Electrochemical and Solid-State Letters, 10 共10兲 G76-G79 共2007兲

G76

1099-0062/2007/10共10兲/G76/4/$20.00 © The Electrochemical Society

Damage Reduction and Sealing of Low-k Films by Combined He and NH3 Plasma Treatment A. M. Urbanowicz,a M. R. Baklanov,a,z J. Heijlen,a Y. Travaly,a and A. Cockburnb a

IMEC, Leuven, Belgium Applied Materials, Leuven, Belgium

b

Modification of chemical vapor deposition low-k films upon sequential exposure to helium plasma and then ammonia plasma is characterized using various methods. The He plasma emits extreme ultraviolet 共EUV兲 photons creating O2 vacancies, which impacts surface reactive sites and induces localized chemical modifications in the first surface monolayers. The subsequent NH3 plasma treatment provides complete sealing of the low-k surface. The depth of the modification, which is a factor of merit of the sealing process, is limited because of the high absorption coefficient of silica-based low-k materials in the range of EUV emission. © 2007 The Electrochemical Society. 关DOI: 10.1149/1.2760189兴 All rights reserved. Manuscript submitted May 14, 2007; revised manuscript received June 21, 2007. Available electronically July 31, 2007.

Integration of porous low dielectric constant 共low-k兲 materials is a continuing issue in microelectronics industry. One of the most difficult challenges is related to the high sensitivity of porous materials to chemicals and plasma. Pores and their connectivity significantly increase the penetration depth of active species during different technological processes such as plasma etching and cleaning, deposition of barrier layers, chemical mechanical polishing 共CMP兲, etc. The most severe damage of low-k materials happens during their exposure to strip-cleaning plasmas containing oxygen and hydrogen radicals. These radicals remove the carbon containing hydrophobic groups from the low-k materials. As a result of the carbon depletion, the films become hydrophilic.1,2 Subsequent moisture absorption in the pores significantly increases the k value because of the high polarizability of water molecules. Recently, we have applied a diffusion-recombination model 共Thiele analysis兲 to predict and quantify the plasma damage of porous low-k materials.3 The penetration depth of radicals into porous low-k materials and the depth of plasma damage depend on the Thiele modulus, ␭, defined as follows 共Eq. 1兲 ␭ = 共4kr /d pDA兲1/2

关1兴

where kr is the sum of reaction constants consuming active radicals on pore wall. DA and d p are diffusion coefficient and pore diameter, respectively. The higher the Thiele modulus, the lower the depth of penetration of active radicals. Because kr is mainly defined by the recombination of active radicals, the depth of plasma damage can be significantly reduced by stimulating the surface recombination of active radicals. The creation of surface active centers initiates the recombination of oxygen and hydrogen radicals and reduces the plasma damage. As an example, we showed that treatment of low-k materials in He plasma significantly reduces plasma low-k damage during the subsequent exposure to strip and cleaning plasmas. It was speculated that extreme ultraviolet 共EUV兲 emission from He plasma creates chemically active sites on a low-k surface, which stimulate the recombination of active radicals in the surface area. In certain cases the activated surface area can stimulate and induce localized chemical reactions results in the sealing of low-k materials. In this work, the modification of the top part of low-k films treated by He and NH3 plasmas is characterized by various methods. This plasma is normally used to clean the Cu surface 共reduce Cu oxides兲 before dielectric barrier deposition. In the absence of a dielectric protection layer, low-k films are exposed to this plasma during the Cu cleaning, which ultimately results in significant degradation of k values. The effect of He plasma pretreatment is studied as a function of exposure times. The changes in the chemical composition of low-k films after the plasma exposure are analyzed using

z

E-mail: [email protected]

