GOVERNMENT INDUSTRIAL TRAINING INSTITUTE – TRICHY 14 TRADE : FITTER SEMESTER – I REVISION TEST - I
TIME : 3hrs
MARKS: 150
1) For cutting the thread of M12 with 1.75mm pitch the diameter of the blank is
a) 10.25 b) 11.8 c) 11.6 d) 11.4
2) Bench is also known as parallel jaw vice or ____
a) pipe vice b) pin vice c) fitters vice d) hand vice
3) The box nut of bench vice is made of cast iron and phosphorous bronze and ___
a) pig iron b) wrought iron c) gunmetal d) nodular cast iron
4) ___ is the bottom portion of chisel which is ground according to be cut or chipped. a) cutting edge b) hot chisel c) cold chisel d) body or shank 5) Chisel are specified by their ___ of cutting edge
a) shape and length c) width and height
b) length and width d) all of the above
6) A ferrule is fixed on the wooden file handle to avoid ___ when fixing a file
a) cutting b) wastage c) savage d) breakage
7) The teeth of file are cut by ___ with special grinding wheels
a) broaching machine b) milling machines c) file cutting machines d)grinding machines
8) A double fluted drill have ___ cutting edges
a) 3 b) 4 c) 6 d) 2
9) The angle of drill grinding gauge is ___
a) 122deg b) 132deg c) 121deg d) 114deg
10) A reamer with ___ spacing of teeth
a) equal b) parallel c) inclined d) unequal
11) Placing a reamer ___ in the center of hole
a) horizontal b) inclined c) vertical d) all of the above
12) Swage block is made of closed grain ___
a) cast iron c) malleable cast iron
13) A thread of coarse pitch is designated by___
a) M40 b) M30 c) M10 d) M20
14) Lathe lead screw is generally make with acme thread of ___ degree
a) 29 b) 47.5 c) 55 d) 60
b) grey cast iron d) cast steel
15) A screw jack has ___ thread
a) acme b) square c) “V” d) BA thread
16) To maintain the accuracy of a steel rule its ___ and ___ should be protected from damage and rust
a) Edge and surface b) bottom and corner c) all of the above
17) To take accurate measurement it is necessary to read
a) horizontal b) vertical c) parallel d) all of the above
18) ___ are used for supporting circular shafts
a) ‘V’ block b) vices c) ‘C’ Clamps d) Parallel block
19) ___ is put on the surface plate and not on the surface tested to have a clear sight of the job
a) Prussian blue c) cellulose lacquer
b) white wash d) all of the above
20) Parallel clamp is also known as
a) tool makers clamp c) Vice clamp
b) ‘C’ clamp d) none of the above
21) The hardness of cutting edge of chisel should be ___
a) 15 – 69 HRC b) 45 – 55 HRC c) 53-59HRC d) 60-63HRC
22) A file slips on the job when file is used on ___ surfaces
a) soft b) flexible c) hard d) very soft
23) ___ angle of the drill cannot be changed by grinding
a) rake angle b) helix angle c) cutting angle d) clearance angle
24) Reamer drill size is chosen so as to leave the stoke allowance of ___ mm for rough reaming
a) 0.1 - 0.15 b) 0.2 – 0.31 c) 0.3 - 0.4 d) all of the above
25) Reamer drill size is chosen so as to leave the stock allowance for finishing reaming ___
a) 0.05 – 0.02 b) 0.06 – 0.007 c) 0.01 – 0.002 d) none
26) ___ is a hand tool used for closing and locking seams
a) groove b) sleeve c) chisel d) seamier
27) A seam is a joint made by fastening ___ edges of ___ pieces of metallic sheet together 28) ___ is an operation for enlarging previously punched hole
a) 3-3 b) 4-5 c) 2-2 d) 6-6 a) scarping b) drafting c) drifting d) scrolling
29) The air is supplied to the forge by a___
a) blower b) airway c) chipped away d) air conditioner
30) If the major diameter of a metric ‘V’ thread is ___mm
a) 5 b) 10 c) 12 d) 20
31) The lead is the distance a screw thread advances axially in the ____ complete turn
a) 2 b) 3 c) 1 d) 6
32) A pin is a fastener which is found in shape of ____
a) round b) circle c) cylinder d) sphere
33) Taper pins are manufactured with a taper of ___ and used to transmit small torques
a) 1:20 b) 2:10 c) 1:10 d) 1:50
34) The standard measurements are taken at ___ deg C temperature
a) 30 b) 40 c) 20 d) 10
35) ____ Type of length standards in use are
a) 3 b) 2 c) 4 d) 6
36) Its spindle should be kept ____ to the base if possible
a) perpendicular b) parallel c) equal d) all of the above
37) Grip the hammer handle at ___ from its for end while hammering
a) 15 – 30 b) 15 – 40 c) 10 – 20 d) 10 – 30
38) For general purpose the length of hammer handle varies from ___cm
a) 10 -20 b) 15 -30 c)15 – 25 d) 25 – 32.5
39) The hardness for striking faces of hammers should be ____HRC
