1/10 Electric Touring Car Kit Instruction Manual
Powered By:
Introduc on: th
1:10 Touring Car kit is a professional 1:10 4 wheel drive car and should be built by aged 14 years or over or that they had experience building and opera ng R/C model cars before. This is not a toy intended for use by beginners or by children without any supervision of a knowledgeable adult. Please read the instruc on manual carefully before building. Race opt should not be liable for any loss, injury or damages, whether direct, indirect, special, incidental, consequen al, arising from the use, misuse, abuse of this product or accessories required to operate this product.
Warnings: ◎ This product is not intended for those ages under 14 year without any adult supervision. ◎ Assemble this kit only in places away from the reach of children. ◎ Exercise car when using tools and sharp instrument and take care some parts that may have sharp edges when building. ◎ Please do not touch any electronic equipment on the model such as motor and speed controller that having higher temperatures a er the opera on. Otherwise, it may burn yourself seriously by touching them. Be er to allow 10~15 minutes to let any electronic equipment cool down. ◎ Please complete a successful pre-run check of your radio equipment and model before the run. Make sure to keep the wheels of the model off the ground when checking the opera on of the radio equipment. ◎ When on the model, please always turn on the transmi er before turn on the receiver in the car. When off the model, please always turn off the receiver before turn off the transmi er. Otherwise, the model may become uncontrollable and cause serious damage. ◎ Disconnect the ba ery pack before storing your model. ◎ Do not get overcharge for the ba ery or leave ba ery una ended while charging. Never let children charge the ba ery without adult supervision. ◎ Do not operate it on public places, roads or areas where its opera on can conflict with or disrupt pedestrian or vehicular traffic. ◎ Do not use your model as shown below: In places where children and people gather
In rain, wind snow or darkness condi on
In areas where loud noises can disturb others
At any me your line of sight to the model may be obstructed or impaired in any way
1
Electrical Precau ons: ◎ Please do not allow any metal part to short circuit the ba ery or any electronic part using inside the car kit. ◎ Never put ba eries into fire. ◎ Use the recommended charger for the transmi er ba ery and ba ery for electronic speed control. Please follow the charging instruc ons carefully. Please do not over charge the ba ery or choose the wrong charging mode. It becomes dangerous that causes the explosion and lead to the fire. If ba ery becomes extremely hot during the charging, please seek the advice from or get replacement from the corresponding ba ery supplier. ◎ Please unplug charger when not in use. ◎ When not using RC model, please always disconnect and remove the ba ery. ◎ Low ba ery may result in loss of control. Please stop running the car at once when you find its speed start to slow down. ◎ A er use the ba ery, the ba ery remains heat and please recharges it a er the ba ery is cool down. ◎ Never use damaged wires that are dangerous and cause short circuits and may lead to the fire.
Other Equipment Needed (not included): Radio transmi er & receiver
Ba ery for transmi er
Electronic speed control
Steering Servo
540 Type brushes or brushless motor
Pinion Gear (48pitch/64pitch)
190mm body shell
7.4V Nimh or Lipo Ba ery
Touring Car Tire set
Ba ery charger
Tools Needed (not included): 1.5mm, 2.0mm, 2.5mm allen wrench
5.0mm, 5.5mm, 7.0mm hex socket wrench
Modelers cra knife
Turnbuckle wrench
Calipers/Ruler
Camber gauge
Instant glue/Thread lock glue
Shock and Diff Oil
Thrust, Diff and Joint grease
Paint for body shell
Notes: All replacement parts can be found from www.race-opt.com and can be purchased from local hobby shop. If any further informa on needed, please email to
[email protected].
