IV-B.Tech. I Semester Supplementary Examinations, May 2003 BUILDING PLANNING DESIGN & DRAWING (Civil Engineering) Time: 3 hours. Max. Marks: 80 Answer any Five questions All questions carry equal marks --1. Discuss the various factors or general principles which deserve due consideration by the architect in selection of site for a Building.
What do you understand by principles of planning a building? Prepare a typical aspect diagram for the area where direction of prevailing breeze is from Northwest.
3.a) b)
Write down general principles for natural ventilation. Explain in brief various systems of Mechanical ventilation.
4.
Explain with illustrative sketches the importance of unity, scale, balance and contrast in architectural compositions.
5.
With the help of the given data plan out a residential building. a) Dimensions of site 14m X 20m. b) Living room c) Bed room d) Kitchen and Store e) Dining room f) Front verandah g) Bath and W.C. 9m wide road is on the northern side of the plot. Plinth area is not to exceed 85 sqm. Draw a line diagram (not to scale) showing the dimensions of rooms. Also draw site plan denoting the open area.
6.
Discuss the salient features of the functional design of the following buildings. a) Office Buildings b) Industrial Buildings c) Educational Buildings
7.
Define sound insulators. What are the different methods of sound insulators?
nt
uW
or ld
2.
Write short notes on the following. a) Set back b) Building bye laws c) Absorbent materials d) Building line and control line.
Aj
8.
&&&&&
Set No.
2
Code No: 410104
.in
IV-B.Tech. I Semester Supplementary Examinations, May 2003 BUILDING PLANNING DESIGN & DRAWING (Civil Engineering) Time: 3 hours. Max. Marks: 80 Answer any Five questions All questions carry equal marks --1.
Mention the various Building aspects to be considered under Regulations and Bye laws, by the architect while planning and designing the lay out of the building.
2.
Write explanatory notes on a) Control line b) 63½ degree rule
d) Circulation.
or ld
c) Grouping in plan
How is artificial or mechanical ventilation achieved? What do you understand by orientation? What are the criteria that are used in deciding orientation?
4.
Discuss the importance of form, function, scale and proportion in architectural composition with illustrative sketches.
5.
A residential building is to be planned in a plot of 24m X 18m with a road frontage of 18m on west. Draw a line diagram (not to scale) showing the dimensions of room. The following accommodation is to be provided. Assume any data required. a) Drawing room 2) Bed room 3) Kitchen cum Dining 4) Bath and W/C 5) Stair case. Also draw site plan denoting the open areas.
6.
Discuss the salient features of the functional designs of the following buildings a) Auditorium b) Office Buildings e) Hospitals.
7.a)
What do you understand by absorption of sound? How does this take place? Enumerate various absorption surfaces. Explain various methods of sound insulation through the wall of a hall.
nt
uW
3.a) b)
b)
Write short notes on the following; a) set-back b) Sanitary convenience c) Privacy in Building d) Floor Space Index.
Aj
8.a)
&&&&&
Set No.
3
Code No: 410104
.in
IV-B.Tech. I Semester Supplementary Examinations, May 2003 BUILDING PLANNING DESIGN & DRAWING (Civil Engineering) Time: 3 hours. Max. Marks: 80 Answer any Five questions All questions carry equal marks --1. What is the significance of open space around a building? Give the criteria in this regard and specify the space requirements for a residential type of building. Write explanatory notes on: a) Building line b) Set-back c) Sanitary conveniences d) privacy in a building
3.a) b)
Discuss in brief the functional requirements of ventilation system. Define sun path diagram. How are solar charts useful in the design of a building?
4.
Explain the significance of the following terms as used in architectural design: unity, scale and balance.
5.
A residential building is to be planned in a plot of land 15m X 20m. The 15m side is on north side adjoining a 18m wide road. The maximum permissible plinth area is 100m2. The following accommodation is to be provided: a) Drawing room b) Bed room with attached bath room c) Bed room d) Kitchen cum dining e) Bath and W.C. f) Out side stair case for access to terrace.
uW
or ld
2.
Draw a line diagram (not to scale) showing the dimensions. Assume any data necessary. Also draw a site plan denoting the open area. Discuss the salient features of the functional designs of the following buildings a) Educational buildings b) Hotels c) Buildings for recreation.
7.
Explain a) Reverberation time b) Optimum reverberation time. Indicate how the acoustics of a building can be predicted during the planning stage of the building. Explain also how the acoustics of an existing building can be improved.
nt
6.
Write short notes on the following: a) Building Bye laws b) Grouping in plan c) Circulation d) Guide lines for selection of a site.
Aj
8.
&&&&&
Set No.
4
Code No: 410104 IV-B.Tech. I Semester Supplementary Examinations, May 2003 BUILDING PLANNING DESIGN & DRAWING (Civil Engineering) Time: 3 hours.
