1. Write Technical notes on the following. (a) Back-to-Back HVDC coupling system. (b) Back to back DC link along with AC feeder.
.in
IV B.Tech I Semester Supplementary Examinations, November 2005 HVDC TRANSMISSION (Electrical & Electronic Engineering) Time: 3 hours Max Marks: 80 Answer any FIVE Questions All Questions carry equal marks ????? [8+8=16]
or ld
2. Clearly explain the different converter configurations commonly employed for HVDC converter and bring out their relative merits and demerits. [16] 3. What are the limitations of manual control of HVDC converters? Explain the basic means of achieving control of converters? [16] 4. What is meant by reactive power control? Explain in detail has it is achieved. [16] 5. Obtain the mathematical model of a d.c. network and d.c. converter, including converter controller. [16] 6. (a) What are the basic principles of over current protection.
uW
(b) Discuss the various faults exist in converter station? Explain.
[8] [8]
7. It is required to eliminate harmonics of order 10 and below 10 other than fundamental in a 12 pulse converter. Suggest a suitable transformer configuration and derive an equation for primary current of transformer. [16]
?????
Aj
nt
8. What are the various types of filters that are employed in HVDC converter station? Discuss them in detail. [16]
NR410205 IV B.Tech I Semester Supplementary Examinations ...
(b) Back to back DC link along with AC feeder. 2. Clearly explain the different converter configurations commonly employed for HVDC · converter and bring out ...
NR. IV B.Tech I Semester Supplementary Examinations, November 2005 ... NR size is smaller than the fiber core, and the small gap between the source and.
RELIABILITY & SAFETY ENGINEERING · (Electronics & Control Engineering) ... (a) Explain the following terms in connection with reliability evaluation. [2+3].
NR. IV B.Tech I Semester Supplementary Examinations, November 2005 ... 3. Analyse the following frame using stiffness method. EI constant. (figure 3) [16].
What do you understand by Non-destructive testing techniques? List various tech- · nique of NDT and explain any three of them · [16]. 8. Write short notes on the ...
Using dynamic programming method, how do you find the most economical ... the additional reactive power requirement at the receiving end to meet a load of ...
(b) Explain the architecture of Honeywell 60/66 multiprocessor system. [8+8] · 6. (a) Define the term nonpreemptive scheduling. With an example illustrate the.
5. (a) Compare and contrast adaptive and fuzzy control techniques used in motion- ... Discuss various application of microprocessor control programmable logic ...
... No: NR410805. NR. IV B.Tech I Semester Supplementary Examinations, November 2005 ... ideal, Raoult's and Dalton's laws are applicable. [16] · *****. 2 of 2.
(c) Discuss the panel method for compressible subsonic and supersonic flows [6] · 6. (a) Derive a descretized form of generic integral form of continuity and ...
7. Distinguish between the power transmission by chains, ropes and wire ropes in · hoisting equipment. [16] · 8. Sketch and explain a hydraulic jack. [16] · *****.
(b) Clearly explain the use of category analysis in Trip generation models. [6] · 5. Explain the concept of Trip distribution. Disucss about the various growth factor.
DISTRIBUTED COMPUTER CONTROL SYSTEMS · (Electronics & Control ... (b) Explain the design techniques in real time systems. [8+8] · 5. Explain in detail ...
[8+8] · 2. Explain the mathematical interpretation of finite element method for ... (a) Show that the value of the shape function N1 of node i and node k of a simplex.
IV B.Tech I Semester Supplementary Examinations, November 2005. INTERNET & JAVA PROGRAMMING · (Electronics & Computer Engineering) · Time: 3 hours · Max Marks: 80 · Answer any FIVE Questions · All Questions carry equal marks · ***** · 1. (a) Defferet
(a) Power control of HVDC converters · (b) Starting and ... (b) Draw the flow chart for AC/DC load flow. ... (b) Discuss the various faults exist in converter station?
(a) What is Redundancy? Explain the different types of Redundancy operation with LCU. (b) explain the operation of: i. Operator interface. ii. Engineer interface.
chimney attached to the boiler? Explain how will you estimate its concentration · in this flue gas? 5. Describe the removal of sulphurdioxide by dry process using ...
Explain determinants and use of determinancy diagram. 2.a) ... Draw the E/R model representation of many-to-many relationship and · superfluous entity tables.
(b) Briefly explain the shift instructions also give the examples. 4. Write a procedure SOLUTION that will use the arithmetic operators procedures to evaluate the ...
b) Give the steps of a registry-based algorithm for finding and using idle · workstations. 4.a) With reference to distributed file system implementation explain i) ...
let us make a rough estimate of its role. For this assume isothermal operations in a 2.5-cm ID tubular reactor, using a Reynolds number of 10 000 for flowing fluid. The cracking reaction is approximately first order. If calculations show that 99% dec
Explain the Remote procedure call in detail. 3. Explain distributed Deadlock Detection and prevention methods. 4. Explain the following processor Allocation ...