2
125102
125124 121095 125021
125100 122010
125001
125117 125106 128211
017306 017306 017306
125100 125001 125102 125124 125106 125117
ALU. REAR BULKHEAD ALU LOWER SUSP. ADJUST. BULKHEAD ALU. SPUR GEAR SHAFT MOUNT ALU. CHASSIS CENTER MOUNT SUSPENSION MOUNT (FF) SUSPENSION MOUNT SEPARATED HOLDER (FR,RF)
128211 CHASSIS 2.2MM GRAPHITE 121095 COMPOSITE SERVO MOUNT SET 122010 CHASIS BRACE 125021 SERVO MOUNT HOLDER A’’ 017306 HEX SCREW FLAT HEAD M3x6(10)
123003
121065 050212 121065 040050
Tip-1 Tip-1
030510
121065-WH
096116 018304
Tip-2
Tip-2 121065 FIXED PULLEY 20T(2) 123003 ALU SOLID LAYSHAFT 096110 SPUR GEAR 116T/64P 018304 HEX SCREW ROUND HEAD M3x4 030510 BALL-BEARING 5X10X4 040050 E-CLIP 5.0 050212 PIN 2x12
48P
64P
094084
SPUR GEAR 84T/48P
096110
SPUR GEAR 110T/64P
094084-WH
SPUR GEAR 84T/48P
096110-WH
SPUR GEAR 116T/64P
094087
SPUR GEAR 84T/48P
096116
SPUR GEAR 110T/64P
094087-WH
SPUR GEAR 87T/48P
096116-WH
SPUR GEAR 116T/64P
3
043592
090110 60902
045121
031015 121067
017258 090110 123011
050210 050210 121067
128202
163131 031015 018304 125019 121063 090110 121063
PLANETARY GEAR SET-PLASTIC
017258 018304 043592 045121 050210 060902 031015
TIMING BELT PULLEY 38T
121067 COMPOSITE GEAR DIFF. CASE & COVER 125019 FRONT SOLID AXLE 123011 UNIVERSAL CVD DRIVE SHAFT - SPRING STEEL 3.6 S2 163131 128202
FRONT SOLID AXLE SPOOL OUTDRIVE-SPRING STEEL 3.1 S2 DIFF. GASKET
HEX SCREW FLAT HEAD M2.5x8 HEX SCREW ROUND HEAD M3x4 WASHER S 3.5x9x0.2 WASHER S 5x12x0.1 PIN 2x9.8 SILICONE O-RING 9x2
BALL-BEARING 10X15X4
TIPS FOR DIFFERENTIALS Low-Traction
500 cst
High-Traction
1000 cst
+ 1.3g
!
LOCATION
Add 1.3g of oil the diff.
050210
050312 162147
122146 121099 122127 160247 122006 122006 CVD JOINT PIECE 122127 CVD AXLE SHAFT-SLANTING 122146 UNIVERSAL CVD DRIVE SHAFT-SPRING STEEL 46MM 2.0PIN-S2 121099 DRIVE SHAFT REPLACEMENT PLASTIC CAP 162147 UNIVERSAL CVD DRIVE SHAFT-SPRING STEEL 47MM 3.0PIN-S2
4
050210 050312 122127 160247
PIN 2x9.8 PIN 3x12 CVD AXLE SHAFT-STRAIGHT CVD DRIVE SHAFT SPRING STEEL-47mm 3.0PIN
124247 124239 124430
124431
124432
124433
060615
Tip-1
124211
124402 124433
Tip-1
125029 124003 129455
124012
Tip-2 124201
121058
040025
061401 121058 124239 124402 124201 124003 124318 124433 124211
SHOCK BALL JOINT HARDENED SHOCK SHAFT 3.0*39mm RAS-SHOCK TOP COVER RAS- SHOCK CAP SUSPENSION SPRING RETAINER-12MM SHOCK TUBE-HARD COATED 18MM COMPOSITE PISTONS 3-HOLE RAS-SHOCK CAP BALL END 5.9MM
124012 125029 124403 129455 040025 061401 060615
124322 124318
124403
Tip-2
060615
Springs
129450
1.4*21*5.0 SUSPENSION SPRING RD 3.5KG
129455