Fourier transform infrared spectroscopy 共FTIR兲 and time-of-flight secondary ion mass spectroscopy 共ToF-SIMS兲 measurements. The layered structure of the modified surface is evaluated by X-ray reflectivity 共XRR兲 and spectroscopic ellipsometry. The sealing properties of the cap layer were evaluated by ellipsometric porosimetry 共EP兲 with a toluene source. Hydrophilicity of the films is evaluated by contact angle measurements, FTIR and EP with water source 共WEP兲. We discuss the mechanisms of plasma damage reduction, densification, and sealing of chemical vapor desposition 共CVD兲 lowk material after consecutive treatment of CVD low-k material by He and NH3 plasma. Experimental Materials.— The low-k material used in this study is a porous carbon doped silica film 共SiCOH兲 deposited by plasma enhanced chemical vapor deposition 共PECVD兲 on top of 300 mm silicon substrates. The low-k film has an open porosity close to 25% and a pore radius 0.8–0.9 nm, as measured by EP,4 a dielectric constant in the range of 2.4–2.5, and a refractive index of 1.33 at 633 nm. The plasma treatment was carried out at 350°C in the PECVD chamber. The wafers were subjected to NH3 plasma for 20 s under a pressure of 4.2 Torr. Instrumentation.— Porosity, pore size distribution, and bulk hydrophilicity were measured by using ellipsometric porosimeter EP-10 equipped with the Sentech 801 spectroscopic ellipsometer 共␭ = 350–850 nm兲. The ellipsometer was mounted on a vacuum chamber that can be filled with solvent vapor 共such as toluene or water兲 in a controllable way.3-5 Similar EP measurements, as described by Shamiryan et al.,6 were also used for the evaluation of the sealing efficiency of the dense surface layers formed after surface treatment. The last method is based on the idea that, if the surface contains open pores, the solvent is adsorbed in the pores and it changes the ellipsometric angles ⌬ and ⌿. On the contrary, if the surface is not accessible to a solvent due to the presence of a sealing layer, ⌬ and ⌿ remain unchanged during the exposure to toluene vapor. The chemical composition and bonding structure of low-k films before and after plasma treatments were analyzed using a Biorad QS2200 ME FTIR system. ToF-SIMS experiments were carried out using an Iontof IV instrument in a non-interlaced dual beam mode with a Xe sputtering beam and a bunched 15 keV Ga analysis beam to detect secondary ions. The Ga analysis beam has been rastered over a 100 ⫻ 100 ␮m area. The Xe sputtering beam was used with 1 keV of impact energy and 80 nA of current using a raster size of 500 ⫻ 500 ␮m. The sputtering times were converted into the thickness using spectroscopic ellipsometry 共SE兲 data. The XRR technique was used for the evaluation of the density gradients.7 High-resolution specular X-ray reflectivity was performed using a ␪/2␪ configuration with a rotating copper anode as

Downloaded 30 Sep 2008 to 146.103.254.11. Redistribution subject to ECS license or copyright; see http://www.ecsdl.org/terms_use.jsp

Electrochemical and Solid-State Letters, 10 共10兲 G76-G79 共2007兲

Figure 1. FTIR spectra of the low-k films treated by He and NH3 plasmas.

the radiation source using a Siemens D5000 2-circles goniometer. X-rays of 1.5418 Å wavelength 共Cu K␣兲 were selected by a graphite secondary monochromator, complemented with an electronics discriminator 共scintillation counter兲. The X-ray beam is collimated by a set of adjustable slits with micrometer precision. The intensity reflected is measured as a function of detector angle 共␪兲 and subsequently plotted vs the momentum transferred perpendicularly to the sample 关共2␲/␭兲 sin ␪兴. The data treatment has already been described in the literature.8 Results and Discussion Figure 1 shows FTIR spectra of the low-k film before and after exposure to the various plasmas. The top graph of the figure shows FTIR spectra of a pristine sample in the range of 800–1400 cm−1. The FTIR spectra are typical of SiCOH-type materials and contain a peak related to Si–O–Si network 共1040–1060 cm−1兲, a shoulder of a cagelike structure 共1100–1150 cm−1兲, and a peak related to Si–CH3 bond 共1250–1300 cm−1兲.9 No absorption related to moisture 共3000–3700 cm−1兲 was observed in the pristine low-k films. This is in agreement with the results of WEP evaluation showing that the amount of moisture adsorbed does not exceed 1% at 100% humidity. The differential spectra 共bottom graphs兲 reflect that changes occur after successive exposure to He and NH3 plasmas and are plotted at the bottom of the Fig. 1. The peak at 1275 cm−1, which arises from Si–CH3 groups, decreases after all plasma treatments. The negative peak located close to 1150 cm−1 is related to the Si–O–Si 共angle ⬃150°兲 cagelike structure. The positive peak around 1070 cm−1 共angle ⬃144°兲 is related to the Si–O–Si network. The highest positive maximum of the network peak appears after pure NH3 plasma. The peak around 1000 cm−1 arises from the Si–O–Si suboxide9 共angle ⬍144°兲. This peak only appears after He plasma treatment. The amplitude of this peak increases with the time of the plasma treatment. The smallest amplitude appears after successive exposure in He 共20 s兲 and NH3 共20 s兲 plasmas. The appearance of the suboxide peak may be related to the formation of oxygen vacancies in the low-k film. Figures 2a-d show the results of the EP analysis of pristine and plasma-treated samples. These graphs reflect the amount of toluene adsorbed vs its relative pressure. Pristine low-k film has 25% of open porosity. The open porosity slightly increases after NH3 plasma treatment. The film exposure in NH3 plasma does not change the pore size. He plasma treatment reduces the open porosity by 2%. However, toluene cannot be completely desorbed during the pumping-down cycle, and the hysteresis loop observed suggests a delay in the pore filling and emptying during the adsorption and

