IV B.Tech I Semester Supplementary Examinations, November 2005 POWER PLANT ENGINEERING (Mechanical Engineering) Time: 3 hours Max Marks: 80 Answer any FIVE Questions All Questions carry equal marks ????? 1. (a) Draw a chart showing operations and devices used in coal handling plant.[8+8] (b) Describe different types of coal conveyors.
2. (a) Explain the principle and operation of a spreader stroker with the help of a neat Sketch. [8+8]
or ld
(b) What is a stoker? Name the different types of stoker.
3. (a) Explain with the help of a block diagram the fuel storage and supply system of diesel power plant [8+8] (b) Explain with the help of a block diagram the water cooling system of diesel power plant 4. Explain cavitations, runway speed and the overall cost of a hydraulic turbine. [16] 5. (a) What are the advantages of a fuel cell?
[8+8]
uW
(b) Discuss the problems associated with the operation of a fuel cell.
6. (a) With a neat block diagram explain the governing system of a open cycle gas turbine power plant. [8+8] (b) Discuss the advantages of gas turbine power plant over diesel power plant. 7. (a) Explain the functions of cladding.
[4]
(b) Explain the characteristic features of Pressurized Water Reactor.
[8]
(c) Give a brief account of nuclear waste disposal.
[4]
nt
8. (a) Explain the significance of Load factor Diversity factor Plant capacity factor Plant use factor
Aj
i. ii. iii. iv.
[8]
(b) A residential consumer has 10 lamps of 40 watts each connected at his residence. His demand is [8] Midnight to 5 AM 40 watts 5 AM to 6 PM No load 6 PM to 7 PM 320 watts 7 PM to 9 PM 360 watts 9 PM to 12 Midnight - 160 watts 1 of 2
NR
Code No: NR410304 i. ii. iii. iv. v.
Plot the load curve Find average load max. Load Load factor Energy consumption during one day.
NR410304 IV B.Tech I Semester Supplementary ... Accounts
(b) Explain with the help of a block diagram the water cooling system of diesel · power plant · 4. Explain cavitations, runway speed and the overall cost of a ...
Write a C++ program that creates a data file containing list of Telephone numbers · and names. Use a class object to store set of data. 8. Write short notes on:.
The km value of an enzyme is known to be 0.01 mol/l. To measure the maximum rate of reaction rate catalyzed by the enzyme, the initial rate of reaction was ...
Discuss the Dynamic programming method to solve Unit commitment problem · in power systems. ... by 90°. Calculate the reactive power of the load. ^^^. OR.
NR. IV B.Tech I Semester Supplementary Examinations, November 2005 ... NR size is smaller than the fiber core, and the small gap between the source and.
RELIABILITY & SAFETY ENGINEERING · (Electronics & Control Engineering) ... (a) Explain the following terms in connection with reliability evaluation. [2+3].
NR. IV B.Tech I Semester Supplementary Examinations, November 2005 ... 3. Analyse the following frame using stiffness method. EI constant. (figure 3) [16].
What do you understand by Non-destructive testing techniques? List various tech- · nique of NDT and explain any three of them · [16]. 8. Write short notes on the ...
Using dynamic programming method, how do you find the most economical ... the additional reactive power requirement at the receiving end to meet a load of ...
(b) Explain the architecture of Honeywell 60/66 multiprocessor system. [8+8] · 6. (a) Define the term nonpreemptive scheduling. With an example illustrate the.
5. (a) Compare and contrast adaptive and fuzzy control techniques used in motion- ... Discuss various application of microprocessor control programmable logic ...
(b) Back to back DC link along with AC feeder. 2. Clearly explain the different converter configurations commonly employed for HVDC · converter and bring out ...
... No: NR410805. NR. IV B.Tech I Semester Supplementary Examinations, November 2005 ... ideal, Raoult's and Dalton's laws are applicable. [16] · *****. 2 of 2.
(c) Discuss the panel method for compressible subsonic and supersonic flows [6] · 6. (a) Derive a descretized form of generic integral form of continuity and ...
7. Distinguish between the power transmission by chains, ropes and wire ropes in · hoisting equipment. [16] · 8. Sketch and explain a hydraulic jack. [16] · *****.
(b) Clearly explain the use of category analysis in Trip generation models. [6] · 5. Explain the concept of Trip distribution. Disucss about the various growth factor.
DISTRIBUTED COMPUTER CONTROL SYSTEMS · (Electronics & Control ... (b) Explain the design techniques in real time systems. [8+8] · 5. Explain in detail ...
[8+8] · 2. Explain the mathematical interpretation of finite element method for ... (a) Show that the value of the shape function N1 of node i and node k of a simplex.
IV B.Tech I Semester Supplementary Examinations, November 2005. INTERNET & JAVA PROGRAMMING · (Electronics & Computer Engineering) · Time: 3 hours · Max Marks: 80 · Answer any FIVE Questions · All Questions carry equal marks · ***** · 1. (a) Defferet
Make a survey of petroleum reserves in the world and compare them with the · reserves available in India. Discuss the various exploration methods for finding.
(a) Explain the salient features of one, two and three wheeled hand trucks. (b) Distinguish between hand operated and power operated hand trucks. 5. What is meant by a hopper? Explain its uses in feeding equipments. 6. (a) Explain various types of fe
(a) What is Redundancy? Explain the different types of Redundancy operation with LCU. (b) explain the operation of: i. Operator interface. ii. Engineer interface.