1.4*21*5.5 SUSPENSION SPRING SR 3.0KG
129460
1.4*21*6.0 SUSPENSION SPRING YE 2.5KG
ALU SHOCK SPRING RETAINING COLLAR 129465 ALU SHOCK BOTTOM CAP RAS-SHOCK BOTTOM COVER 1.4*21*5.5 SUSPENSION SPRING SR 3.0KG E-CILP 2.5 SILICONE O-RING 14x1 SILICONE O-RING 6*1.5
1.4*21*6.5SUSPENSION SPRING BL 2.0KG
TIPS FOR SHOCK ABSORBER 1
3
2 90°
4
030510 1.5mm
127251 127151 123114
127218 127118
121096
018308 040362
017306 125023
018310 017312
123114 121096 127118 127151
BULKHEAD MOUNT POST COMPOSITE ADJUSTMENT BALL-BEARING HUB SYNCHRONOUS BELT SHORT-189 63T SYNCHRONOUS BELT LENGTH-513 171T
125023 030510 040362
OPTIONAL MOTOR MOUNT BALL-BEARING 5x10x4 ALU WASHER 3x6x2
5
018308 017306 017312 018310
HEX SCREW ROUND HEAD M3x08 HEX SCREW FLAT HEAD M3x6 HEX SCREW FLAT HEAD M3x12 HEX SCREW ROUND HEAD M3x10
018308
123126
018308
018308 018310 018306 018306
128212
040361
123113 125125 040361
128214
125004
128213 017306 018306
018308
128115 125022
125004 128212 128213 128214 128115 125022 123113
040361 ALU WASHER 3x6x1 123126 ANTI-TWIST BAR 2.6MM 125125 ANTI-TWIST BAR HOLDER 018306 HEX SCREW ROUND HEAD M3x6 018308 HEX SCREW ROUND HEAD M3x8 018310 HEX SCREW ROUND HEAD M3x10 017306 HEX SCREW FLAT HEAD M3x6
BEARING SLEEVE CLAMP -GT CAR(L+R) SHOCK TOWER (REAR) 3.0MM GRAPHITE SHOCK TOWER (FRONT) 3.0MM GRAPHITE UPPER DECK GRAPHITE GRAPHITE FLOATING SERVO MOUNT PLATE SERVO MOUNT HOLDER B’’ TWIST BAR HOLDER SCREW
125109 017310
015408
050350 015408
040361
121175(3")
017310
125117 121061
121175(0")
040361 050347 121062 Front
050347 FRONT ARM PIVOT PIN 3*47(2) 050350 REAR ARM PIVOT PIN 3*50(2) 121061 REAR SUSPENSION ARM 121062 FRONT SUSPENSION ARM 121175(0") SUSPENSION MOUNT INSERT 0° 121175(3") SUSPENSION MOUNT INSERT 3°
47mm
Rear
50mm
040361 ALU WASHER 3x6x1 125117 SUSPENSION MOUNT SEPARATED HOLDER (FR,RF) 125109 SUSPENSION MOUNT HOLDER (RR) 015408 HEX SET SCREW M4x8 017310 HEX SCREW FLAT HEAD M3x10
6
020332 018314
018316 121032
122025
015304
018314 018312 121049 018308
031015 121031
024900 123001
040364
030612
121044
122023
015304 121049 COMPOSITE BALL JOINT 4.9MM - OPEN 020332 ADJ. TURNBUCKLE L/R 32 MM - SPRING STEEL 024900 PIVOT BALL 4.9 MM DOUBLE BEVEL SHOULDERS 121031 COMPOSITE STEERING BLOCK 121032 COMPOSITE UPRIGHT REAR 121044 COMPOSITE C-HUB FRONT BLOCK 4° DEG 122023 FRONT PIVOT PIN FOR C-HUB 3*23 122025 REAR PIVOT PIN FOR UPRIGHT 3*25 123001 STEEL STEERING BUSHING
018308 018312 018314 018316 030612 040364 015304 031015
HEX SCREW ROUND HEAD M3x8 HEX SCREW ROUND HEAD M3x12 HEX SCREW ROUND HEAD M3x14 HEX SCREW ROUND HEAD M3x16 BALL-BEARING 6x12x4 ALU WASHER 3x6x4 HEX SET SCREW M3x4 BALL-BEARING 10X15X4
