and ambient conditions. After applying the FlexTape to the graphic, allow a minimum of 15 minutes before transferring the graphic to the textile. This will ensure good adhesion of the FlexTape to the printed image.
Cotton, cotton – polyester & blended textiles. Not suitable for Nylon or heavily coated textiles
Heat Transfer, Option 1: With the image facing up, peel the transfer away from the liner / carrier. Apply the graphic to the textile and press for 17 seconds at 330°F / 165°C with Hot or Warm Peel medium to high pressure. Then remove the FlexTape using a hot or warm peel. Washing resistance up to 104°F / 40°C.
Transfer Tape:
Heat Transfer, Option 2: Alternate pressing method which can provide higher washing resistance, up to 140°F / 60°C. With the image facing up, peel transfer away from the liner / carrier. Apply graphic to the textile and press for 5-7 seconds at 330°F / 165°C, medium to high pressure. Remove the FlexTape using a hot or warm peel. Do a second pressing without the transfer tape for 15 seconds at 330°F / 165°C.
Heat Settings, Pre & Post: Switched off or lowest settings Cutting Conditions: Blade: Relief angle 30° or 45° Blade pressure, med., 50 to 80 grams of down force. Test cuts recommended Cutting Speed: ≈40 cm/s FlexTape / transfer tape required Transfer, Option 1:
Temperature: 330°F / 165°C Time: 17 sec. Pressure: medium / high Hot or warm peel the transfer tape, washing resistance, 104°F / 40°C
Wash Resistance: Option 1 will provide a washing resistance 104°F / 40°C For higher washing resistance of 140°F / 60°C use transfer option 2 Available in: 19.7” x 5, 10, 25 & 50 yds. 29.5” x 5, 10, 25 & 50 yds. Call for additional roll widths and lengths, i.e. 54” & 59”
Garment Care: Wait 24 hours before first washing, wash & dry garment inside out, machine wash & dry at low temperatures, see specification, “Wash Resistance” use mild detergents, No Chlorine, do not dry clean Flex; Flock OK.
Store SEF Heat Transfer Materials in a cool and dry place; protect against the influence of light when stored. We recommend not to exceed a storage period of 24 months. Due to the variety of possible influences / exposure outside of our control, to include processing / use, all specifications should be viewed as reference values. We recommend a suitability test to the material before a production. Technical specifications rest on extensive tests and technical research, however, a legally binding warranty of specific characteristics and or performance cannot be provided.
15-Graffiti App. Instr. v6 081515
Graffiti – Application Instructions Graffiti Transfer Recommendations That Have Yielded Positive Results! Graffiti should be cut with a 30 or 45 degree "sharp" blade at approximately 50 to 80 grams of down force. If you are using more down force than 80 grams, change your blade out for a new one. We recommend that you always do a test cut before starting a production. A dull blade will make for more difficult weeding and transferring of a graphic. For Information on cutting tips, you can visit our company‘s Blog: (http://sefamericas.blogspot.com), articles / Bulletins, i.e. Plotter Cutting Heat Transfer Films Procedure for masking and peeling of graphics from the carrier as follows: 1. We recommend waiting at least 30 minutes for the printed graphic to dry before applying the transfer tape. Drying could take longer based on ink density, the ambient temperature and humidity in the shop. 2. Apply the transfer tape and allow 15/30 minuntes for the transfer tape to set up. Adhesives build over time. 3. Before peeling the graphic, re-squeegee the graphic firmly, then with the graphic laying on the table "image facing up" (see pictures), lift the transfer tape up and away from the liner / carrier. If the transfer tape picks the graphic up OK with a 15/30 minutes dwell time, you can shorten the waiting period.
Garment Care: Wait 24 hours before first washing, wash & dry garment inside out, machine wash & dry at low temperatures, see specification, “Wash Resistance” use mild detergents, No Chlorine, do not dry clean Flex; Flock OK.
Store SEF Heat Transfer Materials in a cool and dry place; protect against the influence of light when stored. We recommend not to exceed a storage period of 24 months. Due to the variety of possible influences / exposure outside of our control, to include processing / use, all specifications should be viewed as reference values. We recommend a suitability test to the material before a production. Technical specifications rest on extensive tests and technical research, however, a legally binding warranty of specific characteristics and or performance cannot be provided.
15-Graffiti App. Instr. v6 081515
