P14 Power Supply Instruction Beijing Reci Laser released the new SMART power supply in 2013. It can monitor laser machine’s working status in time and show that information in display screen in many languages. End users or unprofessional people can check the information and find reasons for malfunction by machines easily, which can reduce a lot of after sale service costs.
2.Wiring diagram
It is not only a good power supply we sale, It is a good solution for after sales we provide. 1. Highlights • Wide Input Range (90v-250v): it equals to put a
voltage regulator and stabilizer in power supply, which can be used under different input voltages in different countries or outputs stabile current under instable input voltage. • Short Circuit Protection: when positive and negative poles short-circuits, power supply will cut off the circuit automatically for protection. • Open Circuit Protection: when positive and negative poles open-circuits, power supply will cut off the circuit automatically for protection. • Input Enable Signal Detection: show electrical signal from machine’s control board • Temperature/Humidity Detection: self-protection starts when temperature or humidity is over permit value to ensure the safety of laser operation • Working Status Detection: monitor electrical signal from laser tube in time and analyze its working status • Malfunction analysis: analyze disorders by machines/ laser tubes and show that information on screen in different languages • NOTICE: Please deal with the malfunction according to the given solutions showing in screen firstly. Power supply can be used again only if it is powered off and restarted.
3. Wiring instructions ① Footer 1 is 5V power supply. (Not needed when connecting the cardinal plate. It is used when regulating the power with potentiometer and the 5V current should be less than 20 mA. ② TH. TL refers to high and low power level respectively, and WP refers to water protection. ③ Footer 5 G refers to ground, and 6 refers to input end. ④ When connecting the control plate, connect the light signal with footer 2 in the case of high power level light-emitting, (footer 3 for low power level light-emitting), connect the ground-wire with footer 5, connect footer 6 with power control analog signal, and make short circuit for footer 4 and 5. ⑤ For testing: 3, 4 and 5 are in short circuit (or 4, 5 are in short circuit and 3, 5 are connected to switch), the potentiometer center is connected with 6 IN, and the two other ends are connected to 5V and ground (1 and 5) respectively. ⑥ The high power level controls the light, 1 and 2 are connected, and 4 and 5 are in water protection. ⑦ It is not proposed to control laser power with high-frequency modulation, because it will have impact on the service life of the laser. ⑧ The model is applicable to Z4 laser tube, it is necessary to regulate and use the current according to the laser instructions. ⑨ The ammeter is concatenated to the cathode line.
unprofessional people can check the information and find reasons for malfunction ... Input Enable Signal Detection: show electrical signal from machine's control ...
can reduce a lot of after sale service costs. It is not only ... Short Circuit Protection: when positive and negative ... Temperature/Humidity Detection: self-protection.
Retrying... Download. Connect more apps... Try one of the apps below to open or edit this item. P14 Cristalls d'ADP.pdf. P14 Cristalls d'ADP.pdf. Open. Extract.
Multi-megabyte instruction working sets of server work- loads defy the ... proposed dedicated prefetching techniques aimed sepa- rately at L1-I and BTB, ...
There was a problem previewing this document. Retrying... Download. Connect more apps... Try one of the apps below to open or edit this item. 1º Psp Rqcta ...
Download. Connect more apps... Try one of the apps below to open or edit this item. PSU (Power Supply Unit).pdf. PSU (Power Supply Unit).pdf. Open. Extract.
in position 2. Multiple LTC2937s can share sequence position information, so that sequence position N happens at the same time for all LTC2937 chips, and.
There was a problem previewing this document. Retrying... Download. Connect more apps... Try one of the apps below to open or edit this item. power supply ...
There was a problem previewing this document. Retrying... Download. Connect more apps... Try one of the apps below to open or edit this item. 2º Psp Rcqta ...
There was a problem previewing this document. Retrying... Download. Connect more apps... Try one of the apps below to open or edit this item. 2º Psp P14 - Sta ...
FERIADO - 20-jun 21-jun 22-jun 23-jun 24-jun. 27-jun 28-jun 29-jun 30-jun 01-jul. 04-jul 05-jul 06-jul 07-jul FERIADO - 08-jul. T. Psp. III HumanÃstica. Sede Santa Fe 16 a 20 hs. Prof. Alloatti. PsicologÃa y Relaciones Humanas. Sede Santa Fe - 17 a
Page 1. Whoops! There was a problem loading more pages. Retrying... 3º Lic. Com - 2016 P14.pdf. 3º Lic. Com - 2016 P14.pdf. Open. Extract. Open with. Sign In.
A third alternative with electric motors, stand-alone boilers and purchase of ... compressors and build an on-site combined heat and power. (CHP) plant, or to ...
Master/slave channels are enabled via the master's enable pin and regulate to the master's feedback network. Output current can be increased to 3A or 4A by ...