TIPS FOR PRE ASSEMBLED Front Rear
121249
020322
54mm 59.5mm
024906 121081
024906 018304
Tip-1 040361
120051
030508
030306
024900
120051
040362
125014
121049
Tip-1 020336
Servo Arm
121081 Servo Arm-J (JR,KO)
018308
121081 Servo Arm-F (Futaba)
017312 123002
121249 COMPOSITE BALL JOINT 4.9MM - CLOSED WITH HOLE 020322 ADJ. TURNBUCKLE L/R 20 MM - SPRING STEEL 020336 ADJ. TURNBUCKLE L/R 36 MM - SPRING STEEL 024906 BALL END 4.9MM WITH THREAD 6MM H2.0 024900 PIVOT BALL 4.9 MM DOUBLE BEVEL SHOULDERS 121049 COMPOSITE BALL JOINT 4.9MM-OPEN 120051 ALU STEERING BELL CRANK (L+R) 121081 COMPOSITE SERVO HORN 125014 ALU STEERING PLATE
123002 ALU STEERING POST 018304 HEX SCREW ROUND HEAD M3x4 018308 HEX SCREW ROUND HEAD M3x8 017312 HEX SCREW FLAT HEAD M3x12 030306 BALL-BEARING 3X6X2.5 030508 BALL-BEARING 5X8X2.5 040361 ALU WASHER 3x6x1 040362 ALU WASHER 3x6x2
7
TIPS FOR STEERING
45mm
63.5mm
017312
123112 017308
123112 ALU WASHER 017308 HEX SCREW FLAT HEAD M3x8
017312
015325
Tip-1 Front Anti-Roll Bars 129114 129116 129118
Front Front Front
HEX SCREW FLAT HEAD M3x12
024901
1.4mm 1.6mm 1.8mm
129212
Tip-2
017310 015304
Tip-2
121074
129212 129214
129114
129216
Tip-1 121074
129218
121149
015304 015325 017310 024901
121074 COMPSITE ANTI-ROLL BAR HOLDERS 121149 BALL JOINT 5 MM - SHORT OPEN (4) 129114 ANTI-ROLL BAR FRONT 1.4MM 129212 ANTI-ROLL BAR REAR 1.2MM
8
Rear Anti-Roll Bars Rear Rear Rear Rear
HEX SET SCREW M3x4 HEX SET SCREW M3x2,5. HEX SCREW FLAT HEAD M3x10 4.9 MM TRIPPING BALL HEAD - STEEL (4)
1.2mm 1.4mm 1.6mm 1.8mm
TIPS FOR STEERING
015310
121149
015310 121149
HEX SET SCREW M3x10 BALL JOINT 5MM-SHORT OPEN
3mm
124501
019301 124257 124249
040362
015310
INITIAL POSITION
025801 5mm
025801 015310 019301
BALL UNIVERSAL 5.8 MM HEX H3.0 HEX SET SCREW M3x10 NUT M3 WITH SERRATED FLANGE
124501 RAS-SHOCK HOLDER TOOL 124249 ALU SHOCK ABSORBER-SET 18mm 12x49mm 040362 ALU WASHER 3x6x2
018210 121023 017310 121012 121022
018308 128201
019300
121021 121011 121011
017310 121011 121012 121021 121022 121023
COMPOSITE BUMPER COMPOSITE UPPER HOLDER FOR BUMPER FRONT BODY MOUNT SET REAR BODY MOUNT SET BODY SUPPORT
128201 017310 018210 018308 019300
9
FOAM BUMPER HEX SCREW FLAT HEAD M3x10 HEX SCREW ROUND HEAD M2x10 HEX SCREW ROUND HEAD M3x8 NUT M3
018310
017308 125126
123116
128216
125126 123116 128216
ALU.BATTERY HOLDER MOUNT 017308 018310
BATTERY MOUNT HOLDER SHAFT 2X24MM GRAPHITEBATTERY HOLDER
HEX SCREW FLAT HEAD M3x8 HEX SCREW ROUND HEAD M3x10
050210 016205 125012
127661 127662 127663
019401
125012 OPTION ALU WHEEL HUB 019401 NUT M4 WITH SERRATED FLANGE 127661 SLICK TYRE SET