G77

desorption cycles 共Fig. 2c兲. At the same time, a slight change of refractive indices 共1.33 before and 1.36 after sealing兲 suggests that the total porosity does not significantly change, which indicates that the bulk of the film is still porous. Therefore, diffusion limitation of the toluene penetration is only related to densification of the top part of the film, i.e., “partial” sealing of the pores. The partial sealing means a decrease of the size of the pore necks and the complete sealing of some pores. In this case, it is not possible to calculate the pore size distribution. We can only conclude that the effective pore size in the top part of the film 共necks兲 becomes comparable with the size of the toluene molecules 共0.65 nm兲. Figure 3 shows the “delay” between toluene adsorption and desorption ␶共1/2兲 vs time of the He plasma treatment. The ␶共1/2兲 is the difference between two values of P/Po 共Fig. 2c兲 corresponding to the conditions when the pores are filled for 50%. In all experiments the rate of the pressure change was the same. Therefore, this delay reflects change of the toluene diffusion rate through the capping layer and the degree of surface densification 共sealing兲. The longer delay corresponds to the smaller size of remaining pores. The delay increases with time of He plasma treatment. Therefore, Fig. 3 allows us to conclude that the degree of densification depends on the time of He plasma treatment. Porous low-k films after the successive He and NH3 plasma treatment do not show any toluene absorption 共Fig. 2d兲. This indicates that complete sealing of the dielectric surface was achieved. Figure 4 shows ToF-SIMS carbon depth profile in low-k films after different plasmas. A 20 s NH3 plasma creates a huge carbon depletion over a depth of about 60 nm. The degree of carbon depletion is very small for a low-k film after He plasma. In the case of 20 s He plasma followed by 20 s NH3 plasma treatment, the carbon depletion is significantly lower than after the NH3 plasma without the pretreatment in He plasma. Figure 5 shows the XRR density profile of the low-k film exposed in He plasma. The bulk density is constant and equal to the density of the pristine material 共1.13 g/cm3兲. The top of the film has a higher density. The thickness of the densified layer is close to 17 nm. The double peak between 150 and 167 nm reflects the density fluctuation in the capping layer. These data demonstrate that He plasma creates a thin densified layer in the top part of the low-k film. The densified layer is manifested by the toluene diffusion limitation in EP measurements and clearly visible in XRR data as a top layer with a thickness close to 17 nm. The results of differential FTIR analysis suggest that this top layer is oxygen depleted in comparison with the bulk of the film. The degree of the carbon depletion after He plasma is very small. Moreover, a He pretreatment before NH3 plasma drastically reduces the plasma damage and improves the sealing efficiency. Porous lowk films after the successive He and NH3 plasma treatments do not show any toluene absorption. This indicates that the complete sealing effect of the dielectric surface is achieved. The effect of the damage reduction when the low-k film has not been sealed and He was used before N2 /NH3 plasma was reported earlier.3,10 It was speculated that the He plasma creates surface active centers increasing the recombination probability of H radicals and, therefore, decreases their concentration and depth of penetration. The results presented in this paper support these conclusions, but also allow us to postulate that these active centers localize different chemical transformations in the top part of the film. Therefore, these centers are also able to accelerate chemical reactions responsible for the surface sealing. Effect of He plasma.— The most important factors of plasma processing are pressure, chemistry, temperature, and bias potential. Because helium is a light noble gas, the modification based on chemical reactions is excluded and the impact of ion bombardment is also expected to be much lower than in other gases like Ar, N2, etc. The most probable modification of the low-k material is related to EUV light generated by He plasma. The modification of SiO2 layers caused by EUV radiation from He plasma has been reported.11,12 It was shown that EUV light is able to break the Si–O

