How to use Kisslicer with the CubeX. The Screen shots are using the Kisslicer Pro license and might be grayed out in the free version. (Try it and then buy it. It is cheap and so worth it) • • • • • • • • • • • • • • • •
Download the Kisslicer application. http://kisslicer.com/ Unzip the "Kisslicer_settings_CubeX_rev1.zip" file and place all files into the same directory or folder where you have your kisslicer.exe file. When you start kisslicer, it uses the four .ini files. If it does not find any .ini files, it will create default .ini files. Place also the "BedCubeX.stl" file into that same directory. Double click the Kisslicer exe file. The screen shots below point out settings you have to adjust depending if you print with PLA or ABS and with what printjet you want to print. There are pull down selections for PLA or ABS. Look thru the screen shots below and make necessary adjustments. Hover with the mouse button over the different settings, to get the pop up feature explanation. After you sliced the model, scroll thru the sliced file and see if you get the disired infill amount and support structure. Save the file. Then run the cubeIt.exe and open the kisslicer model file you just created. Then select the filament material. CubeIt creates a new file from your model file and a backup file. Copy the new file that CubeIt created (not the backup file) onto your memory stick and stick it in the cubeX. Select "Home", (always "Home" before checking / setting "z-gap". Select "Z-gap" to check the z-gap. (adjust if needed). Select print.
Note: The Kisslicer starts the first layer at a lower z-height than CubeX files. So you can add a "Z Offset" in the Kisslicer menu (In the Printer / Hardware tab of the Kisslicer software), or adjust your zgap accordingly. Test print a small part first. These settings are just base settings to get you started. See attached "Thin wall and solid cube calibration" document to fine tune / calibrate.
Kisslicer CubeX installation rev1.docx
Page 1 of 4
Select pulldown ABS or PLA or other pre settings.
Leave the speed setting selector in the middle
Select the desired infill amount.
Select the desired support amount. Check out the support after slicing and adjust if needed.
Select Material: PLA or ABS.
Kisslicer CubeX installation rev1.docx
Page 2 of 4
Here is where you load the CubeX printbed file. (It is included in the zipped files). Once loaded you don't need to load it again. Make sure to set the Bed Center X to -35.
If your first print layer is too squished down, you can add a z-offset here. Increase in 0.10 increments.
Here is where you select with what jet you want to print the part etc.
Make sure to select the Material file here. ABS or PLA or other custom.
In this example it would use the "ABS - CubeX" setting file and print everything with jet 3.
How to use Kisslicer with the CubeX. The Screen ... -
Unzip the "Kisslicer_settings_CubeX_rev1.zip" file and place all files into the ... created (not the backup file) onto your memory stick and stick it in the cubeX.
Download the Kisslicer application. http://kisslicer.com/ (attached in zip file is the ... to âKISSlicer64.exeâ (this was done because some email programs block.
Personality Types and the MBTI Method. Use the MBTI To Understand Personality Types. This tool is a personality diagnosis based on the work of Carl Jung. It is a way for. you to understand your âpreferredâ personality and the personalities of oth
Open Axure RP 8. The libraries and template files are created using version 8, they won't work in version 7 or earlier. We suggest you upgrade to the latest ...
There was a problem previewing this document. Retrying... Download. Connect more apps... Try one of the apps below to open or edit this item. Screen Free Week Books to Use 2017.pdf. Screen Free Week Books to Use 2017.pdf. Open. Extract. Open with. Si
support and dissolved, cannot be heated past. 200°c or ... Basic navigation - left click pans around window, mouse wheel zooms in and out and right click allows.
Try one of the apps below to open or edit this item. pdf-0943\the-small-screen-how-television-equips-us-to-live-in-the-information-age-by-brian-l-ott.pdf.
Sep 15, 2016 - For example, a male associate professor said, âI guess there's a perception among a lot of women that a career in engineering isn't desirable.
There was a problem previewing this document. Retrying... Download. Connect more apps... Try one of the apps below to open or edit this item. How to use the ...
Screencasts and tutorials are provided on pages to help you begin using the content presented. Pictures or pdf handouts provide visuals to reference while you are creating your own site or content. Forums allow you the opportunity to openly discuss w
smartphone, tablet and TV. The device we choose to use is often driven by our context: where we are, what we want to accomplish and the amount of. +me needed. There are two main modes of mul+-âscreening: SequenAal screening where we move between de
Many Ames we turn to the screen that's closest. While we all have screen preferences for certain ac+vi+es, we are also creatures of convenience of us use the ...