050210 PIN 2x9.8 (10) 016205 HEX SOCKET CAP SCREWS M2.5x5
10
1/10ELECTRICTOURINGCAR 120146
122127
122146
46MM CVD DRIVE SHAFT SPRING STEEL
160247
46MM -2MM PIN
CVD AXLE SHAFT-STRAIGHT
UNIVERSAL CVD DRIVE SHAFT SPRING STEEL
162147
47MM CVD DRIVE SHAFT SPRING STEEL
122023
050347
UNIVERSAL CVD DRIVE SHAFT SPRING STEEL
ADJ. TURNBUCKLE L/R 32MM -SPRING STEEL
123002
050350
FRONT ARM PIVOT PIN3*47
REAR ARM PIVOT PIN 3*50
122098
020336
REAR PIVOT PIN FOR UPRIGHT3*25
020322
020332
CVD JOINT PIECE
47MM -3MM PIN
122025
FRONT PIVOT PIN FOR C-HUB3*23
122006
DIFF CROSS SHAFT
122010
ADJ. TURNBUCKLE L/R 20MM-SPRING STEEL
123001
CHASIS BRACE
STEEL STEERING BUSHING
123011
123204
123003
ADJ. TURNBUCKLE L/R 36MM-SPRING STEEL
3.6 S2
3.1 S2 ALU STEERING POST
ALU SOLID LAYSHAFT
UNIVERSAL CVD DRIVE SHAFT-STEEL
160131
163131
3.1 S2 FRONT SOLID AXLE SPOOL OUTDRIVE-SPRING STEEL
UNIVERSAL CVD DRIVE SHAFT-STEEL
124003
125019
3.1 S2
12mm FRONT SOLID AXLE
FRONT SOLID AXLE SET-SPRING STEEL
11
21
ALU. SUSPENSION SPRING RETAINER
1/10ELECTRICTOURINGCAR 124012
129550
129555
4.5KG ALU SHOCK SPRING RETAINING COLLAR
129565
4.0KG
1.5*21*5.0 SUSPENSION SPRING RD
1.5*21*5.5 SUSPENSION SPRING GN
129450
3.0KG 1.5*21*6.5SUSPENSION SPRING BL
129465
129560
129455
3.5KG
3.5KG 1.5*21*6.0 SUSPENSION SPRING YE
129460
3.0KG
1.4*21*5.0 SUSPENSION SPRING RD
1.4*21*5.5 SUSPENSION SPRING SR
040060
2.5KG 1.4*21*6.0 SUSPENSION SPRING YE
129114
129116
ANTI-ROLL BAR FRONT 1.4MM
ANTI-ROLL BAR FRONT 1.6MM
2.0KG 1.4*21*6.5SUSPENSION SPRING BL
BODY CLIP 6MM
129118
129212
ANTI-ROLL BAR FRONT 1.8MM
ANTI-ROLL BAR REAR 1.2MM
ANTI-ROLL BAR REAR 1.4MM
024900
024901
129218
ANTI-ROLL BAR REAR 1.8MM
024904
BALL END 4.9MM WITH THREAD 4MM
129214
4.9MMTRIPPING BALL HEAD-STEEL
PIVOT BALL 4.9MM DOUBLE BELVE SHOULDERS
024906
BALL END 4.9MM WITH THREAD 6MM
ANTI-ROLL BAR REAR 1.6MM
024902
TRIPPING BALL HEAD-4.9MM ALU.
024908
024910
BALL END 4.9MM WITH THREAD 8MM
BALL END 4.9MM WITH THREAD 10MM
12
22
129216
1/10ELECTRICTOURINGCAR 025800
BALL UNIVERSAL 5.8MM HEX
BALL UNIVERSAL 5.8MM HEX
125001
125004
ALU LOWER SUSP. ADJUST. BULKHEAD
BEARING SLEEVE CLAMP -GT CAR -(L+R)
125317
30MM FAN MOUNT 090111
PLANETARY GEAR SET-HARD COATED
061401
SILICONE O-RING 14X1
025806
025801
025808
BALL END 5.8MM WITH THREAD 6MM
125012
OPTION ALU WHEEL HUB
125418
40MM FAN MOUNT
ALU STEERING PLATE
125023
ALU STEERING BELL CRANK (L+R)
OPTIONAL MOTOR MOUNT
060902
ALU SHOCK BOTTOM CAP
PLANETARY GEAR SET - PLASTIC
060615
125014
120051
125029
090110
BALL END 5.8MM WITH THREAD 8MM
128202
SILICONE O-RING 6X1.5