Downloaded 30 Sep 2008 to 146.103.254.11. Redistribution subject to ECS license or copyright; see http://www.ecsdl.org/terms_use.jsp

G78

Electrochemical and Solid-State Letters, 10 共10兲 G76-G79 共2007兲

Figure 2. Open porosity 共as measured by EP兲: 共a兲 pristine sample, 共b兲 after NH3 plasma, 共c兲 after He plasma, 共d兲 He + NH3 plasma.

bond on the SiO2 surface and to form so-called E⬘ defects 共oxygen vacancies兲. The energy needed to create an oxygen vacancy in SiO2 is equal to 11 eV 共112.71 nm兲 and 22 eV 共56.36 nm兲.13 The bandgap of low-k materials is smaller than that of SiO2 共⬇8 eV against 8.8 eV兲,14 which is significantly smaller than the energy of EUV photons from He plasma 共24.59 eV兲.15 These photons generate free electron and holes by the band-to-band excitation that result in the cleavage of strained Si–O binds via self-trapped excitons.16 The

Figure 3. Delay between adsorption and desorption isotherms of toluene 共calculated from EP data兲 for different times of the He plasma treatment.

bond cleavage induces the rearrangement of the strained Si–O–Si bonds, which cause the densification of the film.17 Thickness of the densified layer is of the order of magnitude of the penetration depth of EUV light into a low-k film. Using absorption coefficients reported by Philipp et al.,18 one can calculate the penetration depth of EUV photons from He plasma into the silica. These calculations show that the intensity of EUV light with wavelength of 60–100 nm decreases to 1/e within the first 10 nm of silica. Therefore, one can conclude that most photochemical modifications of silica-based low-

Figure 4. The carbon depth profile analyzed by ToF-SIMS.

Downloaded 30 Sep 2008 to 146.103.254.11. Redistribution subject to ECS license or copyright; see http://www.ecsdl.org/terms_use.jsp

Electrochemical and Solid-State Letters, 10 共10兲 G76-G79 共2007兲

G79

close to 17 nm. The depth of the modification is limited because of the high absorption coefficient of silica-based low-k materials in the range of EUV emission of He plasma. The He plasma treatment also reduces plasma damage even when the low-k dielectric film is not sealed.3,10 If this is the case, the modified layer increases the recombination probability of active radicals and, therefore, decreases their concentration and depth of penetration into low-k materials. Properties of EUV emission from He and He/H2 plasma can be very important in development of technological processes with reduced damage during the plasma processing. Acknowledgments It is our pleasure to thank F. Alexis and T. Conard for ToF-SIMS and XPS analysis. IMEC assisted in meeting the publication costs of this article.

References Figure 5. Results of XRR analysis of a 40 s He plasma-treated 160 nm thick low-k film.

k film are restricted by 10–20 nm of the top layer. One can see that this thickness is in reasonably good agreement with XRR data, which showed densification of the top 17 nm. Additional NH3 plasma treatment completes the sealing 共Fig. 2d兲. According to XPS analysis,19 the “crust” layer formed as a result of consecutive treatment in He and NH3 plasmas shows insignificant increase of nitrogen concentration in the top layer 共2–3 atom %兲. The low-k films after this treatment still show high degree of surface and bulk hydrophobicity, which is a proof of low degree of plasma damage. More detailed data analysis will be reported in our future paper.19 Therefore, EUV light from He plasma results in formation of surface active centers localizing chemical reactions to the surface and providing the backbone reorientation and further densification of the top layer. Conclusion He plasma emits high-energy EUV photons, creating oxygen vacancies that localize chemical modifications in the top part of the film. The subsequent NH3 plasma treatment provides the complete sealing of the low-k surface. The thickness of the densified layer is

