Set No:

1

1.a) b)

.in

Code No: NR- 410309 IV-B.Tech. I-Semester supplementary Examinations, May-2004 UNCONVENTIONAL MACHINING PROCESS (Common to Mechanical Engineering and Production Engineering) Time: 3 Hours Max. Marks: 80 Answer any FIVE questions All questions carry equal marks ----

With the help of a neat sketch, explain how material is removed from a work piece in ultrasonic machining process. Explain the various factors affecting the material removal rate in ultrasonic machining process. Describe the role of nozzle in water jet machining. Explain how the distance between nozzle and work piece influence the material removal rate.

3.a)

Distinguish between etch rate and etch factor. Why are they important in Chemical Machining? How do you estimate them? What is the care required in demasking? How is it achieved?

4.a)

b) c)

What are the different modes of dielectric flushing used in E.D.M. Which method of flushing the inter electrode gap yields improved M.R.R. and why?

nt

5.

A Nimonic 75 alloy has the following composition. Ni -72.5%, Cr -19.5%, Fe5.0%, Ti -0.4% and the rest of elements can be ignored. The atomic weights of Ni, Cr, Fe, and Ti are 58.71, 51.99, 55.85 and 47.9 respectively and their valencies are 2, 3, 2, and 2 respectively. This is machined using Electro Chemical Machining at a current of 560 Amp. Determine the theoretical machining rate using the percentage weight method. Time of machining 10 minutes. State the assumptions made, if any. Calculate the anodic efficiency in the above case if the actual metal removal rate is found as 174 gms and comment on the result. Can the efficiency value in the above case be improved? If so, suggest a method?

uW

b)

or ld

2.a) b)

Describe the advantages and limitations of power supply with rotary impulse generator circuit used in EDM.

7. a)

What do you mean by power density in case of LBM? Write the formula to calculate the power density and explain each term. Explain the process characteristics of LBM

Aj

6.

b)

8.

Derive an expression for the pressure to be applied by the hydraulic system in hydrostatic extrusion. @&@&@

Set No: Code No: NR- 410309 IV-B.Tech. I-Semester supplementary Examinations, May-2004 UNCONVENTIONAL MACHINING PROCESS (Common to Mechanical Engineering and Production Engineering)

2

2.a) b)

3.a) b) c) 4.a)

Explain the use of Electro Chemical Machining in air craft industries. With a suitable sketch explain the tooling arrangement to produce one of the products for aircraft industry. Perform economic analysis on the above product with data assumed. Suitably. In a certain Electro Chemical Machining of a metallic die, a metal removal rate of 2 cm3/min is desired. Determine the current required for machining given that: Atomic weight: 56 gms Valency of dissolution: 2 Density of material: 7.8 gms / cm3 Voltage: 45 volts Electrolyte velocity: 20 m /sec. Inter Electrode gap: 0.05 mm Electrolyte type & concentration: 20% sodium chloride. State the assumptions made in the above case.

nt

b)

Write a note on the accuracy and surface finish levels achieved in abrasive jet machining. Write a note on the accuracy and surface finish levels achieved in water jet machining.

or ld

b)

uW

1.a)

Max. Marks: 80 Answer any FIVE questions All questions carry equal marks ---Explain the influence of grain size of abrasives in ultrasonic matching on the surface finish characteristics of the machined surface. Explain how various process parameters influence the material removal rate in ultrasonic machining process.

.in

Time: 3 Hours

Explain how to sink a square blind hole in tungsten work electrode using copper as tool electrode using E.D.M.

6.a) b)

What are the advantages and disadvantages of E.D.M. process -explain in detail. With neat sketch, explain the closed loop hydraulic circuit used in E.D.M process.

Aj

5.

7.a)

b)

8.

What is laser? State some important properties of laser that makes it suitable for machining or welding. Explain the working of a typical laser system for machining process..

What types of defects are observed in unconfined explosive forming? What are the reasons for them? What remedies are suggested by you to avoid these defects? @&@&@

Set No:

3

Code No: NR- 410309 IV-B.Tech. I-Semester supplementary Examinations, May-2004 UNCONVENTIONAL MACHINING PROCESS (Common to Mechanical Engineering and Production Engineering)

1.a) b)

Max. Marks: 80 Answer any FIVE questions All questions carry equal marks ---Explain the applications, advantages and limitations of ultrasonic machining process. Briefly explain the characteristics of ultrasonic machining process.