Answer any Five questions All questions carry equal marks --Discuss briefly the various principles of planning buildings. significance of aspect and prospect of residential buildings.
.in
1.
Max. Marks: 80
Explain the
Discuss the criteria of determining the maximum permissible height of a building. Define the height of a room and specify the absolute minimums for various rooms and apartments in this regard.
3.a) b)
What are the points to be observed incase of natural ventilation? Briefly explain about the wall thickness.
4.
State the principles of architectural composition and explain the following as used in architectural design: proportion, rhythm and massing.
5.
A residential building is to be planned in a plot of land 15m X 20m. The 15m side is on east side adjoining a 12m wide road. The maximum permissible plinth area is 105m2. The following accommodation is to be provided: a) Drawing room b) Bed room – 2m (one attached bath) c) Kitchen cum dining d) Bath and W.C e) Out side staircase for access to terrace. Draw a line diagram (not to scale) showing the dimensions. Assume any data necessary. Also draw a side plan denoting the open area.
6.
Discuss the salient features of the functional designs of the following buildings: a) Hospitals b) Banks c) Industrial Buildings
nt
uW
or ld
2.a) b)
Explain the various acoustical defects in an auditorium and suggest the remedies for them. Draw figures to illustrate your answer.
8.
Write short notes on the following a) Reverberation time b) Guide lines for selection of a site e) Building line and control line d) 63½ degree rule for fixing the height of a building
What do you understand by principles of planning a building? Prepare a typical · aspect diagram for the area where direction of prevailing breeze is from North-.
List out the practical considerations to be checked for continuous gas ... Explain how silica analysis is done in boiler water of power plant. 3. a) What is meant by ...
b) Draw the circuit diagram of 4-bit Johnson counter using D-flip flop and explain .... 6. a) Compare merits and demerits of ripple and synchronous counters.
Given: turbine diameter = 120m and turbine operating speed = 40 rpm at · maximum efficiency. Propeller type wind turbine is considered. 4. a) What is the basic ...
Obtain an expression for unit speed, unit discharge and unit power for a turbine. 2. a) What do you understand by air vessels? Explain with a neat sketch.
1.a) Obtain the expression for the resistance and capacitance for gas system. ... List various variables to be measured and controlled in nuclear power plant.
instructions at the beginning and end of this set of code in order to switch .... 5.a) Write an assembly language program that will examine an ASCII string of 100.
If the analog i/p voltage is +6.85 v, what will be the R-2R ladder · o/p voltage when ... b) Design a ramp generator using 555 timer having an output frequency of.
efficiency of the cycle and mean effective pressure for the cycle. ... b) Calculate the heat flux emitted due to thermal radiation from a black surface at · 6000.
8.a) Write a note on creep resistant materials. b) Explain all the ... b) Sketch the creep diagram, and explain the various stages of creep. @@@@@. Set No. 2.
What is the difference between radio compass and ADF? Explain the principle · and operation of Automatic direction finder. 6. Define analog and digital ...
endurance limit of a metal. b) What are the factors which affect the fatigue strength of materials? 7. a) What is creep? Draw an ideal creep curve and explain the ...
(i) Band Rate · (ii) Request Filter ... 3. a) Write the comparison between teleprinters and CRT terminals. b) What are the ... What savings does it offer? b) What is a ...
b) How does butadiene differ from isoprene? 4.a) Describe about the synthetic fiber industry in India. b) Write, with an example on each of the following.
graph. b) Draw the state space tree for m-closing graph using a suitable graph. 8. Present a program schema for a FIFO Branch & Bound search for a Least-Cost.
b) Explain the effect of Metallurgical variables on fatigue properties · 7.a) Explain Ductile to Brittle transition phenomenon. b) Compare charpy with Izod impact testing. 8.a) What is stress relaxation. Draw stress-strain curves for ductile and brit
Information Technology, Electronics and Control Engineering, Electronics and ... Computer Engineering, Computer Science and System Engineering) ..... Draw and explain the logic diagram of a master slave D flip-flop using Nand gates. ###.
Chemical Engineering, Mechatronics, Metallurgy & Material Technology, · Aeronautical ... b) What is cache memory? Where is it placed? What is its .... 7.a) Explain the steps involved in computing the coefficients of the regression · polynomial.
b) Classify the blast furnace stoves. What are the different values in the stove and · their functions? 3.a) What factors affect reducibility of iron ores? Discuss them.
1.a) Write the name of places for occurance of iron ores in India. b) Explain the process of either Sintering or Pelletizing. 2.a) Explain hearth, tuyeres, stack with ...
What are lubricants and flow promoters? What are internal and external · lubricants? What is the effect of lubricants on the properties of polymers? 8. Write short ...