1. K. Maex, M. R. Baklanov, D. Shamiryan, F. Iacopi, S. H. Brongersma, and Z. S. Yanovitskaya, J. Appl. Phys., 93, 8793 共2003兲. 2. M. A. Worsley, S. F. Bent, S. M. Gates, N. C. M. Fuller, W. Volksen, M. Steen, and T. Dalton, J. Vac. Sci. Technol. B, 23, 395 共2005兲. 3. M. R. Baklanov, K. P. Mogilnikov, V. G. Polovinkin, and F. N. Dultsev, J. Vac. Sci. Technol. B, 18, 1385 共2000兲. 4. M. R. Baklanov and K. P. Mogilnikov, Microelectron. Eng., 64, 335 共2002兲. 5. M. R. Baklanov, K. P. Mogilnikov, and Q. T. Le, Microelectron. Eng., 83, 2287 共2006兲. 6. D. Shamiryan, M. R. Baklanov, and K. Maex, J. Vac. Sci. Technol. B, 21, 220 共2003兲. 7. A. Van der Lee, Solid State Sci., 2, 257 共2000兲. 8. Y. Travaly, J. Schuhmacher, A. M. Hoyas, T. Abell, V. Sutcliffe, A. M. Jonas, M. Van Hove, and K. Maex, Microelectron. Eng., 82, 639 共2005兲. 9. A. Grill and D. A. Neumayer, J. Appl. Phys., 94, 6697 共2003兲. 10. A. M. Urbanowicz, A. Humbert, G. Mannaert, Z. Tokei, and M. R. Baklanov, Solid State Phenom., In press. 11. K. Yokogawa, Y. Yajima, T. Mizutani, S. Mishimatsu, and K. Suzuki, Jpn. J. Appl. Phys., Part 1, 29, 2265 共1990兲. 12. T. Tatsumi, S. Fakuda, and S. Kadomura, Jpn. J. Appl. Phys., Part 1, 33, 2175 共1994兲. 13. G. Cerofolini, in Adsorption in Silica Surface, M. Dekker, Editor, p. 369, CRC Press, Boca Raton, FL 共2000兲. 14. P. Marsik, P. Verdonck, D. Schneider, D. De Roest, and M. R. Baklanov, Phys. Status. Solidi, Submitted. 15. A. R. Striganov and N. S. Sventitskii, in Tables of Spectral Lines of Neutral and Ionized Atoms, IFI/Plenum, New York 共1968兲. 16. A. L. Shluger, J. Phys. C, 21, L431 共1988兲. 17. H. Imai, M. Yasumori, H. Hirashima, K. Awazu, and H. Onuki, J. Appl. Phys., 79, 8304 共1996兲. 18. H. R. Philipp, in Handbook of Optical Constants of Solids, E. D. Palik, Editor, Part II, pp. 749–766, Academic Press, Orlando, FL 共1985兲. 19. A. Urbanowicz and M. R. Baklanov, Unpublished.

Downloaded 30 Sep 2008 to 146.103.254.11. Redistribution subject to ECS license or copyright; see http://www.ecsdl.org/terms_use.jsp

Damage Reduction and Sealing of Low-k Films by ...

A. M. Urbanowicz,a M. R. Baklanov,a,z J. Heijlen,a Y. Travaly,a and. A. Cockburnb. aIMEC, Leuven, Belgium. bApplied Materials, Leuven, Belgium. Modification of chemical vapor deposition low-k films upon sequential exposure to helium plasma and then ammonia plasma is characterized using various methods. The He ...

428KB Sizes 0 Downloads 170 Views

Recommend Documents

Damage Reduction and Sealing of Low-k Films by ...
electron and holes by the band-to-band excitation that result in the cleavage of ... nificant increase of nitrogen concentration in the top layer (2–3 atom. %).

Uncertainty Reduction of Damage Growth Properties Using ... - UFL MAE
prognosis techniques, it is necessary to incorporate the measured data into a damage .... with initial half-crack size ai subjected to fatigue loading with constant ...

lagoon sealing and filter cakes
Long-term studies with other soil and waste types are needed to confirm the findings of this ... Submitted for review in September 2005 as manuscript number SE. 6058 ... Chapman Dr., Knoxville, TN 37996; phone: 865-974-7130; fax: 865-. 974-4514 ....

Apparatus and method for sealing vascular punctures
Oct 22, 1993 - (US); Hans Mische, St. Cloud, MN (US) .... 4,168,708 A * 9/1979 Lepley, Jr. et al. 5,035,695 A * 7/1991 ... 4,404,971 A * 9/1983 LeVeen et al.