SILICONE O-RING 9X2
128201
DIFF GASKEL
FOAM BUMPER
127118
127151
127218
127251
SYNCHRONOUS BELT SHORT-FIBRE-189 63T
SYNCHRONOUS BENT LONG -FIBRE-513 171T
SYNCHRONOUS BELT SHORT-PU KEVLAR-189 63T
SYNCHRONOUS BELT LONG-PU KEVLAR-513 171T
13
23
1/10ELECTRICTOURINGCAR 125100
128117
GRAPHITE STEERING PLATE
125125
ALU. REAR BULKHEAD
ALU. SPUR GEAR SHAFT MOUNT
123124
125126
ANTI-TWIST BAR HOLDER
123128
123113
ANTI-TWIST BAR 2.6MM
123114
TWIST BAR HOLDER SCREW
ALU WASHER
ALU. CHASSIS CENTER MOUNT
123126
ANTI-TWIST BAR 2.4MM
ALU.BATTERY HOLDER MOUNT
123112
ANTI-TWIST BAR 2.8MM
125124
125102
BULKHEAD MOUNT POST
123116
125106
125109
125117
BATTERY MOUNT HOLDER SHAFT 2X24MM
SUSPENSION MOUNT (FF)
SUSPENSION MOUNT HOLDER (RR)
SUSPENSION MOUNT SEPARATED HOLDER (FR,RF)
128211
128214
128213
128212
GRAPHITE CHASSIS 2.2MM GRAPHITE
128009
GRAPHITE
GRAPHITE UPPER DECK GRAPHITE
128109
GRAPHITE
SHOCK TOWER (FRONT) 3.0MM GRAPHITE
SHOCK TOWER(REAR)3.0MM GRAPHITE
128209
128216
GRAPHITE 2.0
GRAPHITE 2.5
GRAPHITE 3.0
GRAPHITE
ANTI-TWIST REAR UPPER DECK 2.0MM GRAPHITE
ANTI-TWIST REAR UPPER DECK 2.5MM GRAPHITE
ANTI-TWIST REAR UPPER DECK 3.0MM GRAPHITE
GRAPHITE BATTERY HOLDER
14
24
1/10ELECTRICTOURINGCAR 124249
121201 124201
124257
12mm*49mm
12mm*57mm
REDUCED AIR SHOCKER (49MM)
REDUCED AIR SHOCKER (57MM)
124247
124318
RAS-SHOCK SHAFT 3X47MM
124430
RAS-SHOCK PISTON (WITHOUT HOLE)
124402
RAS-SHOCK TOP COVER
124239
RAS- SHOCK CAP
124322
124403
12mm*18mm
12mm*22mm
RAS-SHOCK BODY 12X18MM
RAS-SHOCK BODY 12X22MM
124431
124432
RAS-SHOCK PISTON (1 HOLE)
RAS-SHOCK PISTON (2 HOLE)
124211
124501
RAS-SHOCK HOLDER TOOL
RAS-SHOCK CAP BALL END 5.9MM
121175
128115
SUSPENSION MOUNT INSERT
GRAPHITEFLOATINGSERVOMOUNT PLATE
RAS-SHOCK SHAFT 3X39MM
120200
RAS-SHOCK BOTTOM COVER 124433
RAS-SHOCK PISTON (3 HOLE)
061301
RAS-SHOCK UPPER O-RING (13X1MM)
121011
Carbon Fiber
121012
COMPOSITE UPPER HOLDER FOR BUMPER
121021
OPTIONAL FLOATING SERVO MOUNT
121022
FRONT BODY MOUNT SET
REAR BODY MOUNT SET
15
25
COMPOSITE BUMPER
121023
BODY SUPPORT
1/10ELECTRICTOURINGCAR 161024
121032
121031
121042
71MM LENGHT
REAR BODY MOUNT SET
121044
COMPOSITE C-HUB FRONT BLOCK 4DEG
121065-WH
FIXED PULLEY 20T (POM)
121067
COMPOSITE GEAR DIFF. CASE & COVER
121049
COMPOSITE BALL JOINT 4.9MM OPEN
121099
DRIVE SHAFT REPLACEMENT PLASTIC CAP
COMPOSITE UPRIGHT REAR
COMPOSITE STEERING BLOCK
121061
121062
REAR SUSPENSION ARM
FRONT SUSPENSION ARM
121065
121068-WH
FIXED PULLEY 18T (POM)
FIXED PULLEY 20T(2)
121096
121074
COMPOSITE ANTI-ROLL BAR HOLDERS
COMPOSITEADJUSTMNET BALL-BEARING HUB
121149
121058
BALL JOINT 5MM-SHORT OPEN
