Contents What you will need ..................................................................................................... 3 Removing the damaged print tip ................................................................................ 4 Installing the new print tip........................................................................................... 6 Levelling the print tips for CubeX Duo/Trio................................................................. 7 Setting Print Tip offsets .............................................................................................. 8 Fastening the print tip on a CubeX............................................................................. 9
2
What you will need Print tip assembly
2.5mm Hex driver
Pliers
3
Before beginning this process please remove all filament from the print jets and check that your print pad is level. For instructions on how to do this please refer to the CubeX users guide
Removing the damaged print tip Turn off the CubeX and Unplug it from the mains power. Unplug the print tip from the Print jet sensor board and feed the wire down the hole to the print tip.
4
Unfasten the print tip holding bolt.
The print tip and print jet are assembled by sliding the print tip into the print jet and twisting it (as pictured).
To remove the print jet you will need to twist it and pull down, eventually you will find the correct orientation and the print tip should easily slide out.
5
Installing the new print tip Feed the print tip wires up through the print jet carriage and plug them into the Print Jet sensor board.
Slide the new print tip into the print jet and turn it until the print tip wires are orientated to travel straight up to the Print Jet sensor board.
6
Levelling the print tips for CubeX Duo/Trio If your CubeX only has a single print jet please see section ‘Fastening the print tip on a CubeX’ 1. Power on the CubeX printer 2. To clean the nozzles for levelling, put the CubeX printer into PJ-Control mode. Heat all of the print jets EXCEPT for the new one to 230° and clean of any plastic debris with pliers. Allow the Print Jets to cool down.
3. Put the CubeX printer into manual move mode.
4. Raise the print pad until it is approximately 5mm away from the print tips.
7
5. Slowly raise the print pad until it lifts the new print tip in line with the others. All three print tips should be touching the bed without putting any pressure on it.
6. Turn the CubeX printer off and unplug it from the mains power supply.
7. Using the 2.5mm hex driver, tighten the print tip holding bolt (pictured) to lock the print tip in place.
With the print tips levelled you can now turn on the CubeX printer and set the print tip offsets
Setting Print Tip offsets See the CubeX user guide for instructions on how to set your print tip offsets.
8
Fastening the print tip on a CubeX A CubeX with a single print jet does not have a second or third nozzle to reference the print tip level. Instead you have to use the CubeX wiping stick. 1. Power on the CubeX printer 2. Put the CubeX into manual move.
3. Raise the print pad until it is approximately 5mm away from the print tip.
4. Slowly raise the print pad until the print tip is touching it.
5. Continue raising the print pad until there is approximately 0.5mm between the print pad and the CubeX wiping stick.
9
6. Turn the CubeX printer off and unplug it from the mains power supply. 7. Using the 2.5mm hex driver, tighten the print tip holding bolt (pictured) to lock the print jet in place.
With the print tip fastened you can now turn on the CubeX printer and start printing.
three print tips should be touching the bed without putting any pressure on it. 6. Turn the CubeX printer off and unplug it from the mains power supply. 7. Using the 2.5mm hex driver, tighten the print tip holding bolt (pictured) to lock the print tip in place. With the print tips levelled you can now turn on the CubeX printer and set ...
Unfasten the print tip holding bolt. The print tip and print jet are assembled by sliding the print tip into the print jet and twisting it (as pictured). To remove the print jet you will need to twist it and pull down, eventually you will find the co
the print tip level. Instead you have to use the CubeX wiping stick. 1. Power on the CubeX printer. 2. Put the CubeX into manual move. 3. Raise the print pad until ...
15. Tightening the X belt. Use an M5 spanner to turn the loose X belt fastener until there is tension on the belt. Use the 3mm hex driver to fasten the X belt.
8 Mar 2006 - from the object B] Object-oriented programming is per formed by displaying objects connected by wirings that rep resent the ?ow of data, control or messages from one object to a second object. A coupling ofinput and output terminal so th
to act like, to call yourself. Long words administratively ... objects with the one in the center highlighted. Staying with the ... Center at www.uscis.gov/citizenship.
indicating their experience with similar engagements. In addition, any relevant. Continuing Education Programs should be listed. 9.1.5.1 Substitutions for the ...
and responsibilities, future career and educational goals, self-management of behavior and substance use, and development and ... See how many of the TIP guidelines you can identify being applied in this work with Kendra. ... community college progra
explanation. Tip #5: Think analytically. Find more information ... For example, the reading test may ask students to answer questions like these about a text/topic:.
explanation. Tip #5: Think analytically. Find more information ... For example, the reading test may ask students to answer questions like these about a text/topic:.
Can. you rewrite this sentence? Can you provide specific details to show what you. mean here? o Instead of confusing, try: I'm not sure I know what your ...
How long will the procedure last and will I be under anesthesia? 4. Will I have dressings, bandages, or stitches after surgery? When should they be removed? 5.
ernment regulatory agencies could not make spectrum allocations in proportion ... cept is a system level idea which calls for replacing a single, high power trans-.
Removing the Jet Wipe. Run the bed to the bottom of the machine using manual move. Lift Jet wipe out of the machine. Removing the Case and floor panel.
Dui'ingrhe course discussions held on 0710512015 in the Chamberof ED/E(N) on NFIR's. pNM item No.l412015, the Official Side requested the Federation to provide details of specific. cases for taking necessary action to rectify the situation. ' ln this
Before beginning this process please ensure that all cartridges have been removed from the machine. Removing the Jet Wipe. Run the bed to the bottom of the machine using manual move. Lift Jet wipe out of the machine. Removing the Case and floor panel
Whoops! There was a problem loading more pages. Retrying... Kurzweil Tip Sheet.pdf. Kurzweil Tip Sheet.pdf. Open. Extract. Open with. Sign In. Main menu.
In the GO read above orders have been issued to the effect that all Government employees and teachers who attain the age of 55 years during the course of the ...
This solution is ... Dr. Leslie J. Couse, EC-SEAT Project Director- [email protected]; 603-862-0638. Website: ... AT & EC Tip Sheet_July2014.pdf. AT & EC ...