Contents What you will need .................................................................................................... 3 Removing the Case. ................................................................................................. 5 Removing the old X belt ............................................................................................ 6 Removing the X motor .............................................................................................. 7 Installing the new X belt ............................................................................................ 9 Attaching the new X motor ...................................................................................... 12 Tightening the X belt ............................................................................................... 15 Checking the belt tension ........................................................................................ 16 Re attaching the case. ............................................................................................ 17
2
What you will need Replacement X axis motor and belt
3mm Hex Driver
2.5mm Hex Driver
3
Pliers
M5 Spanner
4
Before beginning this process please ensure that the print pad is lowered to the bottom of the machine and all cartridges have been removed. Unplug the CubeX from mains power.
Removing the Case. Using the 3mm hex driver remove the 8 case bolts (4 either side of the machine).
Unplug the CubeX screen.
Lift the case up off the CubeX.
5
Removing the old X belt Use the 3mm hex driver to remove the X belt fastening bolts to free the X belt from the Print Jet carriage.
Using the 2.5mm driver remove the X belt fasteners from each end of the belt.
Gently pull the X belt from the machine.
6
Removing the X motor Unplug the motor wire
Unfasten the motor mount bolts using the 2.5mm hex driver and remove the assembly from the machine (this will result in an unfastened Y belt).
7
Remove all fastenings and keep safe as these will be required again later in the manual.
8
Installing the new X belt Attach one of the X belt fasteners to the machine. Note the orientation pictured; The grub screw biting into the teeth of the belt, the length of the belt leaving the right hand side of the fastening with the hex side of the fastening facing up.
Loop the belt around the fastening.
Attach the fastening hex side up to the left hand side of the Print Jet carriage.
9
Thread the belt under the Print Jet carriage
Thread the belt around the X idler bearing
Attach the second belt fastening again noting the orientation; The grub screw biting into the teeth of the belt, The length of the belt leaving the left hand side of the fastening with the circular side of the fastening facing up.
10
Attach to the right hand side of the Print Jet carriage but do not fully fasten.
Place the belt in position to pass around the X motor
11
Attaching the new X motor Attach the X motor mount to the X motor noting the orientation pictured.
Place one of each of the leftover bolts through the Y belt clamps.
Place the Y belt clamps either side of the X motor mount with the longer bolts at the back of the mount as pictured.
12
Place the spacers into the block as pictured.
Place the X motor assembly onto the block and fasten loosely ensuring that the X belt travels around the X motor pulley.
13
Fasten one side of the Y belt by placing it between the Y belt clamps and fastening the two bolts. Apply equal pressure to each bolt to ensure the X motor mount stays flat.
Pull the unfastened side of the Y belt through its corresponding clamp, pull it taught with pliers and fasten the two bolts, again applying equal pressure to each bolt to ensure the X motor mount stays flat.
Plug the X motor wire into the X motor
14
Tightening the X belt Use an M5 spanner to turn the loose X belt fastener until there is tension on the belt.
Use the 3mm hex driver to fasten the X belt.
15
Checking the belt tension Move the Print Jet carriage to the back left hand corner of the machine.
The belts should have some tension on them but you should be able to comfortably touch the belts together (as pictured) when the machine is in this position.
16
Re attaching the case. Slide the case onto the CubeX and plug in the CubeX screen.
15. Tightening the X belt. Use an M5 spanner to turn the loose X belt fastener until there is tension on the belt. Use the 3mm hex driver to fasten the X belt.
the print tip level. Instead you have to use the CubeX wiping stick. 1. Power on the CubeX printer. 2. Put the CubeX into manual move. 3. Raise the print pad until ...
three print tips should be touching the bed without putting any pressure on it. 6. Turn the CubeX printer off and unplug it from the mains power supply. 7. Using the 2.5mm hex driver, tighten the print tip holding bolt (pictured) to lock the print ti
Unfasten the print tip holding bolt. The print tip and print jet are assembled by sliding the print tip into the print jet and twisting it (as pictured). To remove the print jet you will need to twist it and pull down, eventually you will find the co
Removing the Jet Wipe. Run the bed to the bottom of the machine using manual move. Lift Jet wipe out of the machine. Removing the Case and floor panel.
Before beginning this process please ensure that all cartridges have been removed from the machine. Removing the Jet Wipe. Run the bed to the bottom of the machine using manual move. Lift Jet wipe out of the machine. Removing the Case and floor panel
and application of each motor, as well as its age, maintenance and repair history, operating condi- ...... as any performance tests required by the customer.
There was a problem previewing this document. Retrying... Download. Connect more apps... Try one of the apps below to open or edit this item. NOV2016 ...
man-21\1999-beetle-timing-belt-replacement-safe-search.pdf. man-21\1999-beetle-timing-belt-replacement-safe-search.pdf. Open. Extract. Open with. Sign In.
Cheap Replacement Accessory for Garmin VIRB X Com ... attery for Garmin VIRB XE X GPS Sport Camere.pdf. Cheap Replacement Accessory for Garmin VIRB ...
Watch Puppet Master X Axis Rising (2012) Full Movie Online.pdf. Watch Puppet Master X Axis Rising (2012) Full Movie Online.pdf. Open. Extract. Open with.
8 Mar 2006 - from the object B] Object-oriented programming is per formed by displaying objects connected by wirings that rep resent the ?ow of data, control or messages from one object to a second object. A coupling ofinput and output terminal so th
May 7, 2014 - o-y basis) in software & hardware sales, which although commanded a lower ... projects. There has not been much visibility on big order wins.
indicating their experience with similar engagements. In addition, any relevant. Continuing Education Programs should be listed. 9.1.5.1 Substitutions for the ...
ICB Sector: Software & Computer Services. Principal Business: Silverelake Axis provides customized software solutions for the banking industry. Source of all ...
There was a problem previewing this document. Retrying... Download. Connect more apps... Try one of the apps below to open or edit this item. Main menu.
OEM Seiko Robot Controller Motherboard numbers indicate how many connections to what there were 4 servo controller boards, 1 CPU board, and 1 I/O board.
