II B.Tech II Semester Supplementary Examinations, November/December 2005 BUILDING PLANNING (DESIGN AND DRAWING) (Civil Engineering) Time: 3 hours Max Marks: 80 Answer any FIVE Questions All Questions carry equal marks ????? 1. Write short notes on the following: (a) Building bye-laws. (b) Classification of buildings.
[6+5+5]
or ld
(c) Open spaces in buildings.
2. (a) Suggest the minimum area requirement for the following areas in residences: i. ii. iii. iv.
Habitable room Kitchen Bath Room Stair Case
[2+2+2+2]
(b) What minimum height do you recommend for Plinth Habitable rooms Head room for stair case Depth of foundation
uW
i. ii. iii. iv.
[2+2+2+2]
3. Discuss in detail the important factors that should be kept in mind while planning a building. [16] 4. Discuss the practical design considerations to be followed in buildings in:
nt
(a) Hot dry zones.
(b) Hot humid zones. (c) Cool zones.
[6+5+5]
Aj
5. Briefly explain the principles of composition of buildings, emphasizing scale and proportion. [16] 6. Write short notes on the characteristics of the following house types: (a) Apartments .
(b) Row houses . (c) Independent and semi-detached houses.
1 of 3
[5+5+6]
NR
Code No: NR220107
7. Design an village panchayat office for the following requirements and draw a line diagram . (a) Entrance and waiting room . (b) Meeting hall to accommodate 40 people. (c) V.P. President Chambers with attached toilet. (e) Office for 10 staff . (f) Toilet blocks - 2 Nos. (g) Necessary provision to be made for corridors.
.in
(d) V.P. Secretary Chambers with attached toilet .
[16]
8. Note: The following specifications may be taken unless otherwise specified in the
or ld
individual line plans.
The line plan in the figure below shows the internal dimensions in mm. Draw to a suitable scale the following views: (a) Plan
(b) Sectional Elevation Select suitable positions and sizes of doors and windows According your choice, if it not given in the line plans. The specifications for the buildings are as follows:
Aj
nt
uW
i. Foundation depth below ground level. . . . . . . . . . . . . . . . . . . . . . . . ..1.1.m ii. Plinth height above ground level . . . . . . . . . . . . . . . . . . . . . . . . . . . ...1.0 m iii. Mansonry in foundation and up to plinth – Uncoused rubble masonry in lime mortar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1:2. iv. Mansonry in superstructure -11/2 brick in cement mortar 1:6 v. Flooring – 25 mm thick mosaic tiles on 100mm thick 1:4:8 concrete bed. vi. Doors – Timber doors fully paneled at suitable places and of suitable sizes. vii. Windows – Timber fully glazed at suitable places and of suitable sizes. viii. Roof: A. for sloped roof – A.C.sheets over timber purlins or mangalore tiled roof. B. for flat R.C.C.roof – 120mm thick R.C.C.slab of 1:2:4 with 80mm thick wearing course.
Assume any other suitable data wherever required and mention the same in the drawing.(figure1)
(c) Open spaces in buildings. [6+5+5] ... (c) Independent and semi-detached houses. [5+5+6]. 1 of 3 ... (c) V.P. President Chambers with attached toilet. (d) V.P. ...
(a) Job order production and batch production system. (b) Mass production and flow production. [4+4+4+4] · 7. DefineâCritical pathâ, âslack timeâand âDummy ...
(b) One bag contains 4 White balls and 3 black balls and a second bag contains 3 ... [8+8] · 3. (a) The amount of bread ( in hundreds of pounds) X that a certain ...
(c) Explain sign conventions of heat and work in thermodynamics. [5+5+6] · 3. (a) State and explain second law of thermodynamics. (b) Define and explain ...
b=4.318 cm is fed by a 4 GHz carrier from a coaxial cable. Determine if a · TE10 mode will be propagated. If so calculate the phase velocity and group · velocity.
(c) An amplifier with voltage gain of 60 decibels uses 0.05 of its output voltage in · negative feedback. Calculate the gain of the feedback amplifier. [6+6+4].
Determine the length of the wire needed if the diameter · of the wire is 0.25 mm. Assuming that the temperature coefficient of resis- · tance of the wire is constant, ...
(b) Draw the block schematic of 4x1 MUX and give its truth table. [6] · 6. (a) Design a full adder with minimum number of NAND gates. [8] · (b) Draw the logic ...
8. (a) Enumerate various mechanical and diffusion properties of cartilage with ex- · amples? [8] · (b) Write briefly about âlubricationâ of joints? [8] · *****. 1 of 1.
starter, (iii) Auto transformer starter limiting the supply line starting current to · twice the full-load value. Find the auto-transformer tapping in this case. - - -.
(a) Apply the Bresenham's algorithm to turn up pixels along the line segment determined by points (5,7) and (12,11). (b) Give parametric equation of a line ...
a) Follower moves outwards through 40mm during 60° of cam rotation. ... Draw the profile of the cam when the axis of the follower is offset 20mm towards.
a(m,n) = a(m-1,a(m,n-1)) if m!=0,n!=0 · (b) Determine what does ... [8+8] · 4. If an array holding a queue is not considered circular, the general method suggests.
error in the reading due to loading effect. 2. (a) Explain in detail the measurement of power using electrodynamometer. (b) Write short notes on watt-hour meter.
SIMULA. b) What is concurrency ? Briefly explain the concurrency features in ADA. 8. Briefly explain the following : · (a) · Basics of LISP · (b) · Type equivalence.
Code No. 220555. II B.Tech. II-Semester Supplementary Examinations November-2003 · PROGRAMMING LANGUAGES · (Common to Computer Science and Engineering and Computer Science and · Information Technology) · Time: 3 hours · Max. Marks:70 · Answer any Fiv
articular cartilage surfaces. 7.a) With the help of a P-V curve of a lung, explain the normal breathing mechanism. b) What are the lung mechanical parameters.
8.a) What are the constraints on ROC for various classes of signals in z transform? b) Find the z transform of the sinusoidal signal XT (n)=sin (bn)*uT (n).