.in

Time: 3 Hours

Explain the process of Water Jet Machining with a neat sketch. Compare the specific energy consumption by PAM and WJM.

3.a) b)

Explain the process of ECG with a neat sketch. In an ECM operation with the flat surfaces, a 10 V DC supply is used. The conductivity of the electrolyte is 0.2 ohm-1 cm-1, and a feed rate of 1 mm/min. is used. The workpiece is of pure iron. Calculate the equilibrium gap. Consider the total over voltage to be 1.5 V.

4.a)

Determine the metal removal rate in Electro Chemical Machining given the Following. Voltage across the tool and workpiece: 42 volts. Over voltages: 2.2 volts Interelectrode gap: 0.1 mm Electrolyte flow velocity: 15 m / sec. Electrolyte type and Concentration: 18% Sodium Chloride Density of material: 8 gms / cm3 Atomic weight: 55.9 gms Valency of dissolution: 2 State the assumptions made in the above case.

uW

b)

or ld

2.a) b)

Metal removal rate is a function of pulse voltage, pulse current and pulse duration -Explain the effect of increase of each parameter keeping the other two constant on M.R.R.

6.a) b)

What are the various process parameters which influence the MRR? What materials are used for Electrodes? Mention the relative advantages.

Aj

nt

5.

7.a) b)

Discuss about various types of plasma torches. Discuss about work environments and safety precautions in plasma arc machining.

8.

What types of defects are observed in expanding type electro-magnetic hydraulic forming? What are the reasons for them? What remedies are suggested by you to avoid these defects? @&@&@

Set No:

4

Code No: NR- 410309 IV-B.Tech. I-Semester supplementary Examinations, May-2004 UNCONVENTIONAL MACHINING PROCESS (Common to Mechanical Engineering and Production Engineering)

1.a) b)

Max. Marks: 80 Answer any FIVE questions All questions carry equal marks ---Explain the influence of work piece hardness and tool hardness on metal removal rate in ultrasonic machining process. Describe how abrasive grit size influences the surface roughness of the machined surfaces in USM.

.in

Time: 3 Hours

What are the materials machined with Water Jet Machining? State the advantages of Water Jet Machining.

3.a) b) c)

How does the electrolyte temperature vary the machining rate in ECM Why the gap between the electrode and the work piece is important in ECM Compare the specific energy consumptions for removing unit volume of metal by ECM and EDM processes.

4.a) b)

Draw out the differences in the processes of ECM & EDM Calculate the Metal Removal Rate and electrode feed rate when iron is machined by ECM. Electrode used is Copper. Electrolyte is Sodium Chloride solution, with specific resistance 5 ohm-cm. Supply voltage 20 V DC. Current 5000 Amp. Tool work gap of 0.5 mm. Atomic weight of iron is 56. Density of iron 7.87x 106 gm/m3.

5.

Explain the various industrial applications of Electric Discharge Machining (E.D.M.) with examples.

nt

uW

or ld

2.a) b)

6.a)

Aj

b)

What are the various flushing methods be employed in EDM to increase the efficiency of machining. Mention their relative advantages. How the wear ratio and mental removal rate are influenced by the selection of tool material in EDM.

7.a)

b)

8.

Discuss with neat sketches about the five basic units of Electron beam drilling equipments. Name the materials that can be machined by the laser and name few material that cannot be machined by laser. What types of defects are observed in liquid forging? What are the reasons for them? What remedies are suggested by you to avoid these defects? @&@&@

Set No:

... supplementary Examinations, May-2004 · UNCONVENTIONAL MACHINING PROCESS · (Common to Mechanical Engineering and Production Engineering).
Download PDF
117KB Sizes 1 Downloads 122 Views
Report