SHOCK BALL JOINT
094084
094084-WH
SPUR GEAR 84T/48P POM
SPUR GEAR 84T/48P
16
26
COMPOSITE C-HUB FRONT BLOCK 2DEG
121063
TIMING BELT PULLEY 38T
121068
FIXED PULLEY 18T
121081
COMPOSITE SERVO HORN
121249
COMPOSITE BALL JOINT 4.9MM- CLOSEDWITH HOLE
094087
SPUR GEAR 87T/48P
1/10ELECTRICTOURINGCAR 094087-WH
096110
SPUR GEAR 87T/48P POM
SPUR GEAR 110T/64P
127661
096116-WH
SPUR GEAR 116T/64P POM
SPUR GEAR 110T/64P POM
THREADED TYRE SET
SLICK TYRE SET
161112
3.1 DRIFT TYRE-200mm
GEAR DIFFERENTIAL - SET
030306
121113
SPUR GEAR 116T/64P
127663
127662
161113
147661
096116
096110-WH
SLICK TYRE SET
121114
3.6
METAL GEAR 3.1 OPTIONAL GEAR DIFFERENTIAL - SET
030508
GEAR DIFFERENTIAL - SET
030510
METAL GEAR 3.6 OPTIONAL GEAR DIFFERENTIAL - SET
030612
BALL-BEARING 6X12X4
019401
NUT M4 WITHSERRATED FLANGE
BALL-BEARING 3X6X2.5
031015
BALL-BEARING 10X15X4
091402
BALL-BEARING 5X8X2.5
019301
BALL-BEARING 5X10X4
019300
NUT M3 WITH SERRATED FLANGE
050209
HEX SET SCREW M3X2.5
PIN 2X9.0
27 17
NUT M3
050210
PIN 2X9.8
1/10ELECTRICTOURINGCAR 050312
050212
040373
PIN 3X12
PIN 2X12
WASHER S 3X7X0.3
WASHER S 3.5X9X0.2
040362
ALU WASHER 3X6X3
040365
ALU WASHER 3X6X5
ALU WASHER 3X6X4
019505
019503
2g WHOLE VEHICLE BEARING
ALU WASHER 3X6X1.5
040364
019502
030102
040366
ALU WASHER 3X6X1
040363
ALU WASHER 3X6X2
WASHER 5X12X0.1
040361
WASHER 5X12X0.3
WASHER 5X12X0.2
045121
WASHER 3.5X9X0.4
WASHER 3.5X9X0.3
045123
045122
WASHER S 3X7X0.5
043594
043593
043592
040375
5g
3g
ROUND SHAPE BALANCE WEIGHT
ROUND SHAPE BALANCE WEIGHT
019510
ROUND SHAPE BALANCE WEIGHT
016205
10g HEX SOCKET CAP SCREWS M2X5
ROUND SHAPE BALANCE WEIGHT
28 18
1/10ELECTRICTOURINGCAR 015325 015304 015306 015310 015312 015314 015404 015405 015406 015408 015410 015412
M3X2.5 M3X4 M3X6 M3X10 M3X12 M3X14 M4X4 M4X5 M4X6 M4X8 M4X10 M4X12
017258 017306 017308 017310 017312 017314 017316
HEX SCREW FLAT HEAD
HEX SET SCREW 018210 018256 018304 018305 018306 018308 018310 018312 018314 018316
M2.5X8 M3X6 M3X8 M3X10 M3X12 M3X14 M3X16
M2X10 M2.5X6 M3X4 M3X5 M3X6 M3X8 M3X10 M3X12 M3X14 M3X16
040025 040030 040040 040050
C2.5 C3.0 C4.0 C5.0
E-CLIP
HEX SCREW ROUND HEAD
094018 094019 094020 094021 094022 094023 094024 094025 094026 094027 094028 094029 094030
096024 096025 096026 096027 096028 096029 096030 096031 096032 096033 096034 096035 096036 096037 096038
18T 19T 20T 21T 22T 23T 24T 25T 26T 27T 28T 29T 30T
24T 25T 26T 27T 28T 29T 30T 31T 32T 33T 34T 35T 36T 37T 38T
096039 096040 096041 096042 096043 096044 096045
39T 40T 41T 42T 43T 44T 45T
PINON GEAR ALU HARD COATED(64P)
PINON GEAR ALU HARD COATED(48P)
19
29