Localized deposition of zinc oxide films by automated ...
dependent on the solution composition and substrate temperature. Solution-dispensed films have been ... alternative approach to the deposition of metal oxide films involves localized ..... optical constants as a function of photon energy. The.

Kinetics of Reduction of Nitrochlorobenzenes by ...
of nitroarenes and the rate of reduction increases in presence of electron ... the electron donating (due to resonance by lone pair electron of chlorine atom).

Kinetics of the reduction of nitrotoluenes by aqueous ...
sulfur produced in their sulfur recovery units (SRUs). There- .... Shimadzu C-R6A Chromatopac data processor was used for the ..... Houston, Texas, 1997.

Kinetics of Reduction of Nitrotoluenes by H2S-Rich ...
Kinetics of Reduction of Nitrotoluenes by H2S-Rich Aqueous Ethanolamine. Sunil K. ... pressure of alkanolamines can make the operation more flexible, in terms ...

17-08-022. Disaster Risk Reduction Reduction and Management ...
17-08-022. Disaster Risk Reduction Reduction and Management Program.pdf. 17-08-022. Disaster Risk Reduction Reduction and Management Program.pdf.

Preparation and Optical Characterization of ZnO-Pr films
Nov 28, 1998 - The carbonates of Zn and Pr were co-precipitated by adding ammonium carbonate. This precipitate was filtered, dried and calcined at 900 o. C overnight. The homogeneity of the oxides thus recovered was checked using X-ray diffraction. O

Peak Power Reduction and Workload Balancing by ...
May 29, 2013 - demand-supply matching requires on-chip power converters [5, ..... th of group gi, the slack can be calculated by ai j = Pe(Ti j ) − Pi th. (9).

Reduction of Nitrotoluenes by H2S-rich Aqueous ...
problems in subsequent processing steps such as: corrosion of process equipment, .... R6A Chromatopac data processor was used for the analysis. The column ...

Reduction of p-nitrotoluene by aqueous ammonium ...
The present work deals with a detailed study of the commer- ... the presence of C C, azo, other nitro groups, or any other func- tional group ..... 11, a good agree-.

Case study of vibration damage
column apple pack seem valuable and pioneering. .... Leuven fruit orchard (Deli et al., unpublished data). Fig. 1 ... In later analysis of the distribution of the bruise.

1 Damage and failure mechanism of concrete-filled ...
CFRP box filled with concrete and will act under transverse and axial loads for a large scale structural application as a modular ... However, the input. 1 Structural Engineer, Butwal Power Company Limited. .... A general purpose FEA software Marc wa

Evaluation of plasma damage in blanket and patterned ...
low-k agree well with the FTIR and water source ellipsometric porosimetry (WEP) ... be used for the real-time process optimization and monitoring. Therefore, it is ...

Theology-And-The-Films-Of-Terrence-Malick-Routledge-Studies-In ...
are simple on the eyes, some possess a ton of ... THE FILMS OF TERRENCE MALICK. Read On the web and Download Ebook The Films Of Terrence Malick. Download James Morrison ebook file totally free and. this ebook pdf present at Wednesday 29th of December

Impact of Ion Implantation Damage and Thermal ...
on simulation results using UT–MARLOWE 5.0, a software platform for Monte Carlo ... profiles were generated to represent the degree of amorphiza- tion in the ..... [14] A. Tasch et al.. (1999) UT–MARLOWE 5.0 Manual. [Online]. Avail- ... Universit

polyparasitism and damage of small ruminants ...
Author of correspondence; Email: [email protected]. Abstract: Parasitic diseases cause loss of productivity .... The Mc Master slide was filled in with liquid taken by the filtrate with a Paster pipet [13]. The Mc Master slide was examined under a

Fences and Deer-Damage Management: A Review of ...
vice/Wildlife Services/National Wildlife Research Center. †United States ..... preserves, game farms, and areas with potential for extreme deer damage (Craven ...

pdf-1414\films-of-makhmalbaf-cinema-politics-and-culture-in-iran-by ...
Connect more apps... Try one of the apps below to open or edit this item. pdf-1414\films-of-makhmalbaf-cinema-politics-and-culture-in-iran-by-eric-egan.pdf.