Recommend Documents

Set No:
List out the practical considerations to be checked for continuous gas ... Explain how silica analysis is done in boiler water of power plant. 3. a) What is meant by ...
Set No.
What do you understand by principles of planning a building? Prepare a typical · aspect diagram for the area where direction of prevailing breeze is from North-.
Set No.
b) Draw the circuit diagram of 4-bit Johnson counter using D-flip flop and explain .... 6. a) Compare merits and demerits of ripple and synchronous counters.
Set No.
Given: turbine diameter = 120m and turbine operating speed = 40 rpm at · maximum efficiency. Propeller type wind turbine is considered. 4. a) What is the basic ...
Set No.
Obtain an expression for unit speed, unit discharge and unit power for a turbine. 2. a) What do you understand by air vessels? Explain with a neat sketch.
Set No
+ 2x1x2 – 4x2x3 – 2x3x1. b) · Define the following terms: (i) objective function surfaces (ii) constraint surface · (iii) bound points. 3.a) Maximize f= 8x1 + 4x2 + ...
Set No.
1.a) Obtain the expression for the resistance and capacitance for gas system. ... List various variables to be measured and controlled in nuclear power plant.
Set No.
instructions at the beginning and end of this set of code in order to switch .... 5.a) Write an assembly language program that will examine an ASCII string of 100.
Set No.
If the analog i/p voltage is +6.85 v, what will be the R-2R ladder · o/p voltage when ... b) Design a ramp generator using 555 timer having an output frequency of.
Set No.
efficiency of the cycle and mean effective pressure for the cycle. ... b) Calculate the heat flux emitted due to thermal radiation from a black surface at · 6000.
Set No.
8.a) Write a note on creep resistant materials. b) Explain all the ... b) Sketch the creep diagram, and explain the various stages of creep. @@@@@. Set No. 2.
Set No:
What is the difference between radio compass and ADF? Explain the principle · and operation of Automatic direction finder. 6. Define analog and digital ...
Set No.
endurance limit of a metal. b) What are the factors which affect the fatigue strength of materials? 7. a) What is creep? Draw an ideal creep curve and explain the ...
Set No.
(i) Band Rate · (ii) Request Filter ... 3. a) Write the comparison between teleprinters and CRT terminals. b) What are the ... What savings does it offer? b) What is a ...
Set No.
Code No.: 220107 · II B.Tech. Regular Semester Examinations April, 2003 · BUILDING PLANNING (DESIGN & DRAWING) · (Civil Engineering) · Time: 3 hours.
Set No:
b) How does butadiene differ from isoprene? 4.a) Describe about the synthetic fiber industry in India. b) Write, with an example on each of the following.
Set No:
graph. b) Draw the state space tree for m-closing graph using a suitable graph. 8. Present a program schema for a FIFO Branch & Bound search for a Least-Cost.
Set No:
Code No: 410105. IV B. Tech I-Semester Regular Examinations, November-2004. ADVANCED STRUCTURAL ANALYSIS · (Civil Engineering) · Time: 3 hours.
Set No
b) Explain the effect of Metallurgical variables on fatigue properties · 7.a) Explain Ductile to Brittle transition phenomenon. b) Compare charpy with Izod impact testing. 8.a) What is stress relaxation. Draw stress-strain curves for ductile and brit
Set. No.
Information Technology, Electronics and Control Engineering, Electronics and ... Computer Engineering, Computer Science and System Engineering) ..... Draw and explain the logic diagram of a master slave D flip-flop using Nand gates. ###.
Set No.
Chemical Engineering, Mechatronics, Metallurgy & Material Technology, · Aeronautical ... b) What is cache memory? Where is it placed? What is its .... 7.a) Explain the steps involved in computing the coefficients of the regression · polynomial.
Set No.
b) Classify the blast furnace stoves. What are the different values in the stove and · their functions? 3.a) What factors affect reducibility of iron ores? Discuss them.
Set No.
1.a) Write the name of places for occurance of iron ores in India. b) Explain the process of either Sintering or Pelletizing. 2.a) Explain hearth, tuyeres, stack with ...
Set No
Code No.: 320101. III-B.Tech. II-Semester Examinations April 2003 · STRUCTURAL ANALYSIS –II · (Civil Engineering) · Time: 3 Hours · Max. Marks: 80.