a) 49 -56 b) 49 -59 c) 50 – 55 d) all of the above
40)
a) grease b) oil c) clean d) none
____ is the slides of vices regularly
41) Use ___ metal clamps to hold finished jobs in the vice
a) universal b) soft c) hard d) all of the above
42) Set spanner ___ pieces
a) 10 b) 13 c) 12 d) 14
43) It is generally used for light duty work
a) socket spanner b) tubular spanner c) pin hook spanner d) adjustable spanner
44) It is generally used for hexagonal bolt or nut is fitted in some less depth
a) tubular spanner b) pin hook spanner c) adjustable spanner d) socket spanner
45) Chisel should be gripped ___mm from the head top
a) 15 – 20 b) 15 – 30 c) 15 – 35 d) 15 – 25
46) Chisel are generally made of high carbon steel having ___% carbon
a) 1 – 1.2 b) 1 – 2 c) 2 – 2.5 d) 2.5 – 5
47) ___ teeth of the blade are not remain in contact with the job
a) 3 – 4 b) 3 – 2 c) 2 – 3 d) 3 – 5
48) Generally a tap set have three taps but B.A tab set have ___ taps
a) 2 b) 5 c) 3 d) 4
49) It is used for hammering while riveting ____
a) ball pein hammer b) straight pin hammer c) cross pin hammer d) none of the above a) lap joint b) spring joint c) butt joint d) riveted joint
50) In this joint the edge of one plate overlaps the edge of the other plate
1) For cutting the thread of M12 with 1.75mm pitch the diameter of the blank is a) 10.25 b) 11.8 c) 11.6 d) 11.4. 2) Bench is also known as parallel jaw vice or ...
10-. 11. MAIN SCALE DIVISIONS. ,o 20. 2 4 6 I 1012141618. ) A. B. c. D. o.o1 ft.fi. o.o2 fr.fi. o.os ft.fr. o.ss ft.fr. - Question PaPer - Page?18. Page 2 of 7 ...
LTlBlClS-2l4lE Booklet Series - D 361227. 8. Shaping of grinding wheel to make it run concentric with the axis is called: - ... in reamers- b) Removing chips. ") Hota in tap wrench d) Hold in machine spindle. Contd....3/- ... contd....4t-. Page 3 of
test 2 rev blank.notebook. 1. February 24, 2015. Feb 233:39 PM. Page 2. test 2 rev blank.notebook. 2. February 24, 2015. Feb 233:41 PM. Page 3. test 2 rev blank.notebook. 3. February 24, 2015. Feb 233:41 PM. Page 4. test 2 rev blank.notebook. 4. Febr
Networks. 4) Digital Forensic. 5)Big Data Analytics. Data Warerhouse and. Mining. Human Machine Interaction Parallel and Distributed Systems. Instrumentation.
The unit of energy in MKS system is? A.Joules. B.Watts. C.Power. D.Force. Ans: C. 72.The sum of two number is 25 and their difference is 13. Find their product?
There was a problem previewing this document. Retrying... Download. Connect more apps... Try one of the apps below to open or edit this item. KODYA ...
There was a problem previewing this document. Retrying... Download. Connect more apps... Try one of the apps below to open or edit this item. STD 8 Sem.1 ...
There was a problem previewing this document. Retrying... Download. Connect more apps... Try one of the apps below to open or edit this item. Main menu.
Whoops! There was a problem loading more pages. Retrying... Whoops! There was a problem previewing this document. Retrying... Download. Connect more apps... Try one of the apps below to open or edit this item. KODYA SOLO(REV)1.pdf. KODYA SOLO(REV)1.p
I think that when you meet the person that you want spend the rest of your life with, you change. A. B. C. D .... a. have run b. have been running c. ran d. am running. 16. â¦â¦.. he and his wife â¦â¦. in their house for a long time? a. Have/live
Last year, a new bridge over the river ______. A. is built. B. was built. C. will be built ...... Nile is considered to be â¦â¦â¦â¦. river in the world. A. longest ...... PRACTICE 21. Ph n I. Khoanh tròn t phát âm khác v i các t còn l i. 1.
Feb 3, 2017 - you should be wise in your own opinion, that blindness in part has happened to Israel until the. fullness of the Gentiles has come in. (26) And so ...
Week 1 Intro and Rev 1 2.3.17.pdf. Week 1 Intro and Rev 1 2.3.17.pdf. Open. Extract. Open with. Sign In. Main menu. Displaying Week 1 Intro and Rev 1 ...
c. Type âtabâ 5 times at the beginning of the paragraph. d. Copy and paste five spaces at the beginning of the paragraph. 4. What might be attached to a USB port on you computer? a. A television set. b. A monitor c. A cable modem. d. A printer. 5
Why do some young people want to find a job after they leave school? a. They are ...... I had a few problems, but Bob gave me some good advices. A B. C. D.
There was a problem previewing this document. Retrying... Download. Connect more apps... Try one of the apps below to open or edit this item. PJOK XI sem 